ISO 16132:2024

Ductile iron pipes and fittings — Seal coats for cement mortar linings

This document specifies the requirements for seal coatings for factory application to the surfaces of cement mortar linings, which are factory applied to the interior of ductile iron pipes and fittings. It provides the performance requirements for short-term sealing efficiency, long-term durability and cyclic pressure, as well as the routine testing requirements for visual appearance, coating thickness and adhesion. This document is applicable to products for potable and irrigation water and for other applications as per agreement between manufacturer and customer.

Tuyaux et raccords en fonte ductile — Seal coats pour les revêtements de mortier de ciment

General Information

• Status: Published
• Publication Date: 07-Mar-2024
• ICS: 23.040.10 - Iron and steel pipes
• ICS: 77.140.75 - Steel pipes and tubes for specific use
• Technical Committee: ISO/TC 5/SC 2 - Cast iron pipes, fittings and their joints
• Drafting Committee: ISO/TC 5/SC 2 - Cast iron pipes, fittings and their joints
• Current Stage: 6060 - International Standard published
• Start Date: 08-Mar-2024
• Due Date: 05-Feb-2024
• Completion Date: 08-Mar-2024

Relations

• Revises: ISO 16132:2016 - Ductile iron pipes and fittings — Seal coats for cement mortar linings
• Effective Date: 06-Aug-2022

Standards Content (Sample)

International
Standard
ISO 16132
Third edition
Ductile iron pipes and fittings —
2024-03
Seal coats for cement mortar linings
Tuyaux et raccords en fonte ductile — Seal coats pour les
revêtements de mortier de ciment
Reference number
ISO 16132:2024(en) © ISO 2024

---------------------- Page: 1 ----------------------
ISO 16132:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland

© ISO 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO 16132:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Materials in contact with water intended for human consumption . 2
5 Performance test requirements . 2
5.1 Short-term sealing efficiency . . .2
5.2 Long-term sealing efficiency .2
5.3 Cyclic pressure .3
6 Routine test requirements . 3
6.1 General .3
6.2 Visual appearance .3
6.3 Coating thickness .3
6.4 Adhesion .3
7 Marking . . 4
Annex A (normative) Short-term sealing efficiency . 5
Annex B (normative) Long-term sealing efficiency . 8
A
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 16132
ISO/TC 5/SC 2
Ductile iron pipes and fittings — Seal
Secretariat: AFNOR
coats for cement mortar linings
Voting begins on:
2023-12-14
Tuyaux et raccords en fonte ductile — Seal coats pour les revêtements
de mortier de ciment
Voting terminates on:
2024-02-08
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 16132:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 1 ----------------------
ISO/FDIS 16132:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 16132
ISO/TC 5/SC 2
Ductile iron pipes and fittings — Seal
Secretariat: AFNOR
coats for cement mortar linings
Voting begins on:
Tuyaux et raccords en fonte ductile — Seal coats pour les revêtements
de mortier de ciment
Voting terminates on:
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: [phone]
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: [e-mail]
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/FDIS 16132:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
  © ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 2 ----------------------
ISO/FDIS 16132:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Materials in contact with water intended for human consumption .2
5 Performance test requirements . 2
5.1 Short-term sealing efficiency . . . 2
5.2 Long-term sealing efficiency . 2
5.3 Cyclic pressure . 3
6 Routine test requirements . 3
6.1 General . 3
6.2 Vi
...

ISO/FDIS 16132:2023(E)
Date: 2023--10-27
ISO/TC 5/SC 2/WG 24
Secretariat: AFNOR
Date: 2023-11-30
Ductile iron pipes and fittings — Seal coats for cement mortar
linings
Tuyaux et raccords en fonte ductile — Seal coats pour les revêtements de mortier de ciment
FDIS stage

---------------------- Page: 1 ----------------------
ISO/FDIS 16132:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this
publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,
including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can
be requested from either ISO at the address below or ISO'sISO’s member body in the country of the requester.
ISO Copyright Officecopyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Email: [e-mail]
E-mail: [e-mail]
Website: www.iso.orgwww.iso.org
Published in Switzerland.
ii © ISO 2023 – All rights reserved
ii © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 16132:2023(E)
Contents Page
Foreword . vi
Introduction .vi i
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Materials in contact with water intended for human consumption . 2
5 Performance test requirements . 2
5.1 Short-term sealing efficiency . 2
5.2 Long-term sealing efficiency . 2
5.3 Cyclic pressure . 3
6 Routine test requirements . 3
6.1 General . 3
6.2 Visual appearance . 3
6.3 Coating thickness . 4
6.4 Adhesion . 4
7 Marking . 4
Annex A (normative) Short-term sealing efficiency . 5
A.1 Principle . 5
A.2 Materials . 5
A.3 Apparatus . 5
A.4 Preparation of test samples .
...