Connectors for electrical and electronic equipment - Product requirements - Part 3-124: Rectangular connectors - Detail specification for 10-way, shielded, free and fixed connectors for I/O and data transmission with frequencies up to 500 MHz (IEC 61076-3-124:2019)

This part of IEC 61076 covers 10-way, shielded, free and fixed rectangular connectors for data transmission with frequencies up to 500 MHz and specifies the common dimensions, mechanical, electrical and transmission characteristics and environmental requirements as well as test specifications respectively. Connectors covered in this document are provided in three codings that differ only for the position of the polarization key and keyway, in view of their differently intended use:
• Connectors Type A and C are intended for 10/100 Mbit/s as well as for 1/ 2,5 / 5 /10 Gbit/s Ethernet communication.
• Connectors Type B are intended for all other non-Ethernet applications such as signalling, serial or other industrial bus communication systems. A-coding: The 45° cut corner used as polarization key and keyway system is located on the lower left corner of the male fixed connector (viewed from mating face) (Figures 5a, 5b). B-coding: The 45° cut corner is located on the upper left corner of the male fixed connector (Figures 5c, 5d). C-coding: There are two 45° corners located at the upper left and lower left corner (Figures 5e, 5f). In this document, the three codings, A, B, and C are designated as “Type A”, “Type B” and “Type C”.

Steckverbinder für elektronische Einrichtungen - Produktanforderungen - Teil 3-124: Rechteckige Steckverbinder - Bauartspezifikation für 10-polige geschirmte freie und feste Steckverbinder für E/A und Datenübertragung mit Frequenzen bis zu 500 MHz (IEC 61076-3-124:2019)

Connecteurs pour équipements électriques et électroniques - Exigences de produit - Partie 3-124: Connecteurs rectangulaires - Spécification particulière pour les fiches et les embases écrantées à 10 voies pour les entrées/sorties et la transmission de données à des fréquences jusqu'à 500 MHz (IEC 61076-3-124:2019)

La présente partie de l'IEC 61076 couvre les fiches et les embases rectangulaires écrantées à 10 voies pour la transmission de données à des fréquences jusqu'à 500 MHz et elle spécifie les dimensions communes, les caractéristiques mécaniques, électriques et de transmission et les exigences environnementales ainsi que les spécifications d'essais.
Les connecteurs couverts par le présent document sont codés de trois manières différentes pour indiquer la position de la clé de polarisation et du système de détrompage, en fonction de l'utilisation prévue:
- Les connecteurs de Type A et C sont destinés à des applications de communication Ethernet jusqu'à 10/100 Mbit/s, mais aussi jusqu'à 1/2,5/5/10 Gbit/s.
- Les connecteurs de Type B sont destinés à toutes les autres applications "non Ethernet" telles que les systèmes de signalisation, les systèmes de communication sur des bus séries ou industriels.
Codage A: un bord coupé à 45°, servant de clé de polarisation et de système de détrompage, situé en bas à gauche de l'embase mâle (vue depuis la face d'accouplement), voir Figure 5a et Figure 5b.
Codage B: un bord coupé à 45°, situé en haut à gauche de l'embase mâle, voir Figure 5c et Figure 5d.
Codage C: deux bords coupés à 45°, situés en haut à gauche et en bas à gauche, voir Figure 5e et Figure 5f.
Dans le présent document, les trois codages A, B et C sont appelés "Type A", "Type B" et "Type C".

Konektorji za električno in elektronsko opremo - Zahteve za izdelek - 3-124. del: Pravokotni konektorji - Podrobna specifikacija za 10-redne, oklepljene, proste ali pritrjene konektorje za izvajanje vhodno/izhodnih funkcij (I/O) in prenosa podatkov s frekvencami do 500 MHz (IEC 61076-3-124:2019)

