Rolling bearings — Noise testing of rolling bearing greases — Part 4: Test and evaluation method NQ

This document specifies the testing and evaluation method of rolling bearing grease noise in accordance with the method NQ.

Roulements — Essais de bruit de graisse pour roulement — Partie 4: Méthode d’essai et interpretation NQ

General Information

Status
Published
Publication Date
12-Jul-2020
Technical Committee
Drafting Committee
Current Stage
6060 - International Standard published
Start Date
13-Jul-2020
Due Date
19-Oct-2020
Completion Date
13-Jul-2020
Ref Project

Buy Standard

Standard
ISO 21250-4:2020 - Rolling bearings -- Noise testing of rolling bearing greases
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 21250-4 - Rolling bearings -- Noise testing of rolling bearing greases
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 21250-4
First edition
2020-07
Rolling bearings — Noise testing of
rolling bearing greases —
Part 4:
Test and evaluation method NQ
Roulements — Essais de bruit de graisse pour roulement —
Partie 4: Méthode d’essai et interpretation NQ
Reference number
ISO 21250-4:2020(E)
©
ISO 2020

---------------------- Page: 1 ----------------------
ISO 21250-4:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 21250-4:2020(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols, abbreviated terms and subscripts . 2
5 Calculation method . 2
5.1 Signal processing. 2
5.2 Peak detection . 2
6 Test method NQ . 4
6.1 Measuring principle . 4
6.2 Testing procedure . 4
7 Evaluation of results . 5
Annex A (informative) Test machine . 6
Annex B (informative) Calibration . 9
Bibliography .10
© ISO 2020 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 21250-4:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 4, Rolling bearings.
A list of all parts in the ISO 21250 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 21250-4:2020(E)

Introduction
The rolling bearing life theory emphasizes the use of pure and homogeneous lubricants as essential for
a long bearing service life. The lubrication of rolling bearings is described in several national standards.
[4]
The GfT worksheet 3 contains theoretical and practical knowledge of rolling bearing lubrication.
Grease lubrication is the most common type of rolling bearing lubrication. The purity grade of rolling
bearing grease is influenced by thickeners, base oils, additives and solid lubricant additives as well
as the manufacturing process and is reflected in the running noise. Therefore, noise testing of rolling
bearing greases is recommended.
In addition, grease noise testing in accordance with this document allows the grease manufacturers
to develop low-noise lubricants with better damping properties. This document can also support the
rolling bearing manufacturers and end-users in the selection of low-noise grease with better damping
properties.
This document covers requirements for the testing assembly and the test machine of method NQ to
determine and assess the noise characteristics of rolling bearing grease jointly with ISO 21250-1,
ISO 21250-2 and ISO 21250-3.
© ISO 2020 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 21250-4:2020(E)
Rolling bearings — Noise testing of rolling bearing
greases —
Part 4:
Test and evaluation method NQ
1 Scope
This document specifies the testing and evaluation method of rolling bearing grease noise in accordance
with the method NQ.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 492, Rolling bearings — Radial bearings — Geometrical product specifications (GPS) and tolerance values
ISO 5593, Rolling bearings — Vocabulary
ISO 15242-1:2015, Rolling bearings — Measuring methods for vibration — Part 1: Fundamentals
ISO 15242-2:2015, Rolling bearings — Measuring methods for vibration — Part 2: Radial ball bearings
with cylindrical bore and outside surface
ISO 21250-1:2020, Rolling bearings — Noise testing of rolling bearing greases — Part 1: Basic principles,
testing assembly and test machine
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5593, ISO 15242-1, ISO 21250-1
and the following apply.
ISO and IEC maintain terminological databases
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 21250-4
ISO/TC 4
Rolling bearings — Noise testing of
Secretariat: SIS
rolling bearing greases —
Voting begins on:
2020-04-06
Part 4:
Voting terminates on:
Test and evaluation method NQ
2020-06-01
Roulements — Essais de bruit de graisse pour roulement —
Partie 4: Méthode d’essai et interpretation NQ
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 21250-4:2020(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2020

---------------------- Page: 1 ----------------------
ISO/FDIS 21250-4:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 21250-4:2020(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols, abbreviated terms and subscripts . 2
5 Calculation method . 2
5.1 Signal processing. 2
5.2 Peak detection . 2
6 Test method NQ . 4
6.1 Measuring principle . 4
6.2 Testing procedure . 4
7 Evaluation of results . 5
Annex A (informative) Test machine . 6
Annex B (informative) Calibration . 9
Bibliography .10
© ISO 2020 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/FDIS 21250-4:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 4, Rolling bearings.
A list of all parts in the ISO 21250 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/FDIS 21250-4:2020(E)

Introduction
The rolling bearing life theory emphasizes the use of pure and homogeneous lubricants as essential for
a long bearing service life. The lubrication of rolling bearings is described in several national standards.
[4]
The GfT worksheet 3 contains theoretical and practical knowledge of rolling bearing lubrication.
Grease lubrication is the most common type of rolling bearing lubrication. The purity grade of rolling
bearing grease is influenced by thickeners, base oils, additives and solid lubricant additives as well
as the manufacturing process and is reflected in the running noise. Therefore, noise testing of rolling
bearing greases is recommended.
In addition, grease noise testing in accordance with this document allows the grease manufacturers
to develop low-noise lubricants with better damping properties. This document can also support the
rolling bearing manufacturers and end-users in the selection of low-noise grease with better damping
properties.
This document covers requirements for the testing assembly and the test machine of method NQ to
determine and assess the noise characteristics of rolling bearing grease jointly with ISO 21250-1,
ISO 21250-2 and ISO 21250-3.
© ISO 2020 – All rights reserved v

---------------------- Page: 5 ----------------------
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 21250-4:2020(E)
Rolling bearings — Noise testing of rolling bearing
greases —
Part 4:
Test and evaluation method NQ
1 Scope
This document specifies the testing and evaluation method of rolling bearing grease noise in accordance
with the method NQ.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 5593, Rolling bearings — Vocabulary
ISO 15242-1:2015, Rolling bearings — Measuring methods for vibration — Part 1: Fundamentals
ISO 15242-2:2015, Rolling bearings — Measuring methods for vibration — Part 2: Radial ball bearings
with cylindrical bore and outside surface
ISO 21250-1:—, Rolling bearings — Noise testing of rolling bearing greases — Part 1: Basic principles,
testing assembly, test machine
3 Te
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.