Building and civil engineering sealants — Determination of the degree of cure — Part 2: Build-up of tensile and adhesion properties in test joint specimens

This document specifies a method for the determination of the degree of cure of one- and multi-component sealants used in joints as indicated by the build-up of the tensile and adhesion properties in test joint specimens during cure.

Titre manque — Partie 2: Titre manque

General Information

Status
Published
Publication Date
02-May-2021
Current Stage
6060 - International Standard published
Start Date
03-May-2021
Due Date
17-May-2022
Completion Date
03-May-2021
Ref Project

Buy Standard

Standard
ISO 24068-2:2021 - Building and civil engineering sealants -- Determination of the degree of cure
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/PRF 24068-2:Version 06-mar-2021 - Building and civil engineering sealants -- Determination of the degree of cure
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 24068-2
First edition
2021-05
Building and civil engineering
sealants — Determination of the
degree of cure —
Part 2:
Build-up of tensile and adhesion
properties in test joint specimens
Reference number
ISO 24068-2:2021(E)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO 24068-2:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 24068-2:2021(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus and materials. 2
6 Preparation of test specimen . 4
7 Conditioning of test and reference specimens . 4
7.1 Conditioning of test specimens . 4
7.2 Conditioning of reference specimens . 4
7.2.1 General. 4
7.2.2 Method A . 4
7.2.3 Method B . 5
8 Test procedure . 5
9 Calculation and expression of test result . 5
9.1 Tensile stress (secant modulus) . 5
9.2 Tensile strength . 6
9.3 Degree of cure . 6
9.4 Rounding of results . 6
10 Test report . 6
© ISO 2021 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 24068-2:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 59, Buildings and civil engineering works,
Subcommittee SC 8, Sealants.
A list of all parts in the ISO 24068 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 24068-2:2021(E)
Building and civil engineering sealants — Determination of
the degree of cure —
Part 2:
Build-up of tensile and adhesion properties in test joint
specimens
1 Scope
This document specifies a method for the determination of the degree of cure of one- and multi-
component sealants used in joints as indicated by the build-up of the tensile and adhesion properties in
test joint specimens during cure.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 6927, Building and civil engineering sealants — Vocabulary
ISO 8339, Building construction — Sealants — Determination of tensile properties (Extension to break)
ISO 13640, Buildings and civil engineering works — Sealants — Specifications for test substrates
ISO 80000-1:2009, Quantities and units — Part 1: General
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6927 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
4 Principle
The degree of cure of joint-shaped test specimen of a (ambient temperature curing) sealant is
determined as the ratio between the value of engineering tensile stress (secant modulus) and/or
tensile strength at any time during cure and the corresponding value measured after a reference cure
period (conditioning A or B or any other reference cure period or conditions as agreed by the parties
concerned).
© ISO 2021 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 24068-2:2021(E)

5 Apparatus and materials
5.1 Substrate supports, made of substrate materials as defined in ISO 13640, to be selected from
mortar and/or anodized aluminium and/or glass for the preparation of substrate pieces. Other substrate
materials may be used as agreed by the parties concerned.
For each test specimen, two substrate supports of the same material are required with a cross-section
of dimensions as defined ISO 8339 (see Figures 1 and 2). Test substrates of other dimensions may be
used. In this case, the dimensions of the sealant bead and the area of adhesion shall be the same as
those defined in ISO 8339.
Dimensions in millimetres
Key
1 mortar substrates
2 sealant
3 spacer
Figure 1 — Test specimen with mortar substrates
...

INTERNATIONAL ISO
STANDARD 24068-2
First edition
Building and civil engineering
sealants — Determination of the
degree of cure —
Part 2:
Build-up of tensile and adhesion
properties in test joint specimens
PROOF/ÉPREUVE
Reference number
ISO 24068-2:2021(E)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO 24068-2:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii PROOF/ÉPREUVE © ISO 2021 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 24068-2:2021(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus and materials. 2
6 Preparation of test specimen . 4
7 Conditioning of test and reference specimens . 4
7.1 Conditioning of test specimens . 4
7.2 Conditioning of reference specimens . 4
7.2.1 General. 4
7.2.2 Method A . 4
7.2.3 Method B . 5
8 Test procedure . 5
9 Calculation and expression of test result . 5
9.1 Tensile stress (secant modulus) . 5
9.2 Tensile strength . 6
9.3 Degree of cure . 6
9.4 Rounding of results . 6
10 Test report . 6
© ISO 2021 – All rights reserved PROOF/ÉPREUVE iii

---------------------- Page: 3 ----------------------
ISO 24068-2:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 59, Buildings and civil engineering works,
Subcommittee SC 8, Sealants.
A list of all parts in the ISO 24068 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv PROOF/ÉPREUVE © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 24068-2:2021(E)
Building and civil engineering sealants — Determination of
the degree of cure —
Part 2:
Build-up of tensile and adhesion properties in test joint
specimens
1 Scope
This document specifies a method for the determination of the degree of cure of one- and multi-
component sealants used in joint as indicated by the build-up of the tensile and adhesion properties in
test joint specimens during cure.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 6927, Buildings and civil engineering works — Sealants — Vocabulary
ISO 8339, Building construction — Sealants — Determination of tensile properties (Extension to break)
ISO 13640, Buildings and civil engineering works — Sealants — Specifications for test substrates
ISO 80000-1:2009, Quantities and units — Part 1: General
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6927 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
4 Principle
The degree of cure of joint-shaped test specimen of a (ambient temperature curing) sealant is
determined as the ratio between the value of engineering tensile stress (secant modulus) and/or
tensile strength at any time during cure and the corresponding value measured after a reference cure
period (conditioning A or B or any other reference cure period or conditions as agreed by the parties
concerned).
© ISO 2021 – All rights reserved PROOF/ÉPREUVE 1

---------------------- Page: 5 ----------------------
ISO 24068-2:2021(E)

5 Apparatus and materials
5.1 Substrate supports, made of substrate materials as defined in ISO 13640, to be selected from
mortar and/or anodized aluminium and/or glass for the preparation of substrate pieces. Other substrate
materials may be used as agreed by the parties concerned.
For each test specimen, two substrate supports of the same material are required with a cross-section
of dimensions as defined ISO 8339 (see Figures 1 and 2). Test substrates of other dimensions may be
used. In this case, the dimensions of the sealant bead and the area of adhesion shall be the same as
those defined in ISO 8339.
Dimensions in millimetres
Key
1 mortar substrates
2 sealant
3 spacer
Figure 1 — Test specimen with mortar substrates
2 PROOF/ÉPRE
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.