Dentistry — Coupling dimensions for handpiece connectors

ISO 3964:2016 specifies the coupling between handpieces and motors connected to dental units. ISO 3964:2016 specifies the nominal dimensions, tolerances and the extraction force of coupling systems for use between handpiece and motor which supply the handpiece with water, air and light and rotation energy.

Médecine bucco-dentaire — Dimensions d'accouplement pour pièces à main dentaires

ISO 3964:2016 spécifie l'accouplement entre les pièces à main et les moteurs connectés aux units dentaires. ISO 3964:2016 spécifie les dimensions nominales, les tolérances et la force d'extraction des systèmes d'accouplement utilisés entre la pièce à main et le moteur qui lui fournissent l'eau, l'air, la lumière et l'énergie de rotation.

General Information

Status
Published
Publication Date
30-Oct-2016
Current Stage
9093 - International Standard confirmed
Ref Project

Relations

Buy Standard

Standard
ISO 3964:2016 - Dentistry -- Coupling dimensions for handpiece connectors
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 3964:2016 - Médecine bucco-dentaire -- Dimensions d'accouplement pour pieces a main dentaires
French language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3964
Third edition
2016-11-01
Dentistry — Coupling dimensions for
handpiece connectors
Médecine bucco-dentaire — Dimensions d’accouplement pour pièces
à main dentaires
Reference number
ISO 3964:2016(E)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 3964:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3964:2016(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 1
5 Requirements . 2
5.1 General . 2
5.2 Dimensions . 2
5.3 Coupling force .10
6 Sampling .10
7 Test methods .10
7.1 Dimensions .10
7.2 Coupling force .11
© ISO 2016 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3964:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.
The committee responsible for this document is ISO/TC 106 Dentistry, Subcommittee SC 4 Dental
instruments.
This third edition cancels and replaces the second edition (ISO 3964:1982), which has been technically
revised with the following changes:
a) addition of definitions for “coupling dimension” and “coupling systems”;
b) addition of four types for “classification”;
c) additional types of coupling systems:
— with and without light supply;
— with internal and external supply of air and water (spray);
d) improved technical drawings.
iv © ISO 2016 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 3964:2016(E)
Dentistry — Coupling dimensions for handpiece
connectors
1 Scope
This International Standard specifies the coupling between handpieces and motors connected to
dental units.
This International Standard specifies the nominal dimensions, tolerances and the extraction force of
coupling systems for use between handpiece and motor which supply the handpiece with water, air and
light and rotation energy.
2 Normative
...

NORME ISO
INTERNATIONALE 3964
Troisième édition
2016-11-01
Médecine bucco-dentaire —
Dimensions d’accouplement pour
pièces à main dentaires
Dentistry — Coupling dimensions for handpiece connectors
Numéro de référence
ISO 3964:2016(F)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 3964:2016(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2016, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 3964:2016(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Classification . 1
5 Exigences . 2
5.1 Généralités . 2
5.2 Dimensions . 2
5.3 Force d’accouplement .10
6 Échantillonnage .10
7 Méthodes d’essai .11
7.1 Dimensions .11
7.2 Force d’accouplement .11
© ISO 2016 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 3964:2016(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à
l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes
de l’OMC concernant les obstacles techniques au commerce (OTC), voir le lien suivant: Avant-propos —
Informations supplémentaires.
Le comité chargé de l’élaboration du présent document est l’ISO/TC 106 Médecine bucco-dentaire, sous-
comité SC 4 Instruments dentaires.
Cette troisième édition annule et remplace la deuxième édition (ISO 3964:1982), qui a fait l’objet d’une
révision technique en vue d’apporter les modifications suivantes:
a) ajout des définitions pour «dimension d’accouplement» et «systèmes d’accouplement»;
b) ajout de quatre types pour «classification»;
c) types supplémentaires de systèmes d’accouplement:
— avec et sans dispositif d’éclairage;
— avec alimentation interne et externe en air et en eau (pulvérisés);
d) amélioration des dessins techniques.
iv © ISO 2016 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 3964:2016(F)
Médecine bucco-dentaire — Dimensions d’accouplement
pour pièces à main dentaires
1 Domaine d’application
La présente Norme internationale spécifie l’accouplement entre les pièces à main et les moteurs
connectés aux units dentaires.
Elle spécifie les dimensions nominales, les tolérances et la force d’extraction des systèmes
d’accouplement utilisés entre la pièce à main et le moteur qui lui fournissent l’eau, l’air, la lumière et
l’énergie de rotation.
2 Références normatives
Les documents ci-après, dans leur intégralité ou non, sont des références normatives indispensables à
l’application du présent document. Pour les références datées, seule l’édition citée s’applique. Pour les
références non datées, la dernière
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.