SIST EN 303 213-5-1 V1.1.1:2020
(Main)Advanced Surface Movement Guidance and Control System (A-SMGCS) - Part 5: Harmonised Standard for access to radio spectrum for Multilateration (MLAT) equipment - Sub-part 1: Receivers and Interrogators
Advanced Surface Movement Guidance and Control System (A-SMGCS) - Part 5: Harmonised Standard for access to radio spectrum for Multilateration (MLAT) equipment - Sub-part 1: Receivers and Interrogators
The present document specifies technical characteristics and methods of measurements for the following equipment:
1) Interrogators transmitting in the 1 030 MHz band, used in Mode S multilateration equipment in an Advanced
Surface Movement Guidance and Control System (A-SMGCS).
2) Receivers, receiving in the 1 090 MHz band, used in Mode S multilateration equipment in an Advanced
Surface Movement Guidance and Control System (A-SMGCS).
Antennas for this equipment are external and passive without an additional amplifier.
The present document does not apply to equipment which includes a transponder function, to ground vehicle locators
and to reference transmitters which do not contain receivers for the purpose of replying to interrogation.
NOTE: The relationship between the present document and essential requirements of article 3.2 of
Directive 2014/53/EU [i.1] is given in Annex A.
Napredni sistem za vodenje in nadzor gibanja po zemlji (A-SMGCS) - 5. del: Harmonizirani standard za dostop do radijskega spektra za večplastno (MLAT) opremo - 1. poddel: Sprejemniki in bralniki
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 303 213-5-1 V1.1.1:2020
01-junij-2020
Napredni sistem za vodenje in nadzor gibanja po zemlji (A-SMGCS) - 5. del:
Harmonizirani standard za dostop do radijskega spektra za večplastno (MLAT)
opremo - 1. poddel: Sprejemniki in bralniki
Advanced Surface Movement Guidance and Control System (A-SMGCS) - Part 5:
Harmonised Standard for access to radio spectrum for Multilateration (MLAT) equipment
- Sub-part 1: Receivers and Interrogators
Ta slovenski standard je istoveten z: ETSI EN 303 213-5-1 V1.1.1 (2020-03)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
SIST EN 303 213-5-1 V1.1.1:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
---------------------- Page: 2 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
ETSI EN 303 213-5-1 V1.1.1 (2020-03)
HARMONISED EUROPEAN STANDARD
Advanced Surface Movement Guidance and
Control System (A-SMGCS);
Part 5: Harmonised Standard for access to
radio spectrum for Multilateration (MLAT) equipment;
Sub-part 1: Receivers and Interrogators
---------------------- Page: 3 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
2 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
Reference
DEN/ERM-TGAERO-37-5-1
Keywords
aeronautical, harmonised standard,
interoperability, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
3 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.1 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance Requirements . 11
4.2.1 Applicability . 11
4.2.1.1 Equipment with multiple functions . 11
4.2.2 Transmitter operating frequency and frequency error . 11
4.2.2.1 Definition . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.2.3 Spectrum mask . 11
4.2.3.1 Definition . 11
4.2.3.2 Limits . 11
4.2.3.3 Conformance . 12
4.2.4 Residual Power Output . 12
4.2.4.1 Definition . 12
4.2.4.2 Limits . 12
4.2.4.3 Conformance . 12
4.2.5 Spurious emissions of transmitter in active mode . 12
4.2.5.1 Definition . 12
4.2.5.2 Limits . 13
4.2.5.3 Conformance . 13
4.2.6 Sensitivity variation over the operating frequency range. 13
4.2.6.1 Definition . 13
4.2.6.2 Limits . 13
4.2.6.3 Conformance . 13
4.2.7 RF selectivity and spurious response rejection . 13
4.2.7.1 Definition . 13
4.2.7.2 Limits . 13
4.2.7.3 Conformance . 14
4.2.8 Inter-modulation response rejection . 14
4.2.8.1 Definition . 14
4.2.8.2 Limits . 14
4.2.8.3 Conformance . 14
4.2.9 Co-channel rejection . 14
4.2.9.1 Definition . 14
4.2.9.2 Limits . 14
4.2.9.3 Conformance . 14
4.2.10 Blocking . 14
4.2.10.1 Definition . 14
4.2.10.2 Limits . 14
4.2.10.3 Conformance . 15
4.2.11 Sensitivity . 15
ETSI
---------------------- Page: 5 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
4 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
4.2.11.1 Definition . 15
4.2.11.2 Limits . 15
4.2.11.3 Conformance . 15
4.2.12 Receiver spurious emissions . 15
4.2.12.1 Definition . 15
4.2.12.2 Limits . 15
