SIST EN 16898:2022
(Main)Safety and control devices for gas burners and gas burning appliances - Gas filters having a maximum working pressure up to and including 600 kPa
Safety and control devices for gas burners and gas burning appliances - Gas filters having a maximum working pressure up to and including 600 kPa
This European Standard specifies the safety, design, construction, and performance requirements and testing for gas filters for burners and appliances burning one or more gaseous fuels.
This European Standard is applicable to:
— gas filters with declared maximum inlet pressure up to and including 600 kPa, of nominal connection size up to and including DN 250 for use with one or more fuel gases in accordance with EN 437:2009;
— gas filters specified as pressure accessories as defined by EU Directive 2014/68/EU (see Annex F).
NOTE 1 For pressure accessories, the requirements of EN 13611:2019, Annex F also apply.
NOTE 2 Requirements for pressures above 500 kPa are considered in sub-clause 6.3.1 by referring to EN 13611:2019, Annexes F to H.
This European Standard is not applicable to gas filters that are connected directly to mains pipe-work or to a container that maintains a standard distribution pressure.
Sicherheits- und Regeleinrichtungen für Gasbrenner und Gasbrennstoffgeräte - Gasfilter für einen Betriebsdruck bis einschließlich 600 kPa
Dieses Dokument legt die Sicherheits-, Konstruktions- und Funktionsanforderungen sowie die Prüfung für Gasfilter für Brenner und Brennstoffgeräte für einen oder mehrere gasförmige(n) Brennstoff(e) fest.
Dieses Dokument ist anwendbar auf:
— Gasfilter mit einem angegebenen höchsten Eingangsdruck bis einschließlich 600 kPa mit Anschlussnennweiten bis einschließlich DN 250 zur Verwendung mit einem oder mehreren Brenngas(en) nach EN 437:2009;
— Gasfilter, die als druckhaltende Ausrüstungsteile nach EU-Richtlinie 2014/68/EU festgelegt sind (siehe Anhang F).
ANMERKUNG 1 Für druckhaltende Ausrüstungsteile gelten ebenfalls die Anforderungen nach EN 13611:2019, Anhang F.
ANMERKUNG 2 Anforderungen für Drücke über 500 kPa werden in Unterabschnitt 6.3.1 in Bezug auf EN 13611:2019, Anhang F bis H berücksichtigt.
Dieses Dokument gilt nicht für Gasfilter, die direkt an die Gasversorgungsleitung angeschlossen sind, oder für einen Behälter, der einen Standardverteilungsdruck aufrechterhält.
Équipements auxiliaires pour brûleurs à gaz et appareils à gaz - Filtres à gaz ayant une pression de service maximale inférieure ou égale à 600 kPa
L’article 1 de la norme EN13611 :2019 s’applique avec la modification et l’addition suivantes :
Modification :
Le 1er paragraphe de l’article 1 de la norme EN13611 :2019 est remplacé par ce qui suit :
Le présent document spécifie les exigences en matière de sécurité, de conception, de construction et de performance ainsi que les essais applicables aux filtres à gaz pour brûleurs et appareils.
Le présent document est applicable aux filtres à gaz dont la pression amont maximale déclarée est inférieure ou égale à 600 kPa, de diamètre nominal de raccordement inférieur ou égal à DN 250 et conçus pour une utilisation avec un ou plusieurs combustibles gazeux.
Addition :
Le présent document ne s'applique pas :
- aux filtres à gaz qui sont raccordés directement au réseau de distribution ou à un conteneur qui maintient en aval une pression de distribution normalisée.
Le 4ième paragraphe de l’article 1 de la EN 13611 :2019 est supprimé.
