Road vehicles — Compressed gaseous hydrogen (CGH2) and hydrogen/natural gas blends fuel system components — Part 1: General requirements and definitions

ISO 12619-1:2014 specifies general requirements and definitions of compressed gaseous hydrogen (CGH2) and hydrogen/natural gas blends fuel system components, intended for use on the types of motor vehicles defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and markings. ISO 12619-1:2014 is applicable to vehicles using CGH2 in accordance with ISO 14687-1 or ISO 14687-2 and hydrogen/natural gas blends using natural gas in accordance with ISO 15403-1 and ISO/TR 15403-2. It is not applicable to the following: -liquefied hydrogen (LH2) fuel system components; -fuel containers; -stationary gas engines; -container mounting hardware; -electronic fuel management; -refuelling receptacles.

Véhicules routiers — Composants des circuits d'alimentation pour hydrogène gazeux comprimé (CGH2) et mélanges de gaz naturel et hydrogène — Partie 1: Exigences générales et définitions

General Information

Status
Published
Publication Date
10-Jun-2014
Current Stage
9093 - International Standard confirmed
Completion Date
12-Jul-2023
Ref Project

Buy Standard

Standard
ISO 12619-1:2014 - Road vehicles -- Compressed gaseous hydrogen (CGH2) and hydrogen/natural gas blends fuel system components
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 12619-1:2014 - Road vehicles -- Compressed gaseous hydrogen (CGH2) and hydrogen/natural gas blends fuel system components
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 12619-1
First edition
2014-06-15
Road vehicles — Compressed gaseous
hydrogen (CGH2) and hydrogen/
natural gas blend fuel system
components —
Part 1:
General requirements and definitions
Véhicules routiers — Composants des circuits d’alimentation pour
hydrogène gazeux comprimé (CGH2) et mélanges de gaz naturel et
hydrogène —
Partie 1: Exigences générales et définitions
Reference number
ISO 12619-1:2014(E)
©
ISO 2014

---------------------- Page: 1 ----------------------
ISO 12619-1:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 12619-1:2014(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Construction and assembly . 4
5 Electrical equipment and wiring . 5
6 Instructions . 5
7 Marking . 6
Bibliography . 8
© ISO 2014 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 12619-1:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 22, Road vehicles, Subcommittee SC 25, Vehicles
using gaseous fuels.
ISO 12619 consists of the following parts, under the general title Road vehicles — Compressed gaseous
hydrogen (CGH2) and hydrogen/natural gas blends fuel system components:
— Part 1: General requirements and definitions
— Part 2: Performance and general test methods
— Part 3: Pressure regulator
iv © ISO 2014 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 12619-1:2014(E)
Road vehicles — Compressed gaseous hydrogen
(CGH2) and hydrogen/natural gas blend fuel system
components —
Part 1:
General requirements and definitions
1 Scope
This part of ISO 12619 specifies general requirements and definitions of compressed gaseous hydrogen
(CGH2) and hydrogen/natural gas blends fuel system components, intended for use on the types of motor
vehicles defined in ISO 3833. It also provides general design principles and specifies requirements for
instructions and markings.
This part of ISO 12619 is applicable to vehicles using CGH2 in accordance with ISO 14687-1 or ISO 14687-2
and hydrogen/natural gas blends using natural gas in accordance with ISO 15403-1 and ISO/TR 15403-
2. It is not applicable to the following:
— liquefied hydrogen (LH2) fuel system components;
— fuel containers;
— stationary gas engines;
— container mounting hardware;
— electronic fuel management;
— refuelling receptacles.
NOTE 1 It is recognized that miscellaneous components not specifically covered herein can be examined to
meet the criteria of this part of ISO 12619 and tested according to the appropriate functional tests.
NOTE 2 All references to pressure in this part of ISO 12619 are to be considered gauge pressures unless
otherwise specified.
NOTE 3 This part of ISO 12619 may not apply to fuel cell vehicles in compliance with international regulations.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 6722-1, Road vehicles — 60 V and 600 V single-core cables — Part 1: Dimensions, test methods and
requirements for copper conductor cables
ISO 6722-2, Road vehicles — 60 V and 600 V single-core cables — Part 2: Dimensions, test methods and
requirements for aluminium conductor cables
ISO 12619-2, Road vehicles — Compressed gaseous hydrogen (CGH2) and hydrogen/natural gas blend fuel
system components — Part 2: Performance and general test methods
© ISO 2014 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 12619-1:2014(E)

