ISO 16835:2014
(Main)Refractory products — Determination of thermal expansion
Refractory products — Determination of thermal expansion
ISO 16835:2014 specifies test methods for the thermal expansion of refractory products. It describes a method for determining the linear thermal expansion percentage, the linear thermal expansion curve, and the linear thermal expansion coefficient. ISO 16835:2014 includes the following three test methods for the thermal expansion of refractory products: a) a contact method with a cylindrical test piece; b) a contact method with a rod test piece; c) a non-contact method.
Produits réfractaires — Détermination de la dilatation thermique
L'ISO 16835:2014 spécifie les méthodes d'essai de la dilatation thermique des produits réfractaires. La présente Norme décrit une méthode de détermination du pourcentage de dilatation thermique linéique, de la courbe de dilatation thermique linéique et du coefficient de dilatation thermique linéique. L'ISO 16835:2014 comprend les trois méthodes d'essai suivantes de dilatation thermique de produits réfractaires: a) Méthode par contact avec éprouvette d'essai cylindrique. b) Méthode par contact avec éprouvette d'essai en forme de tige. c) Méthode sans contact.
General Information
Buy Standard
Standards Content (Sample)
DRAFT INTERNATIONAL STANDARD ISO/DIS 16835
ISO/TC 33 Secretariat: BSI
Voting begins on Voting terminates on
2012-11-20 2013-02-20
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Refractory products — Determination of thermal expansion
Produits réfractaires — Dosage de la dilatation thermique
ICS 81.080
To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
© International Organization for Standardization, 2012
---------------------- Page: 1 ----------------------
ISO/DIS 16835
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user’s country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2012 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/DIS 16835
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Contact method with cylindrical test piece .3
4.1 Principle .3
4.2 Apparatus.3
4.3 Test piece .8
4.4 Procedure.9
4.5 Calculation and drawing.10
5 Contact method with rod test piece .13
5.1 Principle .13
5.2 Apparatus, implement and reference sample .13
5.3 Test piece .16
5.4 Procedure.17
5.5 Calculation and drawing.
...
INTERNATIONAL ISO
STANDARD 16835
First edition
2014-04-01
Refractory products — Determination
of thermal expansion
Produits réfractaires — Dosage de la dilatation thermique
Reference number
ISO 16835:2014(E)
©
ISO 2014
---------------------- Page: 1 ----------------------
ISO 16835:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 16835:2014(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Contact method with cylindrical test piece . 3
4.1 Principle . 3
4.2 Apparatus . 3
4.3 Test piece . 8
4.4 Procedure .10
4.5 Calculation and drawing .10
5 Contact method with rod test piece .14
5.1 Principle .14
5.2 Apparatus, implement and reference sample .14
5.3 Test piece .17
5.4 Procedure .18
5.5 Calculation and drawing .19
6 Non-contact method.22
6.1 Principle .22
6.2 Procedure .23
6.3 Calculation and drawing a figure .
...
NORME ISO
INTERNATIONALE 16835
Première édition
2014-04-01
Produits réfractaires — Détermination
de la dilatation thermique
Refractory products — Determination of thermal expansion
Numéro de référence
ISO 16835:2014(F)
©
ISO 2014
---------------------- Page: 1 ----------------------
ISO 16835:2014(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2014
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2014 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 16835:2014(F)
Sommaire Page
Avant-propos . iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Méthode par contact avec éprouvette d’essai cylindrique . 3
4.1 Principe . 3
4.2 Appareillage . 3
4.2.1 Appareillage d'essai de dilatation thermique . 3
4.2.2 Four . 7
4.2.3 Détecteur de l'ampleur de déformation de l'éprouvette d'essai . 7
4.2.4 Appareillage de mesurage de la température . 8
4.2.5 Pieds à coulisse . 8
4.2.6 Echantillon de référence . 8
4.3 Eprouvette d'essai . 8
4.3.1 Forme de l'éprouvette d'essai . 8
4.3.2 Préparation de l'éprouvette d'essai . 9
4.4 Mode opératoire . 10
4.4.1 Mesurage de l’éprouvette d'essai . 10
4.4.2 Mesurage de l'échantillon de référence . 10
4.5 Calcul et tracé . 10
5 Méthode par contact avec éprouvette d'essai en forme de tige . 13
5.1 Principe . 13
5.2 Appareillage, équipements et échantillon de référence . 13
5.2.1 Appareillage d’essai de dilatation thermique . 13
5.2.2 Micromètre ou pieds à coulisse . 16
5.2.3 Echantillon de référence . 16
5.3 Eprouvette d’essai .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.