Radio-frequency connectors - Part 59: Sectional specification for type L32-4 and L32-5 threaded muti-pin radio-frequency connectors (IEC 61169-59:2017)

This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for type L32-4 and L32-5 threaded multi-pin
radio frequency connectors with anti mismating mechanism, 50 Ω nominal impedance. The
operating frequency of each channel is up to 4 GHz. These connectors have been widely used
in mobile communication system like TD-SCDMA and TD-LTE, and can also be used in some
similar equipment.
It also prescribes mating face dimensions for general connectors-grade 2, gauging information
and tests selected from IEC 61169-1, applicable to all detail specifications relating to type
L32-4 and L32-5 multi-pin connectors.
This sectional specification provides information and rules for the preparation of detail
specifications for type L32-4 and L32-5 multi-pin connectors together with the pro forma blank
detail specification.
This specification indicates the recommended performance characteristics to be considered
when writing a detail specification and it covers test schedules and inspection requirements
for assessment levels M and H.
NOTE Metric dimension are original dimensions.
All undimensioned pictorial configurations are for reference purpose only.

Hochfrequenzsteckverbinder - Teil 59: Rahmenspezifikation für mehrpolige Hochfrequenzsteckverbinder mit Gewinde Typ L32-4 und L32-5

Connecteurs pour fréquences radioélectriques - Partie 59 : Spécification intermédiaire relative aux connecteurs pour fréquences radioélectriques multibroches filetés de type L32-4 et L32-5

l’IEC 61169-59:2017, qui est une spécification intermédiaire (SS), fournit des informations et des règles pour l'établissement de spécifications particulières (DS) relatives aux connecteurs pour fréquences radioélectriques multibroches filetés de type L32-4 et L32-5 disposant d’un mécanisme de protection contre les erreurs d’accouplement et présentant une impédance nominale de 50 Ω. La fréquence de fonctionnement de chaque canal s’étend jusqu’à 4 GHz. Ces connecteurs sont couramment utilisés au sein de systèmes de communication mobile tels que TD-SCDMA et TD-LTE, et peuvent également être utilisés dans d’autres matériels similaires.
La présente spécification intermédiaire prescrit également les dimensions de la face d’accouplement pour les connecteurs à usage général de grade 2, les informations relatives au calibre et les essais choisis à partir de l’IEC 61169-1, applicables à toutes les spécifications particulières relatives aux connecteurs multibroches de type L32-4 et L32-5.
La présente spécification intermédiaire fournit les informations et les règles destinées à l'établissement de spécifications particulières pour les connecteurs multibroches de type L32-4 et L32-5 ainsi que la spécification particulière-cadre pro forma.
Cette spécification indique les caractéristiques de performance recommandées à prendre en compte lors de l’écriture d’une spécification particulière et elle couvre les programmes d’essai et les exigences de contrôle pour les niveaux d’assurance M et H.

Radiofrekvenčni konektorji - 59. del: Področna specifikacija za navojne večpolne radiofrekvenčne konektorje vrste L32-4 in L32-5 (IEC 61169-59:2017)

Ta del standarda IEC 61169, ki je področna specifikacija (SS), podaja informacije in določa pravila za pripravo podrobnih specifikacij (DS) za radiofrekvenčne konektorje tipa L32-4 in L32-5 z navojem in več nožicami, mehanizmom za preprečevanje nepravilnega stikanja ter nazivno impedanco 50 Ω. Frekvenčno območje delovanja vsakega kanala je do 4 GHz. Ti konektorji so se uporabljali v sistemih za mobilno komunikacijo, kot sta TD-SCDMA in TD-LTE, in se lahko uporabljajo v nekateri podobni opremi.
Določa tudi prednje mere stikanja za splošne konektorje razreda 2, informacije o merjenju in preskuse, izbrane iz standarda IEC 61169-1, ki se uporabljajo za vse podrobne specifikacije v zvezi s konektorji tipa L32-4 in L32-5 z več nožicami.
Ta področna specifikacija podaja informacije in določa pravila za pripravo podrobnih specifikacij za konektorje tipa L32-4 in L32-5 z več nožicami skupaj s pro forma okvirno podrobno specifikacijo.
Ta specifikacija navaja priporočene lastnosti, ki jih je treba upoštevati pri sestavljanju podrobne specifikacije, ter zajema razporede preskusov in zahteve za pregled za ravni vrednotenja M in H.
OPOMBA: Izvirne mere so podane v metričnih merah.
Vse nedimenzionirane slikovne konfiguracije so podane samo v referenčne namene.

General Information

Status
Published
Publication Date
07-Nov-2017
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
27-Sep-2017
Due Date
02-Dec-2017
Completion Date
08-Nov-2017

Buy Standard

Standard
EN 61169-59:2018 - BARVE
English language
35 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61169-59:2018
01-januar-2018
5DGLRIUHNYHQþQLNRQHNWRUMLGHO3RGURþQDVSHFLILNDFLMD]DQDYRMQHYHþSROQH
UDGLRIUHNYHQþQHNRQHNWRUMHYUVWH/LQ/ ,(&
Radio-frequency connectors - Part 59: Sectional specification for type L32-4 and L32-5
threaded muti-pin radio-frequency connectors (IEC 61169-59:2017)
Ta slovenski standard je istoveten z: EN 61169-59:2017
ICS:
33.120.30 5DGLRIUHNYHQþQLNRQHNWRUML RF connectors
5)
SIST EN 61169-59:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61169-59:2018

---------------------- Page: 2 ----------------------

SIST EN 61169-59:2018


EUROPEAN STANDARD EN 61169-59

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2017
ICS 33.120.30

English Version
Radio-frequency connectors -Part 59: Sectional specification for
type L32-4 and L32-5 threaded multi-pin radio-frequency
connectors
(IEC 61169-59:2017)
Connecteurs pour fréquences radioélectriques Partie 59: Hochfrequenzsteckverbinder - Teil 59: Rahmenspezifikation
Spécification intermédiaire relative aux connecteurs pour für mehrpolige Hochfrequenzsteckverbinder mit Gewinde
fréquences radioélectriques multicoaxiaux filetés L32-4 and Typ L