Mopeds — Measurement method for gaseous exhaust emissions and fuel consumption — Part 2: Test cycles and specific test conditions

This part of ISO 6855 defines test cycles for measurement for gaseous exhaust emissions from mopeds, as well as for determining the fuel consumption of mopeds as defined in ISO 3833, equipped with a spark ignition engine (four-stroke engine, two-stroke engine or rotary piston engine).

Cyclomoteurs — Méthode de mesure des émissions de gaz polluants et de consommation de combustible — Partie 2: Cyclomoteurs d'essai et conditions d'essai spécifiques

General Information

Status
Published
Publication Date
19-Sep-2012
Current Stage
9093 - International Standard confirmed
Completion Date
24-Oct-2023
Ref Project

Relations

Buy Standard

Standard
ISO 6855-2:2012 - Mopeds -- Measurement method for gaseous exhaust emissions and fuel consumption
English language
15 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6855-2
First edition
2012-09-15
Mopeds — Measurement method for
gaseous exhaust emissions and fuel
consumption —
Part 2:
Test cycles and specific test conditions
Cyclomoteurs — Méthode de mesure des émissions de gaz polluants et
de consommation de combustible —
Partie 2: Cyclomoteurs d’essai et conditions d’essai spécifiques
Reference number
ISO 6855-2:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 6855-2:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the
address below or ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6855-2:2012(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Test cycle . 1
3.1 Introduction . 1
3.2 Type 1 test . 1
3.3 Type 2 test . 5
4 Presentation of results . 6
Annex A (normative) Presentation of results for gaseous exhaust emissions .7
Annex B (normative) Presentation of results of fuel consumption .11
Bibliography .15
© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6855-2:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for i
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.