SIST EN ISO 23153-2:2020
(Main)Plastics - Polyetheretherketone (PEEK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 23153-2:2020)
Plastics - Polyetheretherketone (PEEK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 23153-2:2020)
This part of ISO xxxxx specifies the methods of preparation of test specimens and the test methods to
be used in determining the properties of polyetheretherketone (PEEK) moulding and extrusion
materials. Requirements for handling test material and for conditioning both the test material before
moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring
properties of the materials from which these specimens are made are also given. Properties and test
methods that are suitable and necessary to characterize PEEK moulding and extrusion materials are
listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods
in wide use for or of particular significance to these moulding and extrusion materials are also included
in this part of ISO xxxxx, as are the designatory properties specified in ISO xxxxx-1.
In order to obtain reproducible and comparable test results, it is necessary to use the methods of
preparation and conditioning, the specimen dimensions and the test procedures specified herein.
Values determined will not necessarily be identical to those obtained using specimens of different
dimensions or prepared using different procedures.
Kunststoffe - Polyetheretherketone (PEEK)-Werkstoffe - Teil 2: Herstellung von Probekörpern und Bestimmung der Eigenschaften (ISO 23153-2:2020)
Dieses Dokument legt die Verfahren zur Herstellung von Probekörpern und die Prüfverfahren, die zur Bestimmung der Eigenschaften von Polyetheretherketon- (PEEK)-Form- und Extrusionswerkstoffen anzuwenden sind, fest. Die Anforderungen an die Behandlung des Prüfmaterials und an das Konditionieren des Prüfmaterials sowohl vor dem Formen als auch der Probekörper vor der Prüfung sind angegeben.
Verfahren und Bedingungen für die Herstellung von Probekörpern sowie Verfahren für die Bestimmung der Eigenschaften der Werkstoffe, aus denen diese Probekörper hergestellt werden, sind ebenfalls angegeben. Eigenschaften und Prüfverfahren, die geeignet und notwendig sind, um PEEK-Form- und Extrusions¬werkstoffe zu charakterisieren, sind aufgeführt.
Um reproduzierbare und vergleichbare Prüfergebnisse zu erhalten, werden die hier festgelegten Verfahren für die Herstellung und Konditionierung, die Probekörpermaße und die Prüfverfahren angewendet. Die ermittelten Werte sind nicht unbedingt identisch mit denen, die an Probekörpern mit anderen Maßen oder an mit anderen Verfahren hergestellten Probekörpern erhalten wurden.
Plastiques - Matériaux à base de polyétheréthercétone (PEEK) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 23153-2:2020)
Le présent document spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai à utiliser pour déterminer les propriétés des matériaux à base de polyétheréthercétone (PEEK) pour moulage et extrusion. Les exigences relatives à la manipulation du matériau d'essai et au conditionnement du matériau d'essai avant moulage et des éprouvettes avant essai sont indiquées.
Les modes opératoires et les conditions nécessaires à la préparation des éprouvettes, ainsi que les modes opératoires de mesure des propriétés des matériaux à partir desquels les éprouvettes sont obtenues sont également donnés. Les propriétés et méthodes d'essai qui sont utiles et nécessaires pour caractériser les matériaux pour moulage et extrusion à base de PEEK sont énumérées.
Dans le but d'obtenir des résultats d'essai reproductibles et comparables, les méthodes de préparation et de conditionnement, les dimensions d'éprouvette ainsi que les modes opératoires d'essai spécifiés ici sont utilisés. Les valeurs déterminées ne seront pas nécessairement identiques à celles obtenues en utilisant des éprouvettes de dimensions différentes ou préparées selon des modes opératoires différents.
