SIST EN ISO 12402-8:2006/A1:2011
(Amendment)Personal flotation devices - Part 8: Accessories - Safety requirements and test methods - Amendment 1 (ISO 12402-8:2006/Amd 1:2011)
Personal flotation devices - Part 8: Accessories - Safety requirements and test methods - Amendment 1 (ISO 12402-8:2006/Amd 1:2011)
This part of prEN ISO 12402 specifies the safety requirements and test methods for accessories used for personal flotation devices ( hereafter referred to as PFD).
Persönliche Auftriebsmittel - Zubehörteile - Teil 8: Sicherheitstechnische Anforderungen und Prüfverfahren - Änderung 1 (ISO 12402-8:2006/Amd 1:2011)
Équipements individuels de flottabilité - Partie 8: Accessoires - Exigences de securité et méthodes d'essai - Amendement 1 (ISO 12402-8:2006/Amd 1:2011)
Osebni plavajoči pripomočki - 8. del: Dodatki - Varnostne zahteve in preskusne metode - Dopolnilo 1 (ISO 12402-8:2006/Amd 1:2011)
Ta del prEN ISO 12402 določa varnostne zahteve in preskusne metode za dodatke, ki se uporabljajo pri osebnih plavajočih pripomočkih (v nadaljevanju PFD).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 12402-8:2006/A1:2011
01-julij-2011
2VHEQLSODYDMRþLSULSRPRþNLGHO 'RGDWNL9DUQRVWQH]DKWHYHLQSUHVNXVQH
PHWRGH'RSROQLOR ,62 $PG
Personal flotation devices - Part 8: Accessories - Safety requirements and test methods -
Amendment 1 (ISO 12402-8:2006/Amd 1:2011)
Persönliche Auftriebsmittel - Zubehörteile - Teil 8: Sicherheitstechnische Anforderungen
und Prüfverfahren - Änderung 1 (ISO 12402-8:2006/Amd 1:2011)
Équipements individuels de flottabilité - Partie 8: Accessoires - Exigences de securité et
méthodes d'essai - Amendement 1 (ISO 12402-8:2006/Amd 1:2011)
Ta slovenski standard je istoveten z: EN ISO 12402-8:2006/A1:2011
ICS:
13.340.70 5HãLOQLMRSLþLY]JRQVND Lifejackets, buoyancy aids
SRPDJDODLQSODYDMRþL and floating devices
SULSRPRþNL
SIST EN ISO 12402-8:2006/A1:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 12402-8:2006/A1:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 12402-8:2006/A1:2011
EUROPEAN STANDARD
EN ISO 12402-8:2006/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 13.340.70
English Version
Personal flotation devices - Part 8: Accessories - Safety
requirements and test methods - Amendment 1 (ISO 12402-
8:2006/Amd 1:2011)
Équipements individuels de flottabilité - Partie 8: Persönliche Auftriebsmittel - Zubehörteile - Teil 8:
Accessoires - Exigences de securité et méthodes d'essai - Sicherheitstechnische Anforderungen und Prüfverfahren
Amendement 1 (ISO 12402-8:2006/Amd 1:2011) (ISO 12402-8:2006/Amd 1:2011)
This amendment A1 modifies the European Standard EN ISO 12402-8:2006; it was approved by CEN on 29 January 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12402-8:2006/A1:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 12402-8:2006/A1:2011
EN ISO 12402-8:2006/A1:2011 (E)
Contents Page
Foreword .3
Annex ZA (informative) Relationship between this International Standard and the Essential
Requirements of EU Directive 89/686/EEC .4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 12402-8:2006/A1:2011
EN ISO 12402-8:2006/A1:2011 (E)
Foreword
This document (EN ISO 12402-8:2006/A1:2011) has been prepared by Technical Committee ISO/TC 188
"Small craft" in collaboration with Technical Committee CEN/TC 162 “Protective clothing including hand and
arm protection and lifejackets” the secretariat of which is held by DIN.
This Amendment to the European Standard EN ISO 12402-8:2006 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and
conflicting national standards shall be withdrawn at the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 12402-8:2006/Amd 1:2011 has been approved by CEN as a EN ISO 12402-8:2006/A1:2011
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 12402-8:2006/A1:2011
EN ISO 12402-8:2006/A1:2011 (E)
Annex ZA
(informative)
Relationship between this International Standard and the Essential
Requirements of EU Directive 89/686/EEC
This International Standard has been prepared under a mandate given to CEN by the European Commission
to provide one means of conforming to Essential Requirements of the New Approach Directive 89/686/EEC on
the approximation of the laws of the Member States relating to personal protective equipment.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this standard confers, within the limits of the scope of this standard, a presumption of conformity with the
corresponding Essential Requirements of that Directive and associated EFTA regulations.
WARNING: Other requirements and other EU Directives may be applicable to the products falling within the
scope of this standard.
4
---------------------- Page: 6 ----------------------
SIST EN ISO 12402-8:2006/A1:2011
INTERNATIONAL ISO
STANDARD 12402-8
First edition
2006-02-01
AMENDMENT 1
2011-04-01
Personal flotation devices —
Part 8:
Accessories — Safety requirements and
test methods
AMENDMENT 1
Équipements individuels de flottabilité —
Partie 8: Accessoires — Exigences de sécurité et méthodes d'essai
AMENDEMENT 1
Reference number
ISO 12402-8:2006/Amd.1:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 12402-8:2006/A1:2011
ISO 12402-8:2006/Amd.1:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 12402-8:2006/A1:2011
ISO 12402-8:2006/Amd.1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 12402-8:2006 was prepared by Technical Committe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.