ISO 16936-2:2005
(Main)Glass in building — Forced-entry security glazing — Part 2: Test and classification by repetitive impact of a hammer and axe at room temperature
Glass in building — Forced-entry security glazing — Part 2: Test and classification by repetitive impact of a hammer and axe at room temperature
ISO 16936-2:2005 specifies requirements and a mechanical test method for security glazing designed to resist actions of manual attack by delaying access of objects and/or persons to a protected space for a short period of time. ISO 16936-2:2005 classifies security glazing products into categories of resistance against repetitive impacts of a hammer and an axe. The categories of resistance have not been assigned to special applications. Glazing classification should be specified on an individual basis for every application. ISO 16936-2:2005 deals with mechanical resistance to manual attack only.
Verre dans la construction — Vitrages de sécurité contre infractions — Partie 2: Essai et classification par impact répété d'un marteau et d'une hache à température ambiante
General Information
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 16936-2
First edition
2005-07-01
Glass in building — Forced-entry security
glazing —
Part 2:
Test and classification by repetitive
impact of a hammer and axe at room
temperature
Verre dans la construction — Vitrages de sécurité contre infractions —
Partie 2: Essai et classification par impact répété d'un marteau et d'une
hache à température ambiante
Reference number
ISO 16936-2:2005(E)
©
ISO 2005
---------------------- Page: 1 ----------------------
ISO 16936-2:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
©
ii ISO 2005 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 16936-2:2005(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols (and abbreviated terms) . 2
5 Sampling . 2
6 Apparatus . 3
7 Required characteristics . 8
8 Test method . 8
9 Classification and designation . 12
10 Test report . 12
11 Marking . 12
Bibliography . 13
©
ISO 2005 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 16936-2:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.