Varnostne in nadzorne naprave za plinske gorilnike in plinske aparate - Filtri plina za najvišji delovni tlak do vključno 600 kPa
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 16898:2022
01-december-2022
Varnostne in nadzorne naprave za plinske gorilnike in plinske aparate - Filtri plina
za najvišji delovni tlak do vključno 600 kPa
Safety and control devices for gas burners and gas burning appliances - Gas filters
having a maximum working pressure up to and including 600 kPa
Sicherheits- und Regeleinrichtungen für Gasbrenner und Gasbrennstoffgeräte - Gasfilter
für einen Betriebsdruck bis einschließlich 600 kPa
Équipements auxiliaires pour brûleurs à gaz et appareils à gaz - Filtres à gaz ayant une
pression de service maximale inférieure ou égale à 600 kPa
Ta slovenski standard je istoveten z: EN 16898:2022
ICS:
27.060.20 Plinski gorilniki Gas fuel burners
SIST EN 16898:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 16898:2022
---------------------- Page: 2 ----------------------
SIST EN 16898:2022
EN 16898
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2022
EUROPÄISCHE NORM
ICS 27.060.20
English Version
Safety and control devices for gas burners and gas burning
appliances - Gas filters having a maximum working
pressure up to and including 600 kPa
Équipements auxiliaires pour brûleurs à gaz et Sicherheits- und Regeleinrichtungen für Gasbrenner
appareils à gaz - Filtres à gaz ayant une pression de und Gasbrennstoffgeräte - Gasfilter für einen
service maximale inférieure ou égale à 600 kPa Betriebsdruck bis einschließlich 600 kPa
This European Standard was approved by CEN on 1 August 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16898:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 16898:2022
EN 16898:2022 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Classification . 8
4.1 Classes of control . 8
4.2 Groups of control . 8
4.3 Classes of control functions . 8
4.4 Types of DC supplied controls . 8
5 Test conditions and uncertainty of measurements . 8
6 Design and construction . 8
6.1 General . 8
6.2 Mechanical parts of the control . 8
6.3 Materials . 10
6.4 Gas connections . 10
6.5 Electrical parts of the control . 11
6.6 Protection against internal faults for the purpose of functional safety . 11
7 Performance . 11
7.1 General . 11
7.2 Leak-tightness . 11
7.3 Torsion and bending . 11
7.4 Rated flow rate . 11
7.5 Durability . 11
7.6 Performance tests for electronic controls . 11
7.7 Long-term performance for electronic controls . 12
7.8 Data exchange . 12
7.101 Filtration efficiency according to test dust . 12
8 Electrical requirements . 14
9 Electromagnetic compatibility (EMC) . 14
10 Marking, instructions . 14
10.1 Marking . 14
10.2 Instructions . 14
10.3 Warning notice . 15
Annex A (informative) Abbreviations and symbols . 16
Annex B (informative) Leak-tightness test for gas controls – volumetric method . 17
Annex C (informative) Leak-tightness test for gas controls – pressure loss method . 18
Annex D (normative) Calculation of pressure loss into leakage rate . 19
Annex E (normative) Electrical/electronic component fault modes . 20
Annex F (normative) Additional requirements for safety accessories and pressure
accessories as defined in EU Directive 2014/68/EU . 21
2
---------------------- Page: 4 ----------------------
SIST EN 16898:2022
EN 16898:2022 (E)
Annex G (normative) Materials for pressurized parts . 22
Annex H (normative) Additional materials for pressurized parts . 23
Annex I (normative) Requirements for controls used in DC supplied burners and
appliances burning gaseous or liquid fuels. 24
Annex J (normative) Method for the determination of a Safety Integrity Level (SIL) . 25
Annex K (normative) Method for the determination of a Performance Level (PL) . 26
Annex L (informative) Relationship between Safety Integrity Level (SIL) and Performance
Level (PL) . 27
Annex M (normative) Reset functions . 28
Annex N (informative) Guidance document on Environmental Aspects . 29
Annex O (normative) Seals of elastomer, cork and synthetic fibre mixtures . 30
Annex AA (normative) Dust collecting device . 31
AA.1 General . 31
AA.2 Dust collecting bag . 31
AA.3 Outlet filter . 31
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Regulation (EU) 2016/426 aimed to be covered . 32
Bibliography . 35
3
---------------------- Page: 5 ----------------------
SIST EN 16898:2022
EN 16898:2022 (E)
European foreword
This document (EN 16898:2022) has been prepared by Technical Committee CEN/TC 58 “Safety and
control devices for burners and appliances burning gaseous or liquid fuels”, the secretariat of which is
held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2023, and conflicting national standards shall be
withdrawn at the latest by October 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral part
of this document.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
4
---------------------- Page: 6 ----------------------
SIST EN 16898:2022
EN 16898:2022 (E)
Introduction
This document is intended to be used in conjunction with EN 13611:2019.
EN 13611:2019 recognizes the safety level specified by CEN/TC 58 and is regarded as a horizontal
standard dealing with the safety, construction, performance and testing of controls for burners and
appliances burning gaseous and/or liquid fuels.
The general requirements for controls are given in EN 13611:2019, and methods for classification and
assessment for new controls and control functions are given in EN 14459:2021 (see Figure 1).
