ISO 6469-3:2018/Amd 1:2020
(Amendment)Electrically propelled road vehicles — Safety specifications — Part 3: Electrical safety — Amendment 1: Withstand voltage test for electric power sources
Electrically propelled road vehicles — Safety specifications — Part 3: Electrical safety — Amendment 1: Withstand voltage test for electric power sources
Véhicules routiers électriques — Spécifications de sécurité — Partie 3: Sécurité électrique — Amendement 1: Essai de tension de tenue pour les sources d'alimentation électrique
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 6469-3
Third edition
2018-10
AMENDMENT 1
2020-03
Electrically propelled road vehicles —
Safety specifications —
Part 3:
Electrical safety
AMENDMENT 1: Withstand voltage test
for electric power sources
Véhicules routiers électriques — Spécifications de sécurité —
Partie 3: Sécurité électrique
AMENDEMENT 1: Essai de tension de tenue pour les sources
d'alimentation électrique
Reference number
ISO 6469-3:2018/Amd.1:2020(E)
©
ISO 2020
---------------------- Page: 1 ----------------------
ISO 6469-3:2018/Amd.1:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 6469-3:2018/Amd.1:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 22, Road Vehicles, Subcommittee SC 37,
Electrically propelled vehicles.
A list of all parts in the ISO 6469 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
© ISO 2020 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 6469-3:2018/Amd.1:2020(E)
Electrically propelled road vehicles — Safety
specifications —
Part 3:
Electrical safety
AMENDMENT 1: Withstand voltage test for electric power
sources
Clause 3
Add the following terminological entry:
3.37
electric power source
system that provides electric energy
EXAMPLE RESS, fuel cell system, photovoltaic system.
10.6.1
Add following text after the second paragraph:
Electric power sources, which can be de-energized, shall be de-energized and included into the balance
of the electric circuit.
Electric power sources, which are not part of the balance of the electric circuit shall be tested according
to 10.7.
10.7
Add the following subclauses after 10.6 and before the Bibliography:
10.7 Withstand voltage test for electric power sources which are not de-energized
10.7.1 General
This test is intended to demonstrate the adequacy of the protection measures to isolate live parts of
voltage class B electric circuits.
It applies to voltage class B electric circuits of electric power sources that are not conductively
connected to a voltage class A electric circuit or to the electric chassis.
The test may be performed at the vehicle level at the discretion of the vehicle manufacturer.
© ISO 2020 – All rights reserved 1
---------------------- Page: 4 ----------------------
ISO 6469-3:2018/Amd.1:2020(E)
For this test, device under test (DUT) refers to a voltage class B electric power source that cannot be
de-energized.
The voltage withstand test for the components of DUT (e.g. control unit, contactor) can be performed
separately unless it affects the test results. For components of the DUT which are de-ener
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.