4.2.12.3 Conformance . 15
5 Testing for compliance with technical requirements . 15
5.1 Environmental conditions for testing . 15
5.1.1 General requirements . 15
5.1.2 Procedure for Tests . 16
5.1.2.1 All Equipment . 16
5.1.2.2 Equipment including Transmitters . 16
5.2 Interpretation of the measurement results . 16
5.3 Test and General Conditions . 16
5.3.1 Transmitter test signals . 16
5.3.1.1 General Considerations . 16
5.3.1.2 Test signal 1 . 16
5.3.1.3 Test signal 2 . 17
5.3.2 Simulated received signals . 17
5.3.2.1 General Considerations . 17
5.3.2.2 Test signal 3 . 17
5.3.2.3 Test signal 4 . 18
5.4 Transmitter tests . 18
5.4.1 Operating frequency and frequency error . 18
5.4.1.1 Description . 18
5.4.1.2 Test conditions . 18
5.4.1.3 Method of measurement . 18
5.4.1.4 Measurement procedure . 18
5.4.2 Spectrum mask . 19
5.4.2.1 Description . 19
5.4.2.2 Test conditions . 19
5.4.2.3 Method of measurement . 19
5.4.2.4 Measurement procedure . 19
5.4.3 Residual Power Output . 20
5.4.3.1 Description . 20
5.4.3.2 Test conditions . 20
5.4.3.3 Method of measurement . 20
5.4.3.4 Measurement procedure . 20
5.4.4 Spurious emissions of transmitter in active mode . 21
5.4.4.1 Description . 21
5.4.4.2 Test conditions . 21
5.4.4.3 Method of measurement . 21
5.4.4.4 Measurement Procedure . 21
5.5 Receiver Tests . 22
5.5.1 Sensitivity variation over the operating frequency range. 22
5.5.1.1 Description . 22
5.5.1.2 Test conditions . 22
5.5.1.3 Method of measurement . 22
5.5.1.4 Measurement procedure . 22
5.5.2 RF selectivity and spurious response rejection . 23
5.5.2.1 Description . 23
5.5.2.2 Test conditions . 23
5.5.2.3 Method of measurement . 23
5.5.2.4 Measurement procedure . 23
5.5.3 Inter-modulation response rejection . 23
5.5.3.1 Description . 23
5.5.3.2 Test conditions . 24
5.5.3.3 Method of measurement . 24
5.5.3.4 Measurement procedure . 24
5.5.4 Co-channel rejection . 25
ETSI
---------------------- Page: 6 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
5 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
5.5.4.1 Description . 25
5.5.4.2 Test conditions . 25
5.5.4.3 Method of measurement . 25
5.5.4.4 Measurement procedure . 25
5.5.5 Blocking . 26
5.5.5.1 Description . 26
5.5.5.2 Test conditions . 26
5.5.5.3 Method of measurement . 26
5.5.5.4 Measurement procedure . 26
5.5.6 Receiver spurious emissions . 27
5.5.6.1 Description . 27
5.5.6.2 Test conditions . 27
5.5.6.3 Method of measurement . 27
5.5.6.4 Measurement Procedure . 27
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 28
Annex B (informative): Bibliography . 30
Annex C (informative): Change history . 31
History . 32
ETSI
---------------------- Page: 7 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
6 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C (2015) 5376 final [i.3] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in Table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 5, sub-part 1, of a multi-part deliverable covering Advanced Surface Movement Guidance
and Control System (A-SMGCS), as identified below.
Part 1: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS surveillance service including external interfaces";
Part 2: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS airport safety support service";
Part 3: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for a deployed cooperative sensor including its interfaces";
Part 4: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for a deployed non-cooperative sensor including its interfaces";
Part 5: "Harmonised Standard for access to radio spectrum for multilateration equipment":
Sub-part 1: "Receivers and Interrogators";
Sub-part 2: "Reference and vehicle transmitters";
Part 6: "Harmonised Standard for access to radio spectrum for deployed surface movement radar sensors";
Part 7: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS routing service";
ETSI
---------------------- Page: 8 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
7 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
Part 8: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS guidance service".
National transposition dates
Date of adoption of this EN: 9 March 2020
Date of latest announcement of this EN (doa): 30 June 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2020
Date of withdrawal of any conflicting National Standard (dow): 31 December 2021
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression
...