EN 126:2012 (see Figure 1) specifies multifunctional controls combining two or more controls and
Application Control Functions, one of which is a mechanical control function. The requirements for
controls and Application Control Functions are given in the specific control standard (see Figure 1,
control functions).
Figure 1 — Interrelation of control standards
EN 13611:2019 should be used in conjunction with the specific standard for a specific type of control (e.g.
EN 88-1:2022, EN 88-2:2022, EN 88-3:2022, EN 125:2022, EN 126:2012, EN 161:2022, EN 257:2022,
1
EN 298:2022, EN 1106:2022, EN 1643:2022, EN 1854:— , EN 12067-2:2022, EN 16304:2022,
EN 16340:2014, EN 16678:2022 and EN 16898:2022), or for controls for specific applications.
EN 13611:2019 can also be applied, so far as reasonable, to controls not mentioned in a specific standard
and to controls designed on new principles, in which case additional requirements can be necessary.
EN 14459:2021 provides methods for classification and assessment of new control principles.
Primarily in industrial applications it is common practice to rate the safety of a plant based on values
describing the likelihood of a dangerous failure. These values are being used to determine Safety Integrity
Levels or Performance Levels when the system is being assessed in its entirety.
CEN/TC 58 standards for safety relevant controls do go beyond this approach, because for a certain life
time for which the product is specified, designed and tested a dangerous failure is not allowed at all.
Failure modes are described and assessed in greater detail.
1
Under preparation. Stage at the time of publication: FprEN 1854:2022.
5
---------------------- Page: 7 ----------------------
SIST EN 16898:2022
EN 16898:2022 (E)
Measures to prevent from dangerous situations are defined. Field experience over many decades is
reflected in the CEN/TC 58 standards. Requirements of EN 13611:2019 can be considered as proven in
practice.
This document refers to clauses of EN 13611:2019 or adapts clauses by stating “with the following
modification”, “with the following addition”, “is replaced by the following” or “is not applicable” in the
corresponding clause.
This document adds clauses or subclauses to the structure of EN 13611:2019 which are particular to this
document. Subclauses which are additional to those in EN 13611:2019 are numbered starting from 101.
Additional annexes are designated as Annex AA, Annex BB, Annex CC etc. It should be noted that these
clauses, subclauses and annexes are not indicated as an addition.
6
---------------------- Page: 8 ----------------------
SIST EN 16898:2022
EN 16898:2022 (E)
1 Scope
EN 13611:2019, Clause 1 applies with the following modification and addition:
Modification:
st
The 1 paragraph of EN 13611:2019, Clause 1 is replaced by:
This document specifies the safety, design, construction, and performance requirements and testing for
gas filters for burners and appliances burning one or more gaseous fuels.
This document is applicable to gas filters with declared maximum inlet pressures up to and including
600 kPa and of nominal connection sizes up to and including DN 250.
Addition:
This document is not applicable to:
— gas filters that are connected directly to mains pipe-work or to a container that maintains a standard
distribution pressure.
th
The 4 paragraph of EN 13611:2019, Clause 1 is removed.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 16890-1:2016, Air filters for general ventilation — Part 1: Technical specifications, requirements
and classification system based upon particulate matter efficiency (ePM) (ISO 16890-1:2016)
2
EN 13611:2019 , Safety and control devices for burners and appliances burning gaseous and/or liquid fuels
— General requirements
3
EN 60312-1:2017 , Vacuum cleaners for household use — Part 1: Dry vacuum cleaners — Methods for
measuring the performance (IEC 60312-1:2010, modified)
ISO 12103-1:2016, Road vehicles — Test contaminants for filter evaluation — Part 1: Arizona test dust
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 13611:2019 and the following
apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at https://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
2
As impacted by EN 13611:2019/AC:2021.
3
As impacted by EN 60312-1:2017/A11:2022.
7
---------------------- Page: 9 ----------------------
SIST EN 16898:2022
EN 16898:2022 (E)
3.1
gas filter
device that segregates particles from the gas flow e.g. dust and rust
3.2
filter material
part of the filter, which segregates particles
3.3
filter element
filter material with support
3.4
filtration efficiency
percentage ratio of filtered amount of dust to charged amount of dust
4 Classification
...
