SIST EN 60153-4:2018
(Main)Hollow metallic waveguides - Part 4: Relevant specifications for circular waveguides (IEC 60153-4:2017)
Hollow metallic waveguides - Part 4: Relevant specifications for circular waveguides (IEC 60153-4:2017)
This part of IEC 60153 specifies straight hollow metallic tubing of circular waveguides for use
as waveguides in electronic equipment.
The aim of this recommendation is to specify for hollow metallic waveguides:
a) the details necessary to ensure compatibility and, as far as essential, interchangeability;
b) test methods;
c) uniform requirements for the electrical and mechanical properties.
Metallische Hohlleiter - Teil 4: Einzelbestimmungen für Rundhohlleiter
Guides d'ondes métalliques creux - Partie 4: Spécifications applicables aux guides d'ondes circulaires
l'IEC 60153-4:2017 spécifie des tubes métalliques creux rectilignes de guides d'ondes circulaires destinés à être utilisés comme guides d'ondes dans les équipements électroniques.
La présente recommandation a pour but de spécifier pour les guides d'ondes métalliques creux:
a) les détails nécessaires pour assurer la compatibilité et, dès lors que c’est essentiel, l'interchangeabilité;
b) les méthodes d’essai;
c) es exigences uniformes pour les propriétés électriques et mécaniques
La présente édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) Extension et révision de la plage de fréquences de fonctionnement pour les guides d'ondes;
b) Révision des tolérances sur les dimensions d'ouvertures;
c) Révision de la méthode d'essai des dimensions d'ouverture;
d) Révision des équations d'affaiblissement.
Votli kovinski valovodi - 4. del: Ustrezne specifikacije za krožne valovode (IEC 60153-4:2017)
Ta del standarda IEC 60153 določa ravne votle kovinske cevi krožnih valovodov, ki se uporabljajo kot valovodi v elektronski opremi.
S tem priporočilom se za votle kovinske valovode določa:
a) potrebne podrobnosti za zagotovitev združljivosti in, kolikor je nujno, medsebojne zamenljivosti;
b) preskusne metode;
c) enotne zahteve za električne in mehanske lastnosti.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60153-4:2018
01-februar-2018
1DGRPHãþD
SIST HD 123.4 S1:2002
Votli kovinski valovodi - 4. del: Ustrezne specifikacije za krožne valovode (IEC
60153-4:2017)
Hollow metallic waveguides - Part 4: Relevant specifications for circular waveguides (IEC
60153-4:2017)
Ta slovenski standard je istoveten z: EN 60153-4:2017
ICS:
33.120.10 Koaksialni kabli. Valovodi Coaxial cables. Waveguides
SIST EN 60153-4:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60153-4:2018
---------------------- Page: 2 ----------------------
SIST EN 60153-4:2018
EUROPEAN STANDARD EN 60153-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2017
ICS 33.120.10 Supersedes HD 123.4 S1:1977
English Version
Hollow metallic waveguides - Part 4: Relevant specifications for
circular waveguides
(IEC 60153-4:2017)
Guides d'ondes métalliques creux - Partie 4: Spécifications Metallische Hohlleiter - Teil 4: Einzelbestimmungen für
applicables aux guides d'ondes circulaires Rundhohlleiter
(IEC 60153-4:2017) (IEC 60153-4:2017)
This European Standard was approved by CENELEC on 2017-09-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60153-4:2017 E
---------------------- Page: 3 ----------------------
SIST EN 60153-4:2018
EN 60153-4:2017 (E)
European foreword
The text of document 46F/344/CDV, future edition 3 of IEC 60153-4, prepared by SC 46F "RF and
microwave passive components", of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 60153-4:2017.
The following dates are fixed:
• latest date by which the document has to be implemented at (dop) 2018-06-20
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with (dow) 2020-09-20
the document have to be withdrawn
This document supersedes HD 123.4 S1:1977.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60153-4:2017 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60153-1:2016 NOTE Harmonized in EN 60153-1:2016.
ISO/IEC 17025:2005 NOTE Harmonized as EN ISO/IEC 17025:2005.
