SIST EN IEC 60335-2-111:2020

Household and similar electrical appliances - Safety - Part 2-111: Particular requirements for electric ondol mattress with a non-flexible heated part

This standard deals with the safety of electric ondol-mattresses for household and similar purposes, their rated voltage being not more than 250 V. This standard also applies to control units supplied with the appliance. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used in community spas or by persons in cold ambient temperatures, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account - the use of appliances by young children or infirm persons without supervision; - playing with the appliance by young children.

Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-111: Besondere Anforderungen für elektrische Ondol-Matratzen mit einem nicht flexiblen beheizten Teil

Appareils électrodomestiques et analogues - Sécurité - Part 2-111: Exigences particulières pour les matelas électriques ondol avec une partie chauffée non-flexible

L'IEC 60335-2-111:2015 traite de la sécurité des matelas ondol électriques pour usages domestiques et analogues, dont la tension assignée n'est pas supérieure à 250 V. La présente norme s'applique également aux unités de commande alimentées par l'appareil. Les appareils non destinés à un usage domestique normal mais qui néanmoins peuvent constituer une source de danger pour le public, tels que les appareils destinés à être utilisés dans les stations thermales ou par des personnes séjournant à des températures ambiantes froides, relèvent du domaine d'application de la présente norme. Dans la mesure du possible, la présente norme traite des dangers ordinaires présentés par les appareils, encourus par tous les individus à l'intérieur et autour de l'habitation. Cependant, cette norme ne tient pas compte en général de l'utilisation des appareils par des jeunes enfants ou des personnes handicapées sans surveillance ou de l'emploi de l'appareil comme jouet par des jeunes enfants. Elle a été établie sur la base de la cinquième édition (2010) de cette norme. L'attention des Comités nationaux est attirée sur le fait que les fabricants d'appareils et les organismes d'essai peuvent avoir besoin d'une période transitoire après la publication d'une nouvelle publication IEC, ou d'une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés. Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 12 mois ou au plus tard 36 mois après la date de publication.
Mots-clés: matelas ondol, élément chauffant, partie chauffée non flexible
Cette publication doit être lue conjointement avec la CEI 60335-1:2013.

Gospodinjski in podobni električni aparati - Varnost - 2-111. del: Posebne zahteve za grelne vzmetnice s togimi grelnimi elementi

Ta standard obravnava varnost grelnih vzmetnic za gospodinjsko ali podobno uporabo, pri čemer njihova nazivna napetost ni višja od 250 V. Ta standard se uporablja tudi za krmilne enote, ki so priložene aparatu. Področje uporabe tega standarda zajema aparate, ki niso namenjeni za običajno gospodinjsko uporabo, vendar so lahko vir nevarnosti za javnost, kot so aparati, namenjeni za uporabo v zdraviliščih ali s strani oseb pri nizkih okoljskih temperaturah. Ta standard v največji možni meri obravnava splošne nevarnosti, ki jih predstavljajo aparati ter s katerimi se srečujejo osebe doma in v okolici doma. Vendar na splošno ne upošteva: – uporabe aparatov s strani majhnih otrok ali onemoglih oseb brez nadzora; – uporabe aparata pri igri.

General Information

• Status: Published
• Publication Date: 10-Dec-2019
• ICS: 97.030 - Domestic electrical appliances in general
• Technical Committee: VGA - Safety of household and similar electrical appliances
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 05-Dec-2019
• Due Date: 09-Feb-2020
• Completion Date: 11-Dec-2019
• Ref Project: EN IEC 60335-2-111:2019 - Household and similar electrical appliances - Safety - Part 2-111: Particular requirements for electric ondol mattress with a non-flexible heated part