Ta del standarda IEC 61076 zajema 10-redne, oklepljene, proste ali pritrjene pravokotne konektorje za prenos podatkov s frekvencami do 500 MHz ter določa običajne mere, mehanske, električne in prenosne lastnosti ter okoljske zahteve in specifikacije preskusov.
Konektorji, zajeti v tem dokumentu, so podani v treh označitvah, ki se razlikujejo le po položaju polarizacijske zagozde in utora z vidika drugačne predvidene uporabe:
• Konektorji tipa A in C so namenjeni za 10/100 Mbit/s in 1/2,5/5/10 Gbit/s ethernetno komunikacijo.
• Konektorji tipa B so namenjeni za vse druge neethernetne uporabe, kot so komunikacijski sistemi signalnih, serijskih in drugih industrijskih vodil.
Označitev A: Vogal, ki je odrezan pod kotom 45° in se uporablja kot sistem polarizacijske zagozde in utora, se nahaja v spodnjem levem vogalu moškega pritrjenega konektorja (pogled s prednje strani stikanja) (sliki 5a, 5b).
Označitev B: Vogal, ki je odrezan pod kotom 45°, se nahaja v zgornjem levem vogalu moškega pritrjenega konektorja (sliki 5c, 5d).
Označitev C: Dva vogala, ki sta odrezana pod kotom 45°, se nahajata v zgornjem levem in spodnjem levem vogalu (sliki 5e, 5f).
V tem dokumentu so tri označitve A, B in C označene kot »tip A«, »tip B« in »tip C«.

General Information

Status
Published
Publication Date
22-May-2019
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
10-May-2019
Due Date
15-Jul-2019
Completion Date
23-May-2019

Relations

Buy Standard

Standard
EN IEC 61076-3-124:2019
English language
48 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61076-3-124:2019
01-julij-2019
Konektorji za električno in elektronsko opremo - Zahteve za izdelek - 3-124. del:
Pravokotni konektorji - Podrobna specifikacija za 10-redne, oklepljene, proste ali
pritrjene konektorje za izvajanje vhodno/izhodnih funkcij (I/O) in prenosa podatkov
s frekvencami do 500 MHz (IEC 61076-3-124:2019)
Connectors for electrical and electronic equipment - Product requirements - Part 3-124:
Rectangular connectors - Detail specification for 10-way, shielded, free and fixed
connectors for I/O and data transmission with frequencies up to 500 MHz (IEC 61076-3-
124:2019)
Steckverbinder für elektronische Einrichtungen - Produktanforderungen - Teil 3-124:
Rechteckige Steckverbinder - Bauartspezifikation für 10-polige geschirmte freie und
feste Steckverbinder für E/A und Datenübertragung mit Frequenzen bis zu 500 MHz
(IEC 61076-3-124:2019)
Connecteurs pour équipements électriques et électroniques - Exigences de produit -
Partie 3-124: Connecteurs rectangulaires - Spécification particulière pour les fiches et les
embases écrantées à 10 voies pour les entrées/sorties et la transmission de données à
des fréquences jusqu'à 500 MHz (IEC 61076-3-124:2019)
Ta slovenski standard je istoveten z: EN IEC 61076-3-124:2019
ICS:
31.220.10 Vtiči in vtičnice, konektorji Plug-and-socket devices.
Connectors
SIST EN IEC 61076-3-124:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN IEC 61076-3-124:2019

---------------------- Page: 2 ----------------------

SIST EN IEC 61076-3-124:2019


EUROPEAN STANDARD EN IEC 61076-3-124

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2019
ICS 31.220.10

English Version
Connectors for electrical and electronic equipment - Product
requirements - Part 3-124: Rectangular connectors - Detail
specification for 10-way, shielded, free and fixed connectors for
I/O and data transmission with frequencies up to 500 MHz
(IEC 61076-3-124:2019)
Connecteurs pour équipements électriques et électroniques Steckverbinder für elektronische Einrichtungen -
- Exigences de produit - Partie 3-124: Connecteurs Produktanforderungen - Teil 3-124: Rechteckige
rectangulaires - Spécification particulière pour les fiches et Steckverbinder - Bauartspezifikation für 10-polige
les embases écrantées à 10 voies pour les entrées/sorties geschirmte freie und feste Steckverbinder für E/A und
et la transmission de données à des fréquences jusqu'à Datenübertragung mit Frequenzen bis zu 500 MHz
500 MHz (IEC 61076-3-124:2019)
(IEC 61076-3-124:2019)
This European Standard was approved by CENELEC on 2019-04-15. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61076-3-124:2019 E

---------------------- Page: 3 ----------------------

SIST EN IEC 61076-3-124:2019
EN IEC 61076-3-124:2019 (E)
European foreword
The text of document 48B/2711/FDIS, future edition 1 of IEC 61076-3-124, prepared by SC 48B
"Electrical connectors" of IEC/TC 48 "Electrical connectors and mechanical structures for electrical
and electronic equipment" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 61076-3-124:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-01-15
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-04-15
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61076-3-124:2019 was approved by CENELEC as a
European Standard without any modification.