2
---------------------- Page: 4 ----------------------
SIST EN 60153-4:2018
EN 60153-4:2017 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050-726 1982 International electrotechnical vocabulary - - -
Chapter 726: Transmission lines and
waveguides
IEC 60261 - Sealing test for pressurized waveguide HD 138 S2 -
tubing and assemblies
3
---------------------- Page: 5 ----------------------
SIST EN 60153-4:2018
---------------------- Page: 6 ----------------------
SIST EN 60153-4:2018
IEC 60153-4
®
Edition 3.0 2017-08
INTERNATIONAL
STANDARD
colour
inside
Hollow metallic waveguides –
Part 4: Relevant specifications for circular waveguides
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.120.10 ISBN 978-2-8322-4613-9
Warning! Make sure that you obtained this publication from an authorized distributor.
® Registered trademark of the International Electrotechnical Commission
---------------------- Page: 7 ----------------------
SIST EN 60153-4:2018
– 2 – IEC 60153-4:2017 © IEC 2017
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General . 5
4.1 Standardized types . 5
4.2 Type designation . 5
4.3 Frequency range . 5
5 Mechanical requirements . 6
5.1 General . 6
5.2 Dimensions . 6
5.2.1 Basic diameter and deviations . 6
5.2.2 Basic diameter deviations . 9
5.2.3 Ellipticity . 9
5.2.4 Wall thickness . 9
5.2.5 Eccentricity . 9
5.2.6 Outside dimensions . 9
5.3 Other mechanical requirements . 10
5.3.1 Bow . 10
5.3.2 Surface roughness . 10
5.3.3 Internal stresses . 10
6 Electrical tests – Attenuation . 10
7 Additional tests – Gastightness . 11
Bibliography . 12
Table 1 – Basic diameter and deviations . 7
Table 2 – Circular waveguides . 8
Table 3 – Inner Diameter deviations . 9
Table 3 – Outer diameter deviations . 9
---------------------- Page: 8 ----------------------
SIST EN 60153-4:2018
IEC 60153-4:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
HOLLOW METALLIC WAVEGUIDES –
Part 4: Relevant specifications for circular waveguides
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60153-4 has been prepared by subcommittee 46F: RF and
microwave passive components, of IEC technical committee TC:46: Cables, wires,
waveguides, RF connectors, RF and microwave passive components and accessories.
This third edition cancels and replaces the second edition published in 1973-1. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) Expand and revise the operation frequency range for waveguides;
b) Revise the allowance of aperture dimensions;
c) Revise the test method for aperture dimensions;
d) Revise the equation of attenuation.
---------------------- Page: 9 ----------------------
SIST EN 60153-4:2018
– 4 – IEC 60153-4:2017 © IEC 2017
The text of this International Standard is based on the following documents:
CDV Report on voting
46F/344/CDV 46F/356/RVC
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all the parts in the IEC 60153 series, published under the general title Hollow metallic
waveguides, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
---------------------- Page: 10 ----------------------
SIST EN 60153-4:2018
IEC 60153-4:2017 © IEC 2017 – 5 –
HOLLOW METALLIC WAVEGUIDES –
Part 4: Relevant specifications for circular waveguides
1 Scope
This part of IEC 60153 specifies straight hollow metallic tubing of circular waveguides for use
as waveguides in electronic equipment.
The aim of this recommendation is to specify for hollow metallic waveguides:
a) the details necessary to ensure compatibility and, as far as essential, interchangeability;
b) test methods;
c) uniform requirements for the electrical and mechanical properties.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60050-726:1982, International Electrotechnical Vocabulary. Transmission lines and
waveguides
IEC 60261, Sealing test for pressurized waveguide tubing and assemblies
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60050-726:1982
apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
4 General
4.1 Standardized types
The series of circular waveguides covered by this publication are shown in Tables 1 and 2.
The preferred types are shown in Table 2. As it might be desirable to use circular waveguides
of intermediate sizes, Table 3 has been added in which the latter types are included.
4.2 Type designation
For these waveguides, the type designation comprises:
• The code: 60153 IEC-C
• A number characterizing a particular size of waveguid
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.