SLOVENSKI STANDARD
SIST EN 303 213-5-1 V1.1.1:2020
01-junij-2020
Napredni sistem za vodenje in nadzor gibanja po zemlji (A-SMGCS) - 5. del:
Harmonizirani standard za dostop do radijskega spektra za večplastno (MLAT)
opremo - 1. poddel: Sprejemniki in bralniki
Advanced Surface Movement Guidance and Control System (A-SMGCS) - Part 5:
Harmonised Standard for access to radio spectrum for Multilateration (MLAT) equipment
- Sub-part 1: Receivers and Interrogators
Ta slovenski standard je istoveten z: ETSI EN 303 213-5-1 V1.1.1 (2020-03)
ICS:
03.220.50 Zračni transport Air transport
49.090 Oprema in instrumenti v On-board equipment and
zračnih in vesoljskih plovilih instruments
SIST EN 303 213-5-1 V1.1.1:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
---------------------- Page: 2 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
ETSI EN 303 213-5-1 V1.1.1 (2020-03)
HARMONISED EUROPEAN STANDARD
Advanced Surface Movement Guidance and
Control System (A-SMGCS);
Part 5: Harmonised Standard for access to
radio spectrum for Multilateration (MLAT) equipment;
Sub-part 1: Receivers and Interrogators
---------------------- Page: 3 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
2 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
Reference
DEN/ERM-TGAERO-37-5-1
Keywords
aeronautical, harmonised standard,
interoperability, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
3 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.1 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance Requirements . 11
4.2.1 Applicability . 11
4.2.1.1 Equipment with multiple functions . 11
4.2.2 Transmitter operating frequency and frequency error . 11
4.2.2.1 Definition . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.2.3 Spectrum mask . 11
4.2.3.1 Definition . 11
4.2.3.2 Limits . 11
4.2.3.3 Conformance . 12
4.2.4 Residual Power Output . 12
4.2.4.1 Definition . 12
4.2.4.2 Limits . 12
4.2.4.3 Conformance . 12
4.2.5 Spurious emissions of transmitter in active mode . 12
4.2.5.1 Definition . 12
4.2.5.2 Limits . 13
4.2.5.3 Conformance . 13
4.2.6 Sensitivity variation over the operating frequency range. 13
4.2.6.1 Definition . 13
4.2.6.2 Limits . 13
4.2.6.3 Conformance . 13
4.2.7 RF selectivity and spurious response rejection . 13
4.2.7.1 Definition . 13
4.2.7.2 Limits . 13
4.2.7.3 Conformance . 14
4.2.8 Inter-modulation response rejection . 14
4.2.8.1 Definition . 14
4.2.8.2 Limits . 14
4.2.8.3 Conformance . 14
4.2.9 Co-channel rejection . 14
4.2.9.1 Definition . 14
4.2.9.2 Limits . 14
4.2.9.3 Conformance . 14
4.2.10 Blocking . 14
4.2.10.1 Definition . 14
4.2.10.2 Limits . 14
4.2.10.3 Conformance . 15
4.2.11 Sensitivity . 15
ETSI
---------------------- Page: 5 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
4 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
4.2.11.1 Definition . 15
4.2.11.2 Limits . 15
4.2.11.3 Conformance . 15
4.2.12 Receiver spurious emissions . 15
4.2.12.1 Definition . 15
4.2.12.2 Limits . 15
4.2.12.3 Conformance . 15
5 Testing for compliance with technical requirements . 15
5.1 Environmental conditions for testing . 15
5.1.1 General requirements . 15
5.1.2 Procedure for Tests . 16
5.1.2.1 All Equipment . 16
5.1.2.2 Equipment including Transmitters . 16
5.2 Interpretation of the measurement results . 16
5.3 Test and General Conditions . 16
5.3.1 Transmitter test signals . 16
5.3.1.1 General Considerations . 16
5.3.1.2 Test signal 1 . 16
5.3.1.3 Test signal 2 . 17
5.3.2 Simulated received signals . 17
5.3.2.1 General Considerations . 17
5.3.2.2 Test signal 3 . 17
5.3.2.3 Test signal 4 . 18
5.4 Transmitter tests . 18
5.4.1 Operating frequency and frequency error . 18
5.4.1.1 Description . 18
5.4.1.2 Test conditions . 18
5.4.1.3 Method of measurement . 18
5.4.1.4 Measurement procedure . 18
5.4.2 Spectrum mask . 19
5.4.2.1 Description . 19
5.4.2.2 Test conditions . 19
5.4.2.3 Method of measurement . 19
5.4.2.4 Measurement procedure . 19
5.4.3 Residual Power Output . 20
5.4.3.1 Description . 20
5.4.3.2 Test conditions . 20
5.4.3.3 Method of measurement . 20
5.4.3.4 Measurement procedure . 20
5.4.4 Spurious emissions of transmitter in active mode . 21
5.4.4.1 Description . 21
5.4.4.2 Test conditions . 21
5.4.4.3 Method of measurement . 21
5.4.4.4 Measurement Procedure . 21
5.5 Receiver Tests . 22
5.5.1 Sensitivity variation over the operating frequency range. 22
5.5.1.1 Description . 22
5.5.1.2 Test conditions . 22
5.5.1.3 Method of measurement . 22
5.5.1.4 Measurement procedure . 22
5.5.2 RF selectivity and spurious response rejection . 23
5.5.2.1 Description . 23
5.5.2.2 Test conditions . 23
5.5.2.3 Method of measurement . 23
5.5.2.4 Measurement procedure . 23
5.5.3 Inter-modulation response rejection . 23
5.5.3.1 Description . 23
5.5.3.2 Test conditions . 24
5.5.3.3 Method of measurement . 24
5.5.3.4 Measurement procedure . 24
5.5.4 Co-channel rejection . 25
ETSI
---------------------- Page: 6 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
5 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
5.5.4.1 Description . 25
5.5.4.2 Test conditions . 25
5.5.4.3 Method of measurement . 25
5.5.4.4 Measurement procedure . 25
5.5.5 Blocking . 26
5.5.5.1 Description . 26
5.5.5.2 Test conditions . 26
5.5.5.3 Method of measurement . 26
5.5.5.4 Measurement procedure . 26
5.5.6 Receiver spurious emissions . 27
5.5.6.1 Description . 27
5.5.6.2 Test conditions . 27
5.5.6.3 Method of measurement . 27
5.5.6.4 Measurement Procedure . 27
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 28
Annex B (informative): Bibliography . 30
Annex C (informative): Change history . 31
History . 32
ETSI
---------------------- Page: 7 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
6 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C (2015) 5376 final [i.3] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in Table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 5, sub-part 1, of a multi-part deliverable covering Advanced Surface Movement Guidance
and Control System (A-SMGCS), as identified below.