2

---------------------- Page: 4 ----------------------

SIST EN IEC 61076-3-124:2019
EN IEC 61076-3-124:2019 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050-581 -  International Electrotechnical Vocabulary (IEV) - -
- Chapter 581: Electromechanical components
for electronic equipment
IEC 60068-1 -  Environmental testing - Part 1: General and EN 60068-1 -
guidance
IEC 60068-2-38 -  Environmental testing - Part 2-38: Tests - Test EN 60068-2-38 -
Z/AD: Composite temperature/humidity cyclic
test
IEC 60352 series Solderless connections  EN 60352 series
IEC 60512-1 -  Connectors for electrical and electronic EN IEC 60512-1 -
equipment - Tests and measurements - Part 1:
Generic specification
IEC 60512-1-1 -  Connectors for electronic equipment - Tests EN 60512-1-1 -
and measurements - Part 1-1: General
examination - Test 1a: Visual examination
IEC 60512-1-2 -  Connectors for electronic equipment - Tests EN 60512-1-2 -
and measurements - Part 1-2: General
examination - Test 1b: Examination of
dimension and mass
IEC 60512-2-1 -  Connectors for electronic equipment - Tests EN 60512-2-1 -
and measurements - Part 2-1: Electrical
continuity and contact resistance tests - Test
2a: Contact resistance - Millivolt level method
IEC 60512-2-5 -  Connectors for electronic equipment - Tests EN 60512-2-5 -
and measurements - Part 2-5: Electrical
continuity and contact resistance tests - Test
2e: Contact disturbance
IEC 60512-3-1 -  Connectors for electronic equipment - Tests EN 60512-3-1 -
and measurements - Part 3-1: Insulation tests -
Test 3a: Insulation resistance
IEC 60512-4-1 -  Connectors for electronic equipment - Tests EN 60512-4-1 -
and measurements - Part 4-1: Voltage stress
tests - Test 4a: Voltage proof
IEC 60512-5-2 -  Connectors for electronic equipment - Tests EN 60512-5-2 -
and measurements - Part 5-2: Current-carrying
capacity tests - Test 5b: Current-temperature
derating
3

---------------------- Page: 5 ----------------------

SIST EN IEC 61076-3-124:2019
EN IEC 61076-3-124:2019 (E)
IEC 60512-6-3 -  Connectors for electronic equipment - Tests EN 60512-6-3 -
and measurements - Part 6-3: Dynamic stress
tests - Test 6c: Shock
IEC 60512-6-4 -  Connectors for electronic equipment - Tests EN 60512-6-4 -
and measurements - Part 6-4: Dynamic stress
tests - Test 6d: Vibration (sinusoidal)
IEC 60512-9-1 -  Connectors for electronic equipment - Tests EN 60512-9-1 -
and measurements - Part 9-1: Endurance tests
- Test 9a: Mechanical operation
IEC 60512-11-3 -  Connectors for electronic equipment - Tests EN 60512-11-3 -
and measurements - Part 11-3: Climatic tests -
Test 11c: Damp heat, steady state
IEC 60512-11-4 -  Connectors for electronic equipment - Tests EN 60512-11-4 -
and measurements - Part 11-4: Climatic tests -
Test 11d: Rapid change of temperature
IEC 60512-11-7 -  Connectors for electronic equipment - Tests EN 60512-11-7 -
and measurements - Part 11-7: Climatic tests -
Test 11g: Flowing mixed gas corrosion test
IEC 60512-11-9 -  Connectors for electronic equipment - Tests EN 60512-11-9 -
and measurements - Part 11-9: Climatic tests -
Test 11i: Dry heat
IEC 60512-11-10 -  Connectors for electronic equipment - Tests EN 60512-11-10 -
and measurements - Part 11-10: Climatic tests -
Test 11j: Cold
IEC 60512-13-2 -  Connectors for electronic equipment - Tests EN 60512-13-2 -
and measurements - Part 13-2: Mechanical
operation tests - Test 13b: Insertion and
withdrawal forces
IEC 60512-13-5 -  Connectors for electronic equipment - Tests EN 60512-13-5 -
and measurements - Part 13-5: Mechanical
operation tests - Test 13e: Polarizing and
keying method
IEC 60512-15-6 -  Connectors for electronic equipment - Tests EN 60512-15-6 -
and measurements - Part 15-6: Connector tests
(mechanical) - Test 15f: Effectiveness of
connector coupling devices
IEC 60512-25-7 -  Connectors for electronic equipment - Tests EN 60512-25-7 -
and measurements - Part 25-7: Test 25g -
Impedance, reflection coefficient, and voltage
standing wave ratio (VSWR)
IEC 60512-27-100 -  Connectors for electronic equipment - Tests EN 60512-27-100 -
and measurements - Part 27-100: Signal
integrity tests up to 500 MHz on 60603-7 series
connectors - Tests 27a to 27g
IEC 60603-7 2008 Connectors for electronic equipment - Part 7: EN 60603-7 2009
Detail specification for 8-way, unshielded, free
and fixed connectors
IEC 60664-1 -  Insulation coordination for equipment within EN 60664-1 -
low-voltage systems - Part 1: Principles,
requirements and tests
IEC 61076-1 2006 Connectors for electronic equipment - Product EN 61076-1 2006
requirements - Part 1: Generic specification
IEC 61076-3 2008 Connectors for electronic equipment - Product EN 61076-3 2008
requirements - Part 3: Rectangular connectors -
Sectional specification

