Ships and marine technology — Pipework and machinery — Information transfer

ISO 8277:2013 specifies the minimum data needed for the prefabrication and assembly of pipework and for its transfer from engineering departments to workshops in the shipbuilding industry. ISO 8277:2013 is applicable to written information needed for construction of piping installations that marine piping equipment manufacturers submit through specifications and instructions to shipyards on shipbuilding. ISO 8277:2013 is not applicable to the generation, type presentation and filing organization of this data.

Navires et technologie maritime — Tuyauteries et machines — Transmission d'informations

General Information

Status
Published
Publication Date
23-May-2013
Current Stage
9060 - Close of review
Start Date
04-Jun-2029
Ref Project

Relations

Buy Standard

Standard
ISO 8277:2013 - Ships and marine technology -- Pipework and machinery -- Information transfer
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 8277
Second edition
2013-06-01
Ships and marine technology —
Pipework and machinery —
Information transfer
Navires et technologie maritime — Tuyauteries et machines —
Transmission d’informations
Reference number
ISO 8277:2013(E)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO 8277:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 8277:2013(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Pipework information . 1
3.1 Information on standard parts . 1
3.2 Information on non-standard parts . 2
3.3 Administrative information . 4
4 Flow chart . 6
Bibliography . 8
© ISO 2013 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 8277:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 8, Ships and marine technology, Subcommittee
SC 3, Piping and
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.