SLOVENSKI STANDARD
oSIST prEN 16898:2020
01-maj-2020
Varnostne in nadzorne naprave za plinske gorilnike in plinske aparate - Filtri plina
za najvišji delovni tlak do vključno 600 kPa
Safety and control devices for gas burners and gas burning appliances - Gas filters
having a maximum working pressure up to and including 600 kPa
Sicherheits- und Regeleinrichtungen für Gasbrenner und Gasbrennstoffgeräte - Gasfilter
für einen Betriebsdruck bis einschließlich 600 kPa
Ta slovenski standard je istoveten z: prEN 16898
ICS:
27.060.20 Plinski gorilniki Gas fuel burners
oSIST prEN 16898:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 16898:2020
---------------------- Page: 2 ----------------------
oSIST prEN 16898:2020
DRAFT
EUROPEAN STANDARD
prEN 16898
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2020
ICS
English Version
Safety and control devices for gas burners and gas burning
appliances - Gas filters having a maximum working
pressure up to and including 600 kPa
Sicherheits- und Regeleinrichtungen für Gasbrenner
und Gasbrennstoffgeräte - Gasfilter für einen
Betriebsdruck bis einschließlich 600 kPa
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 58.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16898:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 16898:2020
prEN 16898:2020 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Classification . 7
4.1 Classes of control . 7
4.2 Groups of control . 7
4.3 Classes of control functions . 7
4.4 Types of DC supplied controls . 7
5 Test conditions and uncertainty of measurements . 7
6 Design and construction . 7
6.1 General . 7
6.2 Mechanical parts of the control . 7
6.2.1 Appearance . 7
6.2.2 Holes . 7
6.2.3 Breather holes . 7
6.2.4 Screwed fastenings . 7
6.2.5 Jointing . 7
6.2.6 Moving parts . 8
6.2.7 Sealing caps . 8
6.2.8 Dismantling and reassembly . 8
6.2.9 Auxiliary canals and orifices . 8
6.2.10 Presetting device . 8
6.3 Materials . 8
6.3.1 General material requirements . 8
6.3.2 Housing . 8
6.3.3 Zinc alloys . 9
6.3.4 Springs . 9
6.3.5 Resistance to corrosion and surface protection . 9
6.3.6 Impregnation . 9
6.3.7 Seals for glands for moving parts . 9
6.4 Gas Connections . 9
6.4.1 Making connections. 9
6.4.2 Connection sizes . 9
6.4.3 Threads . 9
6.4.4 Union joints . 9
6.4.5 Flanges . 9
6.4.6 Compression fittings . 9
6.4.7 Nipples for pressure test . 9
6.4.8 Strainers . 9
6.5 Electrical parts of the control . 9
6.6 Protection against internal faults for the purpose of functional safety . 9
7 Performance . 10
7.1 General . 10
7.2 Leak-tightness . 10
2
---------------------- Page: 4 ----------------------
oSIST prEN 16898:2020
prEN 16898:2020 (E)
7.2.1 Requirements . 10
7.2.2 Test . 10
7.3 Torsion and bending . 10
7.3.1 General . 10
7.3.2 Torsion and bending moments . 10
7.4 Rated flow rate . 10
7.5 Durability. 10
7.6 Performance tests for electronic controls . 10
7.7 Long-term performance for electronic controls . 10
7.8 Data exchange . 10
8 Electrical requirements . 13
9 Electromagnetic compatibility (EMC) . 13
10 Marking, instructions . 13
10.1 Marking . 13
10.2 Instructions . 13
10.3 Warning Notice . 14
Annex A (informative) Abbreviations and Symbols . 15
Annex B (informative) Leak-tightness test for gas controls – volumetric method . 16
Annex C (informative) Leak-tightness test for gas controls – pressure loss method . 17
Annex D (normative) Conversion of pressure loss into leakage rate . 18
Annex E (normative) Electrical/electronic component fault modes . 19
Annex F (normative) Additional requirements for safety accessories and pressure
accessories as defined in EU Directive 2014/68/EU. 20
Annex G (normative) Materials for pressurized parts . 21
Annex H (normative) Additional materials for pressurized parts . 22
Annex I (normative) Requirements for controls used in DC supplied burners and
appliances burning gaseous or liquid fuels. 23
Annex J (normative) Method for the determination of a Safety Integrity Level (SIL) . 24
Annex K (normative) Method for the determination of a Performance Level (PL) . 25
Annex L (informative) Relationship between Safety Integrity Level (SIL) and Performance
Level (PL) . 26
Annex M (normative) Reset functions . 27
Annex N (informative) Guidance document on environmental aspects . 28
Annex O (normative) Seals of elastomer, cork and synthetic fibre mixtures . 29
Annex AA (normative) Dust collecting device . 30
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Regulation (EU) 2016/426 aimed to be covered . 31
Annex ZB (informative) Relationship between this European Standard and the essential
requirements of Directive 2014/68/EU aimed to be covered . 34
Bibliography . 36
3
---------------------- Page: 5 ----------------------
oSIST prEN 16898:2020
prEN 16898:2020 (E)
European foreword
This document (prEN 16898:2020) has been prepared by Technical Committee CEN/TC 58 “Safety and
control devices for burners and appliances burning gaseous or liquid fuels”, the secretariat of which is
held by BSI.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a standardization request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of
EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA or B, which are an integral part of this
document.