4

---------------------- Page: 6 ----------------------

SIST EN IEC 61076-3-124:2019



IEC 61076-3-124

®


Edition 1.0 2019-03




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Connectors for electrical and electronic equipment – Product requirements –

Part 3-124: Rectangular connectors – Detail specification for 10-way, shielded,

free and fixed connectors for I/O and data transmission with frequencies up to


500 MHz



Connecteurs pour équipements électriques et électroniques – Exigences de


produit –

Partie 3-124: Connecteurs rectangulaires – Spécification particulière pour les

fiches et les embases écrantées à 10 voies pour les entrées/sorties et la

transmission de données à des fréquences jusqu'à 500 MHz









INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 31.220.10 ISBN 978-2-8322-6608-3




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN IEC 61076-3-124:2019
– 2 – IEC 61076-3-124:2019 © IEC 2019
CONTENTS
FOREWORD . 5
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 10
4 Technical information . 10
4.1 Systems of levels – Compatibility levels, according to IEC 61076-1:2006 . 10
4.1.1 Performance level . 10
4.1.2 Compatibility levels according to IEC 61076 . 10
4.2 Classification into climatic categories . 10
4.3 Clearance and creepage distances . 11
4.4 Current carrying capacity . 11
4.5 Marking . 11
5 Dimensional information . 11
5.1 General . 11
5.2 Isometric view and common features . 11
5.2.1 Common features . 11
5.2.2 Reference system . 11
5.3 Mating information – Contacts – mating conditions. 12
5.4 Fixed connector . 14
5.5 Free connector . 20
5.6 Accessories . 25
5.7 Mounting information for connectors . 25
5.8 Gauges . 25
6 Characteristics . 26
6.1 General . 26
6.2 Pin and pair grouping assignment . 26
6.3 Classification into climatic category . 28
6.4 Electrical characteristics . 28
6.4.1 Voltage rating . 28
6.4.2 Creepage and clearance distances . 28
6.4.3 Voltage proof . 29
6.4.4 Current-carrying capacity . 29
6.4.5 Contact and shield resistance . 30
6.4.6 Initial insulation resistance . 30
6.4.7 Impedance . 30
6.5 Mechanical characteristics . 31
6.5.1 Mechanical operation . 31
6.5.2 Insertion and withdrawal forces . 31
6.5.3 Polarization and coding method . 31
6.5.4 Effectivess of connector coupling devices . 31
6.6 Transmission performance . 32
6.6.1 General . 32
6.6.2 Insertion loss . 32
6.6.3 Return loss . 32
6.6.4 Near-end crosstalk . 32
6.6.5 Far-end crosstalk . 33