Part 1: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS surveillance service including external interfaces";
Part 2: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS airport safety support service";
Part 3: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for a deployed cooperative sensor including its interfaces";
Part 4: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for a deployed non-cooperative sensor including its interfaces";
Part 5: "Harmonised Standard for access to radio spectrum for multilateration equipment":
Sub-part 1: "Receivers and Interrogators";
Sub-part 2: "Reference and vehicle transmitters";
Part 6: "Harmonised Standard for access to radio spectrum for deployed surface movement radar sensors";
Part 7: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS routing service";
ETSI
---------------------- Page: 8 ----------------------
SIST EN 303 213-5-1 V1.1.1:2020
7 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
Part 8: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS guidance service".
National transposition dates
Date of adoption of this EN: 9 March 2020
Date of latest announcement of this EN (doa): 30 June 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2020
Date of withdrawal of any conflicting National Standard (dow): 31 December 2021
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause
...
ETSI EN 303 213-5-1 V1.1.1 (2020-03)
HARMONISED EUROPEAN STANDARD
Advanced Surface Movement Guidance and
Control System (A-SMGCS);
Part 5: Harmonised Standard for access to
radio spectrum for Multilateration (MLAT) equipment;
Sub-part 1: Receivers and Interrogators
---------------------- Page: 1 ----------------------
2 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
Reference
DEN/ERM-TGAERO-37-5-1
Keywords
aeronautical, harmonised standard,
interoperability, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.1 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance Requirements . 11
4.2.1 Applicability . 11
4.2.1.1 Equipment with multiple functions . 11
4.2.2 Transmitter operating frequency and frequency error . 11
4.2.2.1 Definition . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.2.3 Spectrum mask . 11
4.2.3.1 Definition . 11
4.2.3.2 Limits . 11
4.2.3.3 Conformance . 12
4.2.4 Residual Power Output . 12
4.2.4.1 Definition . 12
4.2.4.2 Limits . 12
4.2.4.3 Conformance . 12
4.2.5 Spurious emissions of transmitter in active mode . 12
4.2.5.1 Definition . 12
4.2.5.2 Limits . 13
4.2.5.3 Conformance . 13
4.2.6 Sensitivity variation over the operating frequency range. 13
4.2.6.1 Definition . 13
4.2.6.2 Limits . 13
4.2.6.3 Conformance . 13
4.2.7 RF selectivity and spurious response rejection . 13
4.2.7.1 Definition . 13
4.2.7.2 Limits . 13
4.2.7.3 Conformance . 14
4.2.8 Inter-modulation response rejection . 14
4.2.8.1 Definition . 14
4.2.8.2 Limits . 14
4.2.8.3 Conformance . 14
4.2.9 Co-channel rejection . 14
4.2.9.1 Definition . 14
4.2.9.2 Limits . 14
4.2.9.3 Conformance . 14
4.2.10 Blocking . 14
4.2.10.1 Definition . 14
4.2.10.2 Limits . 14
4.2.10.3 Conformance . 15
4.2.11 Sensitivity . 15
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
4.2.11.1 Definition . 15
4.2.11.2 Limits . 15
4.2.11.3 Conformance . 15
4.2.12 Receiver spurious emissions . 15
4.2.12.1 Definition . 15
4.2.12.2 Limits . 15
4.2.12.3 Conformance . 15
5 Testing for compliance with technical requirements . 15
5.1 Environmental conditions for testing . 15
5.1.1 General requirements . 15
5.1.2 Procedure for Tests . 16
5.1.2.1 All Equipment . 16
5.1.2.2 Equipment including Transmitters . 16
5.2 Interpretation of the measurement results . 16
5.3 Test and General Conditions . 16
5.3.1 Transmitter test signals . 16
5.3.1.1 General Considerations . 16
5.3.1.2 Test signal 1 . 16
5.3.1.3 Test signal 2 . 17
5.3.2 Simulated received signals . 17
5.3.2.1 General Considerations . 17
5.3.2.2 Test signal 3 . 17
5.3.2.3 Test signal 4 . 18
5.4 Transmitter tests . 18
5.4.1 Operating frequency and frequency error . 18
5.4.1.1 Description . 18
5.4.1.2 Test conditions . 18
5.4.1.3 Method of measurement . 18
5.4.1.4 Measurement procedure . 18
5.4.2 Spectrum mask . 19
5.4.2.1 Description . 19
5.4.2.2 Test conditions . 19
5.4.2.3 Method of measurement . 19