Polimerni materiali - Materiali na osnovi polietereterketona (PEEK) za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 23153-2:2020)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 23153-2:2020
01-april-2020
Polimerni materiali - Materiali na osnovi polietereterketona (PEEK) za oblikovanje
in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO
23153-2:2020)
Plastics - Polyetheretherketone (PEEK) moulding and extrusion materials - Part 2:
Preparation of test specimens and determination of properties (ISO 23153-2:2020)
Kunststoffe - Polyetheretherketone (PEEK)-Werkstoffe - Teil 2: Herstellung von
Probekörpern und Bestimmung der Eigenschaften (ISO 23153-2:2020)
Plastiques - Matériaux à base de polyétheréthercétone (PEEK) pour moulage et
extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO
23153-2:2020)
Ta slovenski standard je istoveten z: EN ISO 23153-2:2020
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 23153-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 23153-2:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 23153-2:2020
EN ISO 23153-2
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2020
EUROPÄISCHE NORM
ICS 83.080.20
English Version
Plastics - Polyetheretherketone (PEEK) moulding and
extrusion materials - Part 2: Preparation of test specimens
and determination of properties (ISO 23153-2:2020)
Plastiques - Matériaux à base de polyétheréthercétone Kunststoffe - Polyetheretherketone (PEEK)-Werkstoffe
(PEEK) pour moulage et extrusion - Partie 2: - Teil 2: Herstellung von Probekörpern und
Préparation des éprouvettes et détermination des Bestimmung der Eigenschaften (ISO 23153-2:2020)
propriétés (ISO 23153-2:2020)
This European Standard was approved by CEN on 12 December 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23153-2:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 23153-2:2020
EN ISO 23153-2:2020 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 23153-2:2020
EN ISO 23153-2:2020 (E)
European foreword
This document (EN ISO 23153-2:2020) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2020, and conflicting national standards shall be
withdrawn at the latest by July 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 23153-2:2020 has been approved by CEN as EN ISO 23153-2:2020 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 23153-2:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 23153-2:2020
INTERNATIONAL ISO
STANDARD 23153-2
First edition
2020-01
Plastics — Polyetheretherketone
(PEEK) moulding and extrusion
materials —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Matériaux à base de polyétheréthercétone (PEEK) pour
moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
Reference number
ISO 23153-2:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 23153-2:2020
ISO 23153-2:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 23153-2:2020
ISO 23153-2:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Preparation of test specimens . 3
4.1 General . 3
4.2 Treatment of material before moulding . 3
4.3 Injection moulding . 3
5 Conditioning of test specimens . 3
6 Determination of properties . 3
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 23153-2:2020
ISO 23153-2:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
A list of all parts in the ISO 23153 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 23153-2:2020
INTERNATIONAL STANDARD ISO 23153-2:2020(E)
Plastics — Polyetheretherk
...
SLOVENSKI STANDARD
oSIST prEN ISO 23153-2:2019
01-april-2019
Polimerni materiali - Materiali na osnovi polietereterketona (PEEK) za oblikovanje
in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO/DIS
23153-2:2019)
Plastics - Polyetheretherketone (PEEK) moulding and extrusion materials - Part 2:
Preparation of test specimens and determination of properties (ISO/DIS 23153-2:2019)
Kunststoffe - Polyetheretherketone (PEEK)-Werkstoffe - Teil 2: Herstellung von
Probekörpern und Bestimmung der Eigenschaften (ISO/DIS 23153-2:2019)
Plastiques - Matériaux à base de polyétheréthercétone (PEEK) pour moulage et
extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés
(ISO/DIS 23153-2:2019)
Ta slovenski standard je istoveten z: prEN ISO 23153-2
ICS:
83.080.20 Plastomeri Thermoplastic materials
oSIST prEN ISO 23153-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 23153-2:2019
---------------------- Page: 2 ----------------------
oSIST prEN ISO 23153-2:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 23153-2
ISO/TC 61/SC 9 Secretariat: KATS
Voting begins on: Voting terminates on:
2019-01-21 2019-04-15
Plastics — Polyetheretherketone (PEEK) moulding and
extrusion materials —
Part 2:
Preparation of test specimens and determination of
properties
Plastiques — Polyétheréthercétone (PEEK) pour moulage et extrusion —
Partie 2: Partie 2: Préparation des éprouvettes et détermination des propriétés
ICS: 83.080.20
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 23153-2:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
oSIST prEN ISO 23153-2:2019
ISO/DIS 23153-2:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 23153-2:2019
ISO/DIS 23153-2:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Preparation of test specimens . 3
4.1 General . 3
4.2 Treatment of material before moulding . 3
4.3 Injection moulding . 3
5 Conditioning of test specimens . 3
6 Determination of properties . 3
© ISO 2019 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 23153-2:2019
ISO/DIS 23153-2:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www .iso .org/iso/foreword .html.
The committee responsible for this document is Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 9, Thermoplastic materials.
A list of all parts in the ISO 23153- series can be found on the ISO website.
iv © ISO 2019 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 23153-2:2019
DRAFT INTERNATIONAL STANDARD ISO/DIS 23153-2:2019(E)
Plastics — Polyetheretherketone (PEEK) moulding and
extrusion materials —
Part 2:
Preparation of test specimens and determination of
properties
1 Scope
This document specifies the methods of preparation of test specimens and the test methods to be used
in determining the properties of polyetheretherketone (PEEK) moulding and extrusion materials.
Requirements for handling test material and for conditioning both the test material before moulding
and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties
of the materials from which these specimens are made are also given. Properties and test methods that
are suitable and necessary to characterize PEEK moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for or of particular significance to these moulding and extrusion materials are also included in
this document, as are the designatory properties specified in ISO 23153-1.
In order to obtain reproducible and comparable test results, it is necessary to use the methods of
preparation and conditioning, the specimen dimensions and the test procedures specified herein.
Values determined will not necessarily be identical to those obtained using specimens of different
dimensions or prepared using different procedures.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any ame
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.