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 60335-2-111:2020
01-januar-2020
Gospodinjski in podobni električni aparati - Varnost - 2-111. del: Posebne zahteve
za grelne vzmetnice s togimi grelnimi elementi
Household and similar electrical appliances - Safety - Part 2-111: Particular requirements
for electric ondol mattress with a non-flexible heated part
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-111:
Besondere Anforderungen für elektrische Ondol-Matratzen mit einem nicht flexiblen
beheizten Teil
Appareils électrodomestiques et analogues - Sécurité - Part 2-111: Exigences
particulières pour les matelas électriques ondol avec une partie chauffée non-flexible
Ta slovenski standard je istoveten z: EN IEC 60335-2-111:2019
ICS:
97.030 Električni aparati za dom na Domestic electrical
splošno appliances in general
SIST EN IEC 60335-2-111:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60335-2-111:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 60335-2-111:2020


EUROPEAN STANDARD EN IEC 60335-2-111

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2019
ICS 97.030

English Version
Household and similar electrical appliances - Safety - Part 2-111:
Particular requirements for electric ondol mattress with a non-
flexible heated part
(IEC 60335-2-111:2015)
Appareils électrodomestiques et analogues - Sécurité - Part Sicherheit elektrischer Geräte für den Hausgebrauch und
2-111: Exigences particulières pour les matelas électriques ähnliche Zwecke - Teil 2-111: Besondere Anforderungen für
ondol avec une partie chauffée non-flexible elektrische Ondol-Matratzen mit einem nicht flexiblen
(IEC 60335-2-111:2015) beheizten Teil
(IEC 60335-2-111:2015)
This European Standard was approved by CENELEC on 2019-04-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60335-2-111:2019 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60335-2-111:2020
EN IEC 60335-2-111:2019 (E)
European foreword
The text of document 61/4826FDIS, future edition 1 of IEC 60335-2-111:2015, prepared by IEC/TC 61
"Safety of household and similar electrical appliances" was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN IEC 60335-2-111:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-05-08
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-11-08
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This standard shall be read in conjunction with IEC 60335-1:2010+A1:2013+A2:2016+COR1:2016
This standards is not linked to any European legislation.
Endorsement notice
The text of the International Standard IEC 60335-2-111:2015 was approved by CENELEC as a
European Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60335-2-17 NOTE Harmonized as EN 60335-2-17
IEC 60335-2-30 NOTE Harmonized as EN 60335-2-30
IEC 60335-2-66 NOTE Harmonized as EN 60335-2-66
IEC 60335-2-71 NOTE Harmonized as EN 60335-2-71
IEC 60335-2-81 NOTE Harmonized as EN 60335-2-81
IEC 60335-2-96 NOTE Harmonized as EN 60335-2-96
IEC 60335-2-106 NOTE Harmonized as EN 60335-2-106
IEC 80601-2-35 NOTE Harmonized as EN 80601-2-35

2

---------------------- Page: 4 ----------------------
SIST EN IEC 60335-2-111:2020
EN IEC 60335-2-111:2019 (E)
Annex ZC
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
The Annex ZC of Part 1 apples, except as follows:
Publication Year Title EN/HD Year
Addition
ISO 2439 -  Flexible cellular polymeric materials - EN ISO 2439 -
Determination of hardness (indentation
technique)

3

---------------------- Page: 5 ----------------------
SIST EN IEC 60335-2-111:2020

---------------------- Page: 6 ----------------------
SIST EN IEC 60335-2-111:2020



IEC 60335-2-111

®


Edition 1.0 2015-01




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Household and similar electrical appliances – Safety –

Part 2-111: Particular requirements for electric ondol mattress with a non-

flexible heated part




Appareils électrodomestiques et analogues – Sécurité –

Partie 2-111: Exigences particulières pour les matelas électriques ondol


avec une partie chauffée non flexible













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 13.120; 97.100.10; 97.140 ISBN 978-2-8322-2186-0



