ISO 9022-2:2015/Amd 1:2023

Optics and photonics — Environmental test methods — Part 2: Cold, heat and humidity — Amendment 1

Optique et photonique — Méthodes d'essais d'environnement — Partie 2: Froid, chaleur et humidité — Amendement 1

General Information

• Status: Published
• Publication Date: 27-Jul-2023
• ICS: 37.020 - Optical equipment
• Technical Committee: ISO/TC 172/SC 1 - Fundamental standards
• Drafting Committee: ISO/TC 172/SC 1 - Fundamental standards
• Current Stage: 6060 - International Standard published
• Start Date: 28-Jul-2023
• Due Date: 01-Dec-2024
• Completion Date: 28-Jul-2023

Relations

• Amends: ISO 9022-2:2015 - Optics and photonics — Environmental test methods — Part 2: Cold, heat and humidity
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 9022-2
Third edition
2015-03-01
AMENDMENT 1
2023-07
Optics and photonics —
Environmental test methods —
Part 2:
Cold, heat and humidity
AMENDMENT 1
Optique et photonique — Méthodes d'essais d'environnement —
Partie 2: Froid, chaleur et humidité
AMENDEMENT 1
Reference number
ISO 9022-2:2015/Amd.1:2023(E)
© ISO 2023

---------------------- Page: 1 ----------------------
ISO 9022-2:2015/Amd.1:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 9022-2:2015/Amd.1:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information giv
...