ISO/IEC/IEEE 24748-8:2019

Systems and software engineering — Life cycle management — Part 8: Technical reviews and audits on defense programs

This document establishes the requirements for technical reviews and audits to be performed throughout the acquisition life cycle for the US Department of Defense (DoD) and other defense agencies. This document provides the definition, description, and intent, as well as the entry, exit and success criteria, for each technical review and audit. It is to be used to establish agreement between acquirers and suppliers on the technical reviews and audits that are needed for the project, as well as the focus and expectations of each technical review and audit.

Ingénierie des systèmes et du logiciel — Gestion du cycle de vie — Partie 8: Revues techniques et audits des programmes de défense

General Information

• Status: Published
• Publication Date: 05-Feb-2019
• ICS: 35.080 - Software
• Technical Committee: ISO/IEC JTC 1/SC 7 - Software and systems engineering
• Drafting Committee: ISO/IEC JTC 1/SC 7 - Software and systems engineering
• Current Stage: 9020 - International Standard under periodical review
• Start Date: 15-Jan-2024
• Completion Date: 15-Jan-2024

Standards Content (Sample)

INTERNATIONAL ISO/IEC/
STANDARD IEEE
24748-8
First edition
2019-02
Systems and software engineering —
Life cycle management —
Part 8:
Technical reviews and audits on
defense programs
Ingénierie des systèmes et du logiciel — Gestion du cycle de vie —
Partie 8: Revues techniques et audits des programmes de défense
Reference number
ISO/IEC/IEEE 24748-8:2019(E)
©
 IEEE 2015

---------------------- Page: 1 ----------------------
ISO/IEC/IEEE 24748-8:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© IEEE 2015
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO or IEEE at
the respective address below or ISO’s member body in the country of the requester.
ISO copyright office Institute of Electrical and Electronics Engineers, Inc
CP 401 • Ch. de Blandonnet 8 3 Park Avenue, New York
CH-1214 Vernier, Geneva NY 10016-5997, USA
Phone: [phone]
Fax: [phone]
Email: [e-mail] Email: [e-mail]
Website: www.iso.org Website: www.ieee.org
Published in Switzerland
© IEEE 2015 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO/IEC/IEEE 24748-8:2019(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are
members of ISO or IEC participate in the development of International Standards through technical
committees established by the respective organization to deal with particular fields of technical
activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other
international organizations, governmental and non‐governmental, in liaison with ISO and IEC, also
take part in the work. In the field of information technology, ISO and IEC have established a joint
technical committee, ISO/IEC JTC 1.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for
the different types of ISO documents should be noted (see www.iso.org/directives).
IEEE Standards documents are developed within the IEEE Societies and the Standards Coordinating
Committees of the IEEE Standards Association (IEEE‐SA) Standards Board. The IEEE develops its
standards through a consensus development process, approved by the American National Standards
Institute, which brings together volunteers representing varied viewpoints and interests to achieve
the final product. Volunteers are not necessarily members of the Institute and serve without
compensation. While the IEEE administers the process and establishes rules to promote fairness in
the consensus development process, the IEEE does not independently evaluate, test, or verify the
accuracy of any of the information contained in its standards.
Attention is drawn to the possibility that some of the elements of this document may be the subject
of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent
rights. Details of any patent rights identified during the development of the document will be in the
Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does
not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT),
see www.iso.org/iso/foreword.html.
ISO/IEC/IEEE 24748‐8 was prepared by the Software & Systems Engineering Standards Committee
of the IEEE Computer Society (as IEEE Std 15288.2) and drafted in accordance with its editorial
rules. It was adopted, under the “fast‐track procedure” defined in the Partner Standards
Development Organization cooperation agreement between ISO and IEEE, by Joint Technical
Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 7, Software and systems
engineering.
Any feedback or questions on this document should be directed to the user’s national standards
body. A complete listing of these bodies can be found at www.iso.org/members.html.
© IEEE 2015 – All rights reserved
iii

---------------------- Page: 3 ----------------------
IEEE Std 15288.2™-2014
IEEE Standard for Technical Reviews
and Audits on Defense Programs
Sponsor
Software & Systems Engineering Standards Committee
of the
IEEE Computer Society
Appro
...