Aircraft — Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehicle — Part 1: Main deck doors

ISO 7718-1:2016 specifies minimum requirements for dimensions and unobstructed space around main deck passenger doors of future types of civil-passenger transport aircraft when they are intended to be compatible with the thousands of passenger boarding bridges and passenger transfer vehicles existing, or being planned, in airports worldwide. ISO 7718-1:2016 is not applicable to existing models of civil transport aircraft, or derivative models with entry into service up to year 2000 with the same fuselage, for which the aircraft-mating section of passenger boarding bridges or passenger transfer vehicles is expected to be compatible with ISO 16004. It is not the intent of this document to restrict in any way the basic design of any future types of civil-passenger transport aircraft. However, it aims at clarifying, for aircraft-design engineers, the design characteristics which would make it difficult or impossible for a new type of aircraft to adequately connect with existing airport passenger boarding bridges or passenger transfer vehicles. If basic aircraft-design requirements impose on a future model certain dimensional characteristics not complying with this document, note that: - either alternative methods of embarking/disembarking passengers will need to be implemented, such as integral aircraft stairs, etc.; - or existing passenger boarding bridges and/or passenger transfer vehicles in the airports where such a new type of aircraft is to operate will require some degree of modification/reworking; - or additional interface devices/equipment will be required in order to connect such a new type of aircraft with existing passenger boarding bridges and passenger transfer vehicles. Each case results in increased aircraft-handling constraints and operating cost.

Aéronefs — Exigences d'interface des portes passagers pour accouplement d'une passerelle passagers ou de véhicules de transfert de passagers — Partie 1: Portes de pont principal

General Information

Status
Published
Publication Date
11-Dec-2016
Current Stage
9092 - International Standard to be revised
Completion Date
01-Feb-2024
Ref Project

Relations

Buy Standard

Standard
ISO 7718-1:2016 - Aircraft -- Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehicle
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 7718-1
Second edition
2016-12-15
Aircraft — Passenger doors interface
requirements for connection of
passenger boarding bridge or
passenger transfer vehicle —
Part 1:
Main deck doors
Aéronefs — Exigences d’interface des portes passagers pour
accouplement d’une passerelle passagers ou de véhicules de transfert
de passagers —
Partie 1: Portes de pont principal
Reference number
ISO 7718-1:2016(E)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 7718-1:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 7718-1:2016(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 2
4.1 Minimum unobstructed space . 2
4.2 Minimum radius of the fuselage. 2
4.3 Door-sill height . 2
© ISO 2016 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 7718-1:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.