Aircraft ducting and piping — Profile dimensions for flanges of V-band couplings

ISO 2563:2009 gives the profile dimensions of V-band couplings, and the associated inch-based aircraft ducting and piping for the following external flange profiles: lightweight solid profile; medium-weight solid profile; heavyweight solid profile; narrow sheet metal profile; wide sheet metal profile; wide solid profile; wide sheet metal to solid profile.

Canalisations et tuyauteries à bord des aéronefs — Dimensions d'encombrement des brides à section en V pour raccords

General Information

Status
Published
Publication Date
26-Aug-2009
Current Stage
9093 - International Standard confirmed
Completion Date
06-Nov-2020
Ref Project

Relations

Buy Standard

Standard
ISO 2563:2009 - Aircraft ducting and piping -- Profile dimensions for flanges of V-band couplings
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 2563
Second edition
2009-09-01

Aircraft ducting and piping — Profile
dimensions for flanges of V-band
couplings
Canalisations et tuyauteries à bord des aéronefs — Dimensions
d'encombrement des brides à section en V pour raccords




Reference number
ISO 2563:2009(E)
©
ISO 2009

---------------------- Page: 1 ----------------------
ISO 2563:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 2563:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 2563 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee
SC 10, Aerospace fluid systems and components.
This second edition cancels and replaces the first edition (ISO 2563:1974), which has been technically revised.

© ISO 2009 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 2563:2009(E)

Aircraft ducting and piping — Profile dimensions for flanges of
V-band couplings
1 Scope
This International Standard gives the profile dimensions of V-band couplings, and the associated inch-based
aircraft ducting and piping for the following external flange profiles:
⎯ lightweight solid profile;
⎯ medium-weight solid profile;
⎯ heavyweight solid profile;
⎯ narrow sheet metal profile;
⎯ wide sheet metal profile;
⎯ wide solid profile;
⎯ wide sheet metal to solid profile.
2 Dimensions
2.1 The profile dimensions of a mating pair of flanges of V-band couplings shall comply with Figures 1 to 7,
in accordance with the type of coupling required for the application. The dimensions are given in millimetres,
with inch equivalents in parentheses.
2.2 The design of joints is at the discretion of the user, but the joint design shall remain within the range of
the profiles given in this International Standard.
2.3 Flange halves are illustrated as being identical in the figures, but at the discretion of the user, the flange
faces can be asymmetric, allowing the creation of locating spigots and recesses or other locating features,
within the boundaries of the overall definition. The narrow and wide sheet metal flanges are identical. The
single wide sheet metal profile flange shown in Figure 7 should be mated with a single solid profile flange
shown in Figure 6.
2.4 The single flange end shown in Figure 7 may be machined on a pump or valve, which mates with
ducting.
© ISO 2009 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO 2563:2009(E)
Dimensions in millimetres (inches)

Key
1 tube outside diameter
a
Gauge.
b
Nominal.

Figure 1 — Lightweight solid flange profile
2 © ISO 2009 – All rights reserved

---------------------- Page: 5 ----------------------
ISO 2563:2009(E)
Table 1 — Dimensions for lightweight solid flange
Tube outside diameter Ø B
Ø A ± 0,25 (0,010)
a
DN  mm in mm in
1.000 38,3
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.