Road vehicles — Test devices for target vehicles, vulnerable road users and other objects, for assessment of active safety functions — Part 1: Requirements for passenger vehicle rear-end targets

This document specifies performance requirements for surrogate targets used to assess the system detection and activation performance of active safety systems. This document specifies the properties of a vehicle target that will allow it to represent a passenger vehicle in terms of size, shape, reflection properties, etc. for testing purposes. The document addresses the detection requirements for a vehicle target in terms of sensing technologies commonly in use at the time of publication of this document, and where possible, anticipated future sensing technologies. It also addresses methodologies to verify the target response properties to these sensors, as well as performance requirements for the target carrier. This document specifies the properties of the vehicle target for simulation of rear-end scenarios, with overlap greater than 50 %. The specifications of vehicle targets in this document are intended to address current and anticipated test protocols related to safety critical events in which the subject vehicle approaches a stopped, braking or slower moving (target) vehicle from behind and in the forward path of the subject vehicle. This document does not address the test procedures in terms of speeds, positions, or timing of events. Performance criteria for the active safety system are also not addressed.

Véhicules routiers - Dispositifs d'essai pour véhicules cibles, usagers de la route vulnérables et autres objets, pour l'évaluation de fonctions de sécurité active — Partie 1: Exigences pour cibles d'arrière de véhicules particuliers

General Information

Status
Published
Publication Date
26-Nov-2018
Current Stage
9060 - Close of review
Start Date
04-Jun-2029
Ref Project

Buy Standard

Standard
ISO 19206-1:2018 - Road vehicles -- Test devices for target vehicles, vulnerable road users and other objects, for assessment of active safety functions
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 19206-1
First edition
2018-12
Road vehicles — Test devices for
target vehicles, vulnerable road users
and other objects, for assessment of
active safety functions —
Part 1:
Requirements for passenger vehicle
rear-end targets
Véhicules routiers - Dispositifs d'essai pour véhicules cibles, usagers de
la route vulnérables et autres objets, pour l'évaluation de fonctions de
sécurité active —
Partie 1: Exigences pour cibles d'arrière de véhicules particuliers
Reference number
ISO 19206-1:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 19206-1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 19206-1:2018(E)

Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviated terms . 2
5 Vehicle target specifications . 2
5.1 Vehicle classes and target applicability . 2
5.2 Reference dimensional measurements . 3
5.3 Safety considerations . 4
5.4 Repairability . 4
5.5 Environmental conditions . 4
6 Vehicle target response to sensing technologies . 4
6.1 General . 4
6.2 Optical requirements . 4
6.2.1 General. 4
6.2.2 Reference measurements . 4
6.2.3 Stability of dimensions for optical recognition . 5
6.2.4 Viewing
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.