5.4.2.4 Measurement procedure . 19
5.4.3 Residual Power Output . 20
5.4.3.1 Description . 20
5.4.3.2 Test conditions . 20
5.4.3.3 Method of measurement . 20
5.4.3.4 Measurement procedure . 20
5.4.4 Spurious emissions of transmitter in active mode . 21
5.4.4.1 Description . 21
5.4.4.2 Test conditions . 21
5.4.4.3 Method of measurement . 21
5.4.4.4 Measurement Procedure . 21
5.5 Receiver Tests . 22
5.5.1 Sensitivity variation over the operating frequency range. 22
5.5.1.1 Description . 22
5.5.1.2 Test conditions . 22
5.5.1.3 Method of measurement . 22
5.5.1.4 Measurement procedure . 22
5.5.2 RF selectivity and spurious response rejection . 23
5.5.2.1 Description . 23
5.5.2.2 Test conditions . 23
5.5.2.3 Method of measurement . 23
5.5.2.4 Measurement procedure . 23
5.5.3 Inter-modulation response rejection . 23
5.5.3.1 Description . 23
5.5.3.2 Test conditions . 24
5.5.3.3 Method of measurement . 24
5.5.3.4 Measurement procedure . 24
5.5.4 Co-channel rejection . 25
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
5.5.4.1 Description . 25
5.5.4.2 Test conditions . 25
5.5.4.3 Method of measurement . 25
5.5.4.4 Measurement procedure . 25
5.5.5 Blocking . 26
5.5.5.1 Description . 26
5.5.5.2 Test conditions . 26
5.5.5.3 Method of measurement . 26
5.5.5.4 Measurement procedure . 26
5.5.6 Receiver spurious emissions . 27
5.5.6.1 Description . 27
5.5.6.2 Test conditions . 27
5.5.6.3 Method of measurement . 27
5.5.6.4 Measurement Procedure . 27
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 28
Annex B (informative): Bibliography . 30
Annex C (informative): Change history . 31
History . 32
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C (2015) 5376 final [i.3] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in Table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 5, sub-part 1, of a multi-part deliverable covering Advanced Surface Movement Guidance
and Control System (A-SMGCS), as identified below.
Part 1: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS surveillance service including external interfaces";
Part 2: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS airport safety support service";
Part 3: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for a deployed cooperative sensor including its interfaces";
Part 4: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for a deployed non-cooperative sensor including its interfaces";
Part 5: "Harmonised Standard for access to radio spectrum for multilateration equipment":
Sub-part 1: "Receivers and Interrogators";
Sub-part 2: "Reference and vehicle transmitters";
Part 6: "Harmonised Standard for access to radio spectrum for deployed surface movement radar sensors";
Part 7: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS routing service";
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
Part 8: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS guidance service".
National transposition dates
Date of adoption of this EN: 9 March 2020
Date of latest announcement of this EN (doa): 30 June 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2020
Date of withdrawal of any conflicting National Standard (dow): 31 December 2021
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
A-SMGCS are systems providing routing, guidance, surveillance and control to aircraft and affected vehicles in order to
maintain movement rate under all local weather conditions within the Aerodrome Visibility Operational Level (AVOL)
whilst maintaining the required level of safety.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 303 213-5-1 V1.1.1 (2020-03)
1 Scope
The present document specifies technical characteristics and methods of measurements for the following equipment:
1) Interrogators transmitting in the 1 030 MHz band, used in Mode S multilateration equipment in an Advanced
Surface Movement Guidance and Control System (A-SMGCS).
2) Receivers, receiving in the 1 090 MHz band, used in Mode S multilateration equipment in an Advanced
Surface Movement Guidance and Control System (A-SMGCS).
Antennas for this equipment are external and passive without an additional amplifier.
The present document does not apply to equipment which includes a transponder function, to grou
...
Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
HARMONISED EUROPEAN STANDARD
Advanced Surface Movement Guidance and
Control System (A-SMGCS);
Part 5: Harmonised Standard for access to
radio spectrum for Multilateration (MLAT) equipment;
Sub-part 1: Receivers and Interrogators
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
Reference
DEN/ERM-TGAERO-37-5-1
Keywords
aeronautical, harmonised standard,
interoperability, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.1 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance Requirements . 11
4.2.1 Applicability . 11
4.2.1.1 Equipment with multiple functions . 11
4.2.2 Transmitter operating frequency and frequency error . 11
4.2.2.1 Definition . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.2.3 Spectrum mask . 11
4.2.3.1 Definition . 11
4.2.3.2 Limits . 11
4.2.3.3 Conformance . 12
4.2.4 Residual Power Output . 12
4.2.4.1 Definition . 12
4.2.4.2 Limits . 12
4.2.4.3 Conformance . 12
4.2.5 Spurious emissions of transmitter in active mode . 12
4.2.5.1 Definition . 12
4.2.5.2 Limits . 13
4.2.5.3 Conformance . 13
4.2.6 Sensitivity variation over the operating frequency range. 13
4.2.6.1 Definition . 13
4.2.6.2 Limits . 13
4.2.6.3 Conformance . 13
4.2.7 RF selectivity and spurious response rejection . 13
4.2.7.1 Definition . 13
4.2.7.2 Limits . 13
4.2.7.3 Conformance . 14
4.2.8 Inter-modulation response rejection . 14
4.2.8.1 Definition . 14
4.2.8.2 Limits . 14
4.2.8.3 Conformance . 14
4.2.9 Co-channel rejection . 14
4.2.9.1 Definition . 14
4.2.9.2 Limits . 14
4.2.9.3 Conformance . 14
4.2.10 Blocking . 14
4.2.10.1 Definition . 14
4.2.10.2 Limits . 14
4.2.10.3 Conformance . 15
4.2.11 Sensitivity . 15
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
4.2.11.1 Definition . 15
4.2.11.2 Limits . 15
4.2.11.3 Conformance . 15
4.2.12 Receiver spurious emissions . 15
4.2.12.1 Definition . 15
4.2.12.2 Limits . 15
4.2.12.3 Conformance . 15
5 Testing for compliance with technical requirements . 16
5.1 Environmental conditions for testing . 16
5.1.1 General requirements . 16
5.1.2 Procedure for Tests . 16
5.1.2.1 All Equipment . 16
5.1.2.2 Equipment including Transmitters . 16
5.2 Interpretation of the measurement results . 16
5.3 Test and General Conditions . 16
5.3.1 Transmitter test signals . 16
5.3.1.1 General Considerations . 16
5.3.1.2 Test signal 1 . 17
5.3.1.3 Test signal 2 . 17
5.3.2 Simulated received signals . 17
5.3.2.1 General Considerations . 17
5.3.2.2 Test signal 3 . 18
5.3.2.3 Test signal 4 . 18
5.4 Transmitter tests . 18
5.4.1 Operating frequency and frequency error . 18
5.4.1.1 Description . 18
5.4.1.2 Test conditions . 18
5.4.1.3 Method of measurement . 18
5.4.1.4 Measurement procedure . 19
5.4.2 Spectrum mask . 19
5.4.2.1 Description . 19
5.4.2.2 Test conditions . 19
5.4.2.3 Method of measurement . 19
5.4.2.4 Measurement procedure . 19
5.4.3 Residual power output . 20
5.4.3.1 Description . 20
5.4.3.2 Test conditions . 20
5.4.3.3 Method of measurement . 20
5.4.3.4 Measurement procedure . 20
5.4.4 Spurious emissions of transmitter in active mode . 21
5.4.4.1 Description . 21
5.4.4.2 Test conditions . 21
5.4.4.3 Method of measurement . 21
5.4.4.4 Measurement Procedure . 21
5.5 Receiver Tests . 22
5.5.1 Sensitivity variation over the operating frequency range. 22
5.5.1.1 Description . 22
5.5.1.2 Test conditions . 22
5.5.1.3 Method of measurement . 22
5.5.1.4 Measurement procedure . 22
5.5.2 RF selectivity and spurious response rejection . 23
5.5.2.1 Description . 23
5.5.2.2 Test conditions . 23
5.5.2.3 Method of measurement . 23
5.5.2.4 Measurement procedure . 23
5.5.3 Inter-modulation response rejection . 24
5.5.3.1 Description . 24
5.5.3.2 Test conditions . 24
5.5.3.3 Method of measurement . 24
5.5.3.4 Measurement procedure . 24
5.5.4 Co-channel rejection . 25
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
5.5.4.1 Description . 25
5.5.4.2 Test conditions . 25
5.5.4.3 Method of measurement . 25
5.5.4.4 Measurement procedure . 25
5.5.5 Blocking . 26
5.5.5.1 Description . 26
5.5.5.2 Test conditions . 26
5.5.5.3 Method of measurement . 26
5.5.5.4 Measurement procedure . 26
5.5.6 Receiver spurious emissions . 27
5.5.6.1 Description . 27
5.5.6.2 Test conditions . 27
5.5.6.3 Method of measurement . 27
5.5.6.4 Measurement Procedure . 27
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 29
Annex B (informative): Bibliography . 31
Annex C (informative): Change history . 32
History . 33
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C (2015) 5376 final [i.3] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in Table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 5, sub-part 1, of a multi-part deliverable covering Advanced Surface Movement Guidance
and Control System (A-SMGCS), as identified below.