---------------------- Page: 8 ----------------------

SIST EN IEC 61076-3-124:2019
IEC 61076-3-124:2019 © IEC 2019 – 3 –
6.6.6 Transverse conversion loss . 33
6.6.7 Transverse conversion transfer loss . 33
6.6.8 Transfer impedance . 33
6.6.9 Propagation delay . 33
6.6.10 Delay skew . 33
7 Test schedule . 34
7.1 General . 34
7.2 Test procedures and measuring methods . 34
7.3 Mounting of specimens . 34
7.3.1 General . 34
7.3.2 Arrangement for contact resistance measurement . 34
7.3.3 Arrangement for dynamic stress tests . 35
7.3.4 Wiring of specimens . 36
7.4 Test schedules . 36
7.4.1 Basic (minimum) test schedule . 36
7.4.2 Full test schedule . 36

Figure 1 – View showing typical fixed and free connectors . 11
Figure 2 – Contact interface dimensions with terminated free connector . 12
Figure 3a – Fixed connector Type A. 14
Figure 3b – Fixed connector Type B. 16
Figure 3c – Fixed connector Type C. 18
Figure 3 – Fixed connectors . 18
Figure 4a – Free connector Type A . 20
Figure 4b – Free connector Type B . 22
Figure 4c – Free connector Type C . 24
Figure 4 – Free connectors . 24
Figure 5a – Fixed connector pin assignment for Type A, front view of connector . 26
Figure 5b – Free connector pin assignment for Type A, front view of connector . 26
Figure 5c – Fixed connector pin assignment for Type B, front view of connector . 26
Figure 5d – Free connector pin assignment for Type B, front view of connector . 27
Figure 5e – Fixed connector pin assignment for Type C, front view of connector . 27
Figure 5f – Free connector pin assignment for Type C, front view of connector . 27
Figure 5 – Connector pin assignment . 27
Figure 6 – Derating diagram . 30
Figure 7 – Contact resistance arrangement . 35
Figure 8 – Arrangement for vibration test . 36

Table 1 – Dimensions for Figure 2 . 12
Table 2 – Dimensions for Figure 3a . 15
Table 3 – Dimensions for Figure 3b . 17
Table 4 – Dimensions for Figure 3c . 19
Table 5 – Dimensions for Figure 4a . 21
Table 6 – Dimensions for Figure 4b . 23
Table 7 – Dimensions for Figure 4c . 25

---------------------- Page: 9 ----------------------

SIST EN IEC 61076-3-124:2019
– 4 – IEC 61076-3-124:2019 © IEC 2019
Table 8 – Board connector pin assignment for 10/100 Mbit/s Ethernet (Type A connectors
of Figure 5a and Figure 5b and Type C connectors of Figure 5e and Figure 5f) . 27
Table 9 – Board connector pin assignment for 1/10 Gbit/s Ethernet: (Type A connectors

of Figure 5a and Figure 5b and Type C connectors of Figure 5e and Figure 5f) . 28
Table 10 – Climatic category . 28
Table 11 – Creepage and clearance distances . 29
Table 12 – Preferred values for the number of mating cycles . 31
Table 13 – Test group P . 37
Table 14 – Test group AP . 38
Table 15 – Test group BP . 40
Table 16 – Test group CP . 41
Table 17 – Test group DP . 42
Table 18 – Test group EP . 43
Table 19 – Test group FP . 44

---------------------- Page: 10 ----------------------

SIST EN IEC 61076-3-124:2019
IEC 61076-3-124:2019 © IEC 2019 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT –
PRODUCT REQUIREMENTS –

Part 3-124: Rectangular connectors – Detail specification for 10-way,
shielded, free and fixed connectors for I/O and data transmission
with frequencies up to 500 MHz

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
This International Standard IEC 61076-3-124 has been prepared by subcommittee 48B:
Electrical connectors, of IEC technical committee 48: Electrical connectors and mechanical
structures for electrical and electronic equipment.
The text of this International Standard is based on the following documents:
FDIS Report on voting
48B/2711/FDIS 48B/2726/RVD

Full information on the voting for the approval of this International Standard can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 11 ----------------------

SIST EN IEC 61076-3-124:2019
– 6 – IEC 61076-3-124:2019 © IEC 2019
A list of all parts in the IEC 61076 series, published under the general title Connectors for
electrical and electronic equipment – Product requirements, can be found on the IEC website.
Future standards in this series will carry the new general title as cited above. Titles of existing
standards in this series will be updated at the time of the next edition.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.ie
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.