4
---------------------- Page: 6 ----------------------
oSIST prEN 16898:2020
prEN 16898:2020 (E)
Introduction
The generic requirements for controls are given in EN 13611:2019 and methods for classification and
assessment for new controls and control functions are given in EN 14459:2015, Clause 1 up to and
including 7.13 (see Figure 1).
The requirements for controls are given in the specific control standard (see Figure 1).
Multifunctional Controls (MFC) according to EN 126:2012 with two or more controls and Application
Control Functions, e.g. the Gas Shut-off Control Function, being inherently multifunctional controls.
Each control integrated in the MFC meets the applicable requirements of the relevant control
standard(s). In addition, EN 126:2012 covers requirements for the safety related interactions between
the different devices.
Figure 1 — Standards house
This control standard refers to clauses of EN 13611:2019 or adapts it by stating “with the following
modification”, “with the following addition”, “is replaced by the following” or “is not applicable” in the
corresponding clause. This document adds clauses or subclauses to the structure of EN 13611:2019
which are particular to this standard. It should be noted that these clauses and subclauses are not
indicated as an addition. Subclauses which are additional to those in EN 13611:2019 are numbered
starting from 101. Additional Annexes are designed as Annex AA, BB, CC, etc.
5
---------------------- Page: 7 ----------------------
oSIST prEN 16898:2020
prEN 16898:2020 (E)
1 Scope
This document specifies the safety, design, construction, and performance requirements and testing for
gas filters for burners and appliances burning one or more gaseous fuels.
This document is applicable to:
— gas filters with declared maximum inlet pressure up to and including 600 kPa, of nominal
connection size up to and including DN 250 for use with one or more fuel gases in accordance with
EN 437:2009;
— gas filters specified as pressure accessories as defined by EU Directive 2014/68/EU (see Annex F).
NOTE 1 For pressure accessories, the requirements of EN 13611:2019, Annex F also apply.
NOTE 2 Requirements for pressures above 500 kPa are considered in subclause 6.3.1 by referring to
EN 13611:2019, Annexes F to H.
This document is not applicable to gas filters that are connected directly to mains pipe-work or to a
container that maintains a standard distribution pressure.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 779:2012, Particulate air filters for general ventilation — Determination of the filtration performance
EN 13611:2019, Safety and control devices for burners and appliances burning gaseous and/or liquid
fuels - General requirements
EN 60312-1:2013, Vacuum cleaners for household use — Part 1: Dry vacuum cleaners — Methods for
measuring the performance (IEC 60312-1:2010, modified + A1:2011, modified)
ISO 12103-1:1997, Road vehicles — Test dust for filter evaluation — Part 1: Arizona test dust
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 13611:2019 and the following
apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1
gas filter
device that segregates particles from the gas flow e.g. dust and rust
3.2
filter material
part of the filter, which segregates particles
6
---------------------- Page: 8 ----------------------
oSIST prEN 16898:2020
prEN 16898:2020 (E)
3.3
filter element
filter material with support
3.4
filtration efficiency
percentage ratio of filtered amount of dust to charged amount of dust
4 Classification
4.1 Classes of control
EN 13611:2019, 4.1 is not applicable.
4.2 Groups of control
Shall be according to EN 13611:2019, 4.2.
4.3 Classes of control functions
EN 13611:2019, 4.3 is not applicable.
4.4 Types of DC supplied controls
EN 13611:2019, 4.4 is not applicable.
5 Test conditions and uncertainty of measurements
Shall be according to EN 13611:2019, Clause 5.
6 Design and construction
6.1 General
Shall be according to EN 13611:2019, 6.1.
6.2 Mechanical parts of the control
6.2.1 Appearance
Shall be according to EN 13611:2019, 6.2.1.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.