Part 1: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS surveillance service including external interfaces";
Part 2: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS airport safety support service";
Part 3: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for a deployed cooperative sensor including its interfaces";
Part 4: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for a deployed non-cooperative sensor including its interfaces";
Part 5: "Harmonised Standard for access to radio spectrum for multilateration equipment":
Sub-part 1: "Receivers and Interrogators";
Sub-part 2: "Reference and vehicle transmitters".
Part 6: "Harmonised Standard for access to radio spectrum for deployed surface movement radar sensors";
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
Part 7: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS routing service";
Part 8: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS guidance service".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
A-SMGCS are systems providing routing, guidance, surveillance and control to aircraft and affected vehicles in order to
maintain movement rate under all local weather conditions within the Aerodrome Visibility Operational Level (AVOL)
whilst maintaining the required level of safety.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
1 Scope
The present document specifies technical characteristics and methods of measurements for the following equipment:
1) Interrogators transmitting in the 1 030 MHz band, used in Mode S multilateration equipment in an Advanced
Surface Movement Guidance and Control System (A-SMGCS);
2) Receivers, receiving in the 1 090 MHz band, used in Mode S multilateration equipment in an Advanced
Surface Movement Guidance and Control System (A-SMGCS).
Antennas f
...
SLOVENSKI STANDARD
oSIST prEN 303 213-5-1 V1.0.0:2020
01-februar-2020
Napredni sistem za vodenje in nadzor gibanja po zemlji (A-SMGCS) - 5. del:
Harmonizirani standard za dostop do radijskega spektra za večplastno (MLAT)
opremo - 1. poddel: Sprejemniki in bralniki
Advanced Surface Movement Guidance and Control System (A-SMGCS) - Part 5:
Harmonised Standard for access to radio spectrum for Multilateration (MLAT) equipment
- Sub-part 1: Receivers and Interrogators
Ta slovenski standard je istoveten z: ETSI EN 303 213-5-1 V1.0.0 (2019-12)
ICS:
03.220.50 Zračni transport Air transport
49.090 Oprema in instrumenti v On-board equipment and
zračnih in vesoljskih plovilih instruments
oSIST prEN 303 213-5-1 V1.0.0:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 303 213-5-1 V1.0.0:2020
---------------------- Page: 2 ----------------------
oSIST prEN 303 213-5-1 V1.0.0:2020
Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
HARMONISED EUROPEAN STANDARD
Advanced Surface Movement Guidance and
Control System (A-SMGCS);
Part 5: Harmonised Standard for access to
radio spectrum for Multilateration (MLAT) equipment;
Sub-part 1: Receivers and Interrogators
---------------------- Page: 3 ----------------------
oSIST prEN 303 213-5-1 V1.0.0:2020
2 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
Reference
DEN/ERM-TGAERO-37-5-1
Keywords
aeronautical, harmonised standard,
interoperability, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 303 213-5-1 V1.0.0:2020
3 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.1 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance Requirements . 11
4.2.1 Applicability . 11
4.2.1.1 Equipment with multiple functions . 11
4.2.2 Transmitter operating frequency and frequency error . 11
4.2.2.1 Definition . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.2.3 Spectrum mask . 11
4.2.3.1 Definition . 11
4.2.3.2 Limits . 11
4.2.3.3 Conformance . 12
4.2.4 Residual Power Output . 12
4.2.4.1 Definition . 12
4.2.4.2 Limits . 12
4.2.4.3 Conformance . 12
4.2.5 Spurious emissions of transmitter in active mode . 12
4.2.5.1 Definition . 12
4.2.5.2 Limits . 13
4.2.5.3 Conformance . 13
4.2.6 Sensitivity variation over the operating frequency range. 13
4.2.6.1 Definition . 13
4.2.6.2 Limits . 13
4.2.6.3 Conformance . 13
4.2.7 RF selectivity and spurious response rejection . 13
4.2.7.1 Definition . 13
4.2.7.2 Limits . 13
4.2.7.3 Conformance . 14
4.2.8 Inter-modulation response rejection . 14
4.2.8.1 Definition . 14
4.2.8.2 Limits . 14
4.2.8.3 Conformance . 14
4.2.9 Co-channel rejection . 14
4.2.9.1 Definition . 14
4.2.9.2 Limits . 14
4.2.9.3 Conformance . 14
4.2.10 Blocking . 14
4.2.10.1 Definition . 14
4.2.10.2 Limits . 14
4.2.10.3 Conformance . 15
