ISO 813-2:2024

Rubber, vulcanized or thermoplastic — Determination of adhesion to a rigid substrate — Part 2: Adhesion of a soft thermoplastic elastomer layer

This document specifies a test method for assessing the peel strength of a thermoplastic elastomer (TPE) to a rigid substrate. It is mainly applicable to soft components in the Shore A hardness range. This document specifies a test piece but not the injection moulding tool for its manufacture. Hence, it is possible that different results are obtained for test pieces produced using different injection moulding tools.

Caoutchouc vulcanisé ou thermoplastique — Détermination de l'adhérence à un substrat rigide — Partie 2: Adhérence d'une couche d'élastomère thermoplastique souple

General Information

• Status: Published
• Publication Date: 22-Feb-2024
• ICS: 83.060 - Rubber
• Technical Committee: ISO/TC 45/SC 2 - Testing and analysis
• Drafting Committee: ISO/TC 45/SC 2 - Testing and analysis
• Current Stage: 6060 - International Standard published
• Start Date: 23-Feb-2024
• Due Date: 24-Mar-2025
• Completion Date: 23-Feb-2024

Standards Content (Sample)

International
Standard
ISO 813-2
First edition
Rubber, vulcanized or
2024-02
thermoplastic — Determination of
adhesion to a rigid substrate —
Part 2:
Adhesion of a soft thermoplastic
elastomer layer
Caoutchouc vulcanisé ou thermoplastique — Détermination de
l'adhérence à un substrat rigide —
Partie 2: Adhérence d'une couche d'élastomère thermoplastique
souple
Reference number
ISO 813-2:2024(en) © ISO 2024

---------------------- Page: 1 ----------------------
ISO 813-2:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland

© ISO 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO 813-2:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
5.1 Tensile testing machine .2
5.2 Test trolley .2
6 Calibration . 3
7 Test pieces . 3
7.1 Form and dimensions .3
7.2 Test piece fabrication using the injection moulding method .4
7.3 Test piece with inserted rigid substrate.5
7.4 Number of test pieces .5
8 Conditioning . 5
9 Test conditions .
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 813-2
ISO/TC 45/SC 2
Rubber, vulcanized or
Secretariat: JISC
thermoplastic — Determination of
Voting begins on:
2023-11-20 adhesion to a rigid substrate —
Voting terminates on:
Part 2:
2024-01-15
Adhesion of a soft thermoplastic
elastomer layer
Caoutchouc vulcanisé ou thermoplastique — Détermination de
l'adhérence à un substrat rigide —
Partie 2: Adhérence d'une couche d'élastomère thermoplastique
souple
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 813-2:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 1 ----------------------
ISO/FDIS 813-2:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 813-2
ISO/TC 45/SC 2
Rubber, vulcanized or
Secretariat: JISC
thermoplastic — Determination of
Voting begins on:
adhesion to a rigid substrate —
Voting terminates on:
Part 2:
Adhesion of a soft thermoplastic
elastomer layer
Caoutchouc vulcanisé ou thermoplastique — Détermination de
l'adhérence à un substrat rigide —
Partie 2: Adhérence d'une couche d'élastomère thermoplastique
souple
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: [phone]
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: [e-mail]
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 813-2:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
  © ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 2 ----------------------
ISO/FDIS 813-2:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
5.1 Tensile testing machine . 2
5.2 Test trolley . 2
6 Calibration .
...

ISO/DISFDIS 813-2:2023(E)
ISO/TC 45/SC 2/WG 1
Date: 2023-07
Secretariat: JISC
Date: 2023-11-06
Rubber, vulcanized or thermoplastic — Determination of
adhesion to a rigid substrate — —
Part 2:
Adhesion of a soft thermoplastic elastomer layer
Caoutchouc vulcanisé ou thermoplastique — Détermination de l'adhérence à un substrat rigide —
Partie 2: Adhérence d'une couche d'élastomère thermoplastique souple
FDIS stage

---------------------- Page: 1 ----------------------
ISO/DISFDIS 813-2:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this
publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,
including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can
be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
EmailE-mail: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
ii © ISO 2023 – All rights reserved
 © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DISFDIS 813-2:2023(E)
Contents
Foreword . iv
Introduction . v
Part 2: Adhesion of a soft thermoplastic elastomer layer . 1
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
5.1 Tensile testing machine . 2
5.2 Test trolley . 2
6 Calibration . 4
7 Test pieces . 4
7.1 Form and dimensions . 4
7.2 Test piece fabrication using the injection moulding method . 6
7.3 Test piece with inserted rigid substrate . 7
7.4 Number of test pieces . 7
8 Conditioning . 7
9 Test conditions . 9
10 Procedure . 9
11 Expression of results . 9
11.1 Peel strength
...