ISO/IEC 11801-9910:2020

Information technology – Generic cabling for customer premises — Part 9910: Specifications for modular plug terminated link cabling

ISO/IEC TR 11801-9910:2020, which is a Technical Report, provides definitions for, and examples of, modular plug terminated link configurations. This document provides performance specifications for Classes D, E, EA, F, FA, I and II modular plug terminated links. Test methods are provided in Clause 8 and are specified in ISO/IEC 14763-4

Technologies de l'information — Câblage générique des locaux d'utilisateurs — Partie 9910: Titre manque

General Information

• Status: Published
• Publication Date: 22-Jun-2020
• ICS: 35.200 - Interface and interconnection equipment
• Technical Committee: ISO/IEC JTC 1/SC 25 - Interconnection of information technology equipment
• Drafting Committee: ISO/IEC JTC 1/SC 25 - Interconnection of information technology equipment
• Current Stage: 6060 - International Standard published
• Start Date: 23-Jun-2020
• Due Date: 22-Jun-2022
• Completion Date: 23-Jun-2020

Standards Content (Sample)

ISO/IEC TR 11801-9910
Edition 1.0 2020-06
TECHNICAL
REPORT

Information technology – Generic cabling for customer premises –
Part 9910: Specifications for modular plug terminated link cabling


ISO/IEC TR 11801-9910:2020-06(en)

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2020 ISO/IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about
ISO/IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address
below or your local IEC member National Committee for further information.


IEC Central Office Tel.: [phone]
3, rue de Varembé [e-mail]
CH-1211 Geneva 20 www.iec.ch
Switzerland

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have been
IEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.

need further assistance, please contact the Customer Service

Centre: [e-mail].

---------------------- Page: 2 ----------------------
ISO/IEC TR 11801-9910


Edition 1.0 2020-06




TECHNICAL



REPORT



















Information technology – Generic cabling for customer premises –

Part 9910: Specifications for modular plug terminated link cabling


























INTERNATIONAL

ELECTROTECHNICAL

COMMISSION






ICS 35.200 ISBN 978-2-8322-8492-6




  Warning! Make sure that you obtained this publication from an authorized distributor.

---------------------- Page: 3 ----------------------
– 2 – ISO/IEC TR 11801-9910:2020
© ISO/IEC 2020
CONTENTS
FOREWORD . 3
INTRODUCTION . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions, abbreviated terms and symbols . 5
3.1 Terms and definitions . 5
3.2 Abbreviated terms . 5
3.3 Symbols . 6
4 Specifications . 6
5 MPTL configuration . 6
6 Performance specifications . 7
6.1 General . 7
6.2 Return loss . 7
6.3 Insertion loss . 7
6.4 NEXT . 7
6.5 PS NEXT . 7
6.6 ACR-N . 7
6.7 PS ACR-N . 7
6.8 ACR-F . 7
6.9 PS ACR-F . 7
6.10 TCL . 8
6.11 ELTCTL . 8
6.12 Coupling attenuation . 8
6.13 Alien (exogenous) crosstalk . 8
6.14 Direct current loop resistance . 8
6.15 Direct current resistance unbalance . 8
6.16 Propagation delay . 8
6.17 Delay skew . 8
7 MPTL cabling performance . 8
7.1 General . 8
7.2 Reference performance testing . 8
7.3 Installation performance testing . 9
7.4 Installation performance testing of MPTLs. 9
8 Testing of MPTLs . 11
Bibliography . 12

Figure 1 – MPTL configurations . 6

Table 1 – Test regime for reference performance and installation performance –
MPTLs of Classes D, E, E F, F , I and II . 10
,
A A

---------------------- Page: 4 ----------------------
ISO/IEC TR 11801-9910:2020 – 3 –
© ISO/IEC 2020
INFORMATION TECHNOLOGY –
GENERIC CABLING FOR CUSTOMER PREMISES –

Part 9910: Specifications for modular plug terminated link cabling

FOREWORD
1) ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission)
form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC
participate in the development of International Standards through technical committees established by the
respective organization to deal with particular fields of technical activity. ISO and IEC technical committees
collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental,
in liaison with ISO and IEC, also take part in the work.
2) The formal decisions or agreements of IEC and ISO on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested IEC and ISO National bodies.
3) IEC and ISO documents have the form of recommendations for international use and are accepted by IEC and
ISO National bodies in that sense. While all reasonable efforts are made to ensure that the technical content of
IEC and ISO documents is accurate, IEC and ISO cannot be held responsible for the way in which they are used
or for any misinterpretation by any end user.
4) In order to promote international uniformity, IEC and ISO National bodies undertake to apply IEC and ISO
documents transparently to the maximum extent possible in their national and regional publications. Any
divergence between any IEC and ISO document and the corresponding national or regional publication shall be
clearly indicated in the latter.
5) IEC and ISO do not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC and ISO marks of conformity. IEC and ISO are not
responsible for any services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this document.
7) No liability shall attach to IEC and ISO or their directors, employees, servants or agents including individual
experts and members of its technical committees and IEC and ISO National bodies for any personal injury,
property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including
legal fees) and expenses arising out of the publication, use of, or reliance upon, this ISO/IEC document or any
other IEC and ISO documents.
8) Attention is drawn to the Normative references cited in this document. Use of the referenced publications is
indispensable for the correct application of this document.
9) Attention is drawn to the possibility that some of the elements of this ISO/IEC document may be the subject of
patent rights. IEC and ISO shall not be held responsible for identifying any or all such patent rights.
The main task of IEC and ISO technical committees is to prepare International Standards.
However, a technical committee may propose the publication of a Technical Report when it has
collected data of a different kind from that which is normally published as an International
Standard, for example "state of the art".
ISO/IEC TR 11801-9910, which is a Technical Report, was prepared by subcommittee 25:
Interconnection of information technology equipment, of ISO/IEC joint technical committee 1:
Information technology.
The list of all currently available parts of the ISO/IEC 11801 series, under the general title
Information technology – Generic cabling for customer premises, can be found on the IEC and
ISO websites.
The text of this Technical Report is based on the following documents:
DTR Report on voting
JTC1-SC25/2924/DTR JTC1-SC25/2941/RVDTR

Full information on the voting for the approval of this Technical Report can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 5 ----------------------
– 4 – ISO/IEC TR 11801-9910:2020
© ISO/IEC 2020
INTRODUCTION
This document provides definitions and examples of modular plug ter
...