4.2.11 Sensitivity . 15
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 303 213-5-1 V1.0.0:2020
4 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
4.2.11.1 Definition . 15
4.2.11.2 Limits . 15
4.2.11.3 Conformance . 15
4.2.12 Receiver spurious emissions . 15
4.2.12.1 Definition . 15
4.2.12.2 Limits . 15
4.2.12.3 Conformance . 15
5 Testing for compliance with technical requirements . 16
5.1 Environmental conditions for testing . 16
5.1.1 General requirements . 16
5.1.2 Procedure for Tests . 16
5.1.2.1 All Equipment . 16
5.1.2.2 Equipment including Transmitters . 16
5.2 Interpretation of the measurement results . 16
5.3 Test and General Conditions . 16
5.3.1 Transmitter test signals . 16
5.3.1.1 General Considerations . 16
5.3.1.2 Test signal 1 . 17
5.3.1.3 Test signal 2 . 17
5.3.2 Simulated received signals . 17
5.3.2.1 General Considerations . 17
5.3.2.2 Test signal 3 . 18
5.3.2.3 Test signal 4 . 18
5.4 Transmitter tests . 18
5.4.1 Operating frequency and frequency error . 18
5.4.1.1 Description . 18
5.4.1.2 Test conditions . 18
5.4.1.3 Method of measurement . 18
5.4.1.4 Measurement procedure . 19
5.4.2 Spectrum mask . 19
5.4.2.1 Description . 19
5.4.2.2 Test conditions . 19
5.4.2.3 Method of measurement . 19
5.4.2.4 Measurement procedure . 19
5.4.3 Residual power output . 20
5.4.3.1 Description . 20
5.4.3.2 Test conditions . 20
5.4.3.3 Method of measurement . 20
5.4.3.4 Measurement procedure . 20
5.4.4 Spurious emissions of transmitter in active mode . 21
5.4.4.1 Description . 21
5.4.4.2 Test conditions . 21
5.4.4.3 Method of measurement . 21
5.4.4.4 Measurement Procedure . 21
5.5 Receiver Tests . 22
5.5.1 Sensitivity variation over the operating frequency range. 22
5.5.1.1 Description . 22
5.5.1.2 Test conditions . 22
5.5.1.3 Method of measurement . 22
5.5.1.4 Measurement procedure . 22
5.5.2 RF selectivity and spurious response rejection . 23
5.5.2.1 Description . 23
5.5.2.2 Test conditions . 23
5.5.2.3 Method of measurement . 23
5.5.2.4 Measurement procedure . 23
5.5.3 Inter-modulation response rejection . 24
5.5.3.1 Description . 24
5.5.3.2 Test conditions . 24
5.5.3.3 Method of measurement . 24
5.5.3.4 Measurement procedure . 24
5.5.4 Co-channel rejection . 25
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 303 213-5-1 V1.0.0:2020
5 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
5.5.4.1 Description . 25
5.5.4.2 Test conditions . 25
5.5.4.3 Method of measurement . 25
5.5.4.4 Measurement procedure . 25
5.5.5 Blocking . 26
5.5.5.1 Description . 26
5.5.5.2 Test conditions . 26
5.5.5.3 Method of measurement . 26
5.5.5.4 Measurement procedure . 26
5.5.6 Receiver spurious emissions . 27
5.5.6.1 Description . 27
5.5.6.2 Test conditions . 27
5.5.6.3 Method of measurement . 27
5.5.6.4 Measurement Procedure . 27
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 29
Annex B (informative): Bibliography . 31
Annex C (informative): Change history . 32
History . 33
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 303 213-5-1 V1.0.0:2020
6 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C (2015) 5376 final [i.3] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in Table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 5, sub-part 1, of a multi-part deliverable covering Advanced Surface Movement Guidance
and Control System (A-SMGCS), as identified below.
Part 1: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS surveillance service including external interfaces";
Part 2: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS airport safety support service";
Part 3: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for a deployed cooperative sensor including its interfaces";
Part 4: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for a deployed non-cooperative sensor including its interfaces";
Part 5: "Harmonised Standard for access to radio spectrum for multilateration equipment":
Sub-part 1: "Receivers and Interrogators";
Sub-part 2: "Reference and vehicle transmitters".
Part 6: "Harmonised Standard for access to radio spectrum for deployed surface movement radar sensors";
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 303 213-5-1 V1.0.0:2020
7 Draft ETSI EN 303 213-5-1 V1.0.0 (2019-12)
Part 7: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS routing service";
Part 8: "Community Specification for application under the Single European Sky Interoperability Regulation EC
552/2004 for A-SMGCS guidance service".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Mo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.