ISO 14687-1, Hydrogen fuel — Product specification — Part 1: All applications except proton exchange
membrane (PEM) fuel cell for road vehicles
ISO 14687-2, Hydrogen fuel — Product specification — Part 2: Proton exchange membrane (PEM) fuel cell
applications for road vehicles
ISO 15403-1, Natural gas — Natural gas for use as a compressed fuel for vehicles — Part 1: Designation of
the quality
ISO/TR 15403-2, Natural gas — Natural gas for use as a compressed fuel for vehicles — Part 2: Specification
of the quality
1)
ISO 16380 , Road vehicles — Blended fuels refuelling connector
ISO 17268, Gaseous hydrogen land vehicle refuelling connection devices
3 Terms and definitions
3.1
agent
person or organization responsible for holding the compliance certificate
3.2
burst pressure
pressure which causes structural failure of the component and consequential inability of the component
to retain hydrogen or hydrogen/natural gas blends
3.3
compressed gaseous hydrogen
CGH2
gaseous hydrogen which has been compressed and stored for use as a vehicle fuel
3.4
filter
component that is intended to remove contaminants from the gas stream
3.5
flexible fuel line
flexible tubing or hose through which gaseous hydrogen or hydrogen/natural gas blend flows
3.6
fitting
connector used in joining a piping, tubing, or hose system
3.7
fuel cell gas injector
device used for introducing gas into the fuel cell
3.8
gas air mixer
device for mixing the gaseous fuel and intake air for the engine
3.9
gas flow adjuster
gas flow restricting device that is installed downstream of a pressure regulator for controlling gas
3.10
gas injector
device for introducing gaseous fuel into the engine or associated intake system
1) To be published.
2 © ISO 2014 – All rights reserved

---------------------- Page: 6 ----------------------
ISO 12619-1:2014(E)

3.11
gas tight housing
device which vents gas leakage to outside the vehicle including the gas ventilation hose, the clear opening
2
of which is at least 450 mm
...

DRAFT INTERNATIONAL STANDARD ISO/DIS 12619-1
ISO/TC 22/SC 25 Secretariat: UNI
Voting begins on Voting terminates on

2012-01-06 2012-06-06
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION    МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ    ORGANISATION INTERNATIONALE DE NORMALISATION


Road vehicles — Compressed Gaseous Hydrogen (CGH2) and
Hydrogen/Natural Gas blend fuel system components —
Part 1:
General requirements and definitions
Véhicules routiers — Composants des circuits d'alimentation pour hydrogène gazeux comprimé (CGH2) et
mélanges de gaz naturel et hydrogène —
Partie 1: Exigences générales et définitions
ICS 43.060.40








In accordance with the provisions of Council Resolution 15/1993 this document is circulated in
the English language only.
Conformément aux dispositions de la Résolution du Conseil 15/1993, ce document est distribué
en version anglaise seulement.

To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.



THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME
STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©  International Organization for Standardization, 2012

---------------------- Page: 1 ----------------------
ISO/DIS 12619-1

Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user’s country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.

ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DIS 12619-1

Contents Page
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
3.1 Valve . 2
3.1.1 manual valve . 2
3.1.2 automatic valve . 2
3.1.3 automatic cylinder valve . 2
3.1.4 check valve . 2
3.1.5 excess flow valve . 2
3.1.6 manual cylinder valve . 2
3.1.7 pressure relief valve PRV . 3
3.1.8 service valve . 3
3.2 compressed gaseous hydrogen CGH2 . 3
3.3 hydrogen blend . 3
3.4 filter . 3
3.5 fitting . 3
3.6 flexible fuel line . 3
3.7 gas-air mixer . 3
3.8 gas flow adjuster . 3
3.9 gas tight housing . 3
3.10 pressure indicator . 4
3.11 pressure regulator . 4
3.12 pressure relief device PRD . 4
3.13 rigid fuel line . 4
3.14 service pressure . 4
3.15 test pressure . 4
3.16 working pressure . 4
3.17 burst pressure . 4
3.18 gas injector . 4
3.19 fuel cell gas injector . 5
4 Construction and assembly . 5
5 Electrical equipment and wiring . 6
6 Instructions . 6
7 Marking . 7

© ISO 2011 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/DIS 12619-1

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12619-1 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 25, Road
vehicles using gaseous fuels.
ISO 12619 consists of the following parts, under the general title Road vehicles — Compressed Gaseous
Hydrogen (CGH2) and Hydrogen/methane blends fuel system components:
 Part 1: General requirements and definitions
 Part 2: Performance and general test methods
 Part 3: Pressure regulator

iv © ISO 2011 – All rights reserved

---------------------- Page: 4 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 12619-1

Road vehicles — Compressed Gaseous Hydrogen (CGH2) and
Hydrogen/Natural Gas blends fuel system components —
Part 1: General requirements and definitions
1 Scope
This Standard specifies general requirements and definitions of Compressed Gaseous Hydrogen (CGH2) and
Hydrogen/Natural Gas blends fuel system components, intended for use on the types of motor vehicles
defined in ISO 3833. It also provide general design principles and specifies requirements for instructions and
markings.
It is applicable to vehicles using Compressed Gaseous Hydrogen (CGH2) in accordance with ISO 14687 and
Hydrogen/Natural Gas blends. It is not applicable to the following:
a) liquefied hydrogen (LH2) fuel system components;
b) fuel containers;
c) stationary gas engines;
d) container mounting hardware;
e) electronic fuel management;
f) refuelling receptacles.
NOTE 1 It is recognized that miscellaneous components not specifically covered herein can be examined to meet the
criteria of this Standard and tested according to the appropriate f
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.