ISO/IEC 19762-5:2008

Information technology — Automatic identification and data capture (AIDC) techniques — Harmonized vocabulary — Part 5: Locating systems

ISO/IEC 19762-5:2008 provides terms and definitions unique to locating systems in the area of automatic identification and data capture techniques. This glossary of terms enables the communication between non-specialist users and specialists in locating systems through a common understanding of basic and advanced concepts.

Technologies de l'information — Techniques automatiques d'identification et de saisie de données (AIDC) — Vocabulaire harmonisé — Partie 5: Systèmes de localisation

General Information

• Status: Withdrawn
• Publication Date: 10-Jun-2008
• Withdrawal Date: 10-Jun-2008
• ICS: 01.040.35 - Information technology (Vocabularies)
• ICS: 35.040 - Information coding
• ICS: 35.040.50 - Automatic identification and data capture techniques
• Technical Committee: ISO/IEC JTC 1/SC 31 - Automatic identification and data capture techniques
• Drafting Committee: ISO/IEC JTC 1/SC 31 - Automatic identification and data capture techniques
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 03-Feb-2016

Relations

• Revised: ISO/IEC 19762:2016 - Information technology — Automatic identification and data capture (AIDC) techniques — Harmonized vocabulary
• Effective Date: 10-Jan-2012

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 19762-5
First edition
2008-06-15


Information technology — Automatic
identification and data capture (AIDC)
techniques — Harmonized vocabulary —
Part 5:
Locating systems
Technologies de l'information — Techniques automatiques
d'identification et de saisie de données (AIDC) — Vocabulaire
harmonisé —
Partie 5: Systèmes de localisation




Reference number
ISO/IEC 19762-5:2008(E)
©
ISO/IEC 2008

---------------------- Page: 1 ----------------------
ISO/IEC 19762-5:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO/IEC 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO/IEC 2008 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 19762-5:2008(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Classification of entries . 1
3 Terms and definitions. 1
4 Abbreviations . 2
Bibliography . 3
Index. 4

© ISO/IEC 2008 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/IEC 19762-5:2008(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 19762-5 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 31, Automatic identification and data capture techniques.
ISO/IEC 19762 consists of the following parts, under the general title Information technology — Automatic
identification and data capture (AIDC) techniques — Harmonized vocabulary:
⎯ Part 1: General terms relating to AIDC
⎯ Part 2: Optically readable media (ORM)
⎯ Part 3: Radio frequency identification (RFID)
⎯ Part 4: General terms relating to radio communications
⎯ Part 5: Locating systems
iv © ISO/IEC 2008 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/IEC 19762-5:
...