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 60335-2-111:2020
– 2 – IEC 60335-2-111:2015 © IEC 2015
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 General requirement . 7
5 General conditions for the tests . 7
6 Classification . 8
7 Marking and instructions . 8
8 Protection against access to live parts . 9
9 Starting of motor-operated appliances . 9
10 Power input and current . 9
11 Heating . 9
12 Void . 10
13 Leakage current and electric strength at operating temperature . 10
14 Transient overvoltages . 10
15 Moisture resistance . 10
16 Leakage current and electric strength . 10
17 Overload protection of transformers and associated circuits . 11
18 Endurance . 11
19 Abnormal operation . 11
20 Stability and mechanical hazards . 12
21 Mechanical strength . 12
22 Construction . 12
23 Internal wiring . 13
24 Components . 13
25 Supply connection and external flexible cords . 13
26 Terminals for external conductors . 13
27 Provision for earthing . 14
28 Screws and connections . 14
29 Clearances, creepage distances and solid insulation . 14
30 Resistance to heat and fire . 14
31 Resistance to rusting . 14
32 Radiation, toxicity and similar hazards . 14
Bibliography . 17

Figure 101 – Arrangement for measuring leakage current and electric strength of the
ondol-mattress . 15
Figure 102 – Positioning of the thermal insulation on an ondol-mattress incorporating
thermostats . 15

---------------------- Page: 8 ----------------------
SIST EN IEC 60335-2-111:2020
IEC 60335-2-111:2015 © IEC 2015 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –

Part 2-111: Particular requirements for electric ondol
mattress with a non-flexible heated part

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60335-2-111 has been prepared by IEC technical committee 61:
Safety of household and similar electrical appliances.
It forms the first edition of IEC 60335-2-111.
The text of this standard is based on the following documents:
FDIS Report on voting
61/4826/FDIS 61/4873/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 9 ----------------------
SIST EN IEC 60335-2-111:2020
– 4 – IEC 60335-2-111:2015 © IEC 2015
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its
amendments. It was established on the basis of the fifth edition (2010) of that standard.
NOTE 1 When “Part 1” is mentioned in this standard, it refers to IEC 60335-1.
This part 2 supplements or modifies the corresponding clauses in IEC 60335-1, so as to
convert that publication into the IEC standard: Safety requirements for electric ondol mattress
with a non-flexible heated part.
When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies
as far as is reasonable. When this standard states "addition", "modification" or "replacement",
the relevant text in Part 1 is to be adapted accordingly.
NOTE 2 The following numbering system is used:
– subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1;
– unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including
those in a replaced clause or subclause;
– additional annexes are lettered AA, BB, etc.
NOTE 3 The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the
associated noun are also in bold.
NOTE 4 The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of this standard be adopted for implementation
nationally not earlier than 12 months or later than 36 months from the date of its publication.
A list of all parts of the IEC 60335 series, under the general title: Household and similar
electrical appliances – Safety, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 10 ----------------------
SIST EN IEC 60335-2-111:2020
IEC 60335-2-111:2015 © IEC 2015 – 5 –
INTRODUCTION
It has been assumed in the drafting of this International Standard that the execution of its
provisions is entrusted to appropriately qualified and experienced persons.
This standard recognizes the internationally accepted level of protection against hazards such
as electrical, mechanical, thermal, fire and radiation of appliances when operated as in
normal use taking into account the manufacturer's instructions. It also covers abnormal
situations that can be expected in practice and takes into account the way in which
electromagnetic phenomena can affect the safe operation of appliances.
This standard takes into account the requirements of IEC 60364 as far as possible so that
there is compatibility with the wiring rules when the appliance is connected to the supply
mains. However, national wiring rules may differ.
If an appliance within the scope of this standard also incorporates functions that are covered
by another part 2 of IEC 60335, the relevant part 2 is applied to each function separately, as
far as is reasonable. If applicable, the influence of one function on the other is taken into
account.
When a part 2 standard does not include additional requirements to cover hazards dealt with
in Part 1, Part 1 applies.
NOTE 1 This means that the technical committees responsible for the part 2 standards have determined that it is
not necessary to specify particular requirements for the appliance in question over and above the general
requirements.
Thi
...