ISO 11513:2019

Gas cylinders — Refillable welded steel cylinders containing materials for sub-atmospheric gas packaging (excluding acetylene) — Design, construction, testing, use and periodic inspection

This document specifies minimum requirements for the material, design, construction, workmanship, examination and testing at manufacture of refillable welded steel cylinders for the sub-atmospheric pressure storage of liquefied and compressed gases. It only applies to the cylinders themselves, irrespective of the materials contained therein (e.g. adsorbents, media, materials and/or gases) and other related applications. The cylinders have a test pressure not greater than 42 bar and a water capacity from 0,5 l up to and including 12 l exposed to ambient temperatures for the purpose of facilitating the sub‑atmospheric pressure storage of liquefied and compressed gases as adsorbed gases. Minimum requirements for inspection at the time of fill and periodic inspection and testing are also specified.

Bouteilles à gaz — Bouteilles en acier soudées rechargeables contenant des matériaux pour le stockage des gaz à une pression sub-atmosphérique (à l'exclusion de l'acétylène) — Conception, fabrication, essais, utilisation et contrôle périodique

General Information

• Status: Published
• Publication Date: 19-Jun-2019
• ICS: 23.020.35 - Gas cylinders
• Technical Committee: ISO/TC 58/SC 3 - Cylinder design
• Drafting Committee: ISO/TC 58/SC 3 - Cylinder design
• Current Stage: 9020 - International Standard under periodical review
• Start Date: 15-Apr-2024
• Completion Date: 15-Apr-2024

Relations

• Consolidated By: ISO 15527:2022 - Plastics — Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) — Requirements and test methods
• Effective Date: 06-Jun-2022
• Revises: ISO 11513:2011 - Gas cylinders — Refillable welded steel cylinders containing materials for sub-atmospheric gas packaging (excluding acetylene) — Design, construction, testing, use and periodic inspection
• Effective Date: 17-Dec-2016

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11513
Second edition
2019-06
Gas cylinders — Refillable welded
steel cylinders containing materials
for sub-atmospheric gas packaging
(excluding acetylene) — Design,
construction, testing, use and periodic
inspection
Bouteilles à gaz — Bouteilles en acier soudées rechargeables
contenant des matériaux pour le stockage des gaz à une pression
sub-atmosphérique (à l'exclusion de l'acétylène) — Conception,
fabrication, essais, utilisation et contrôle périodique
Reference number
ISO 11513:2019(E)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 11513:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11513:2019(E)

Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and symbols . 2
3.1 Terms and definitions . 2
3.2 Symbols . 2
4 Inspection and testing . 3
5 Materials and stress relieving . 3
6 Design . 4
6.1 General . 4
6.2 Calculation of cylindrical wall thickness. 5
6.3 Design of cylinder ends. 5
6.3.1 General. 5
6.3.2 Design of base concave to pressure . 5
6.4 Minimum wall thickness . 6
6.5 Pressure relief device . 7
7 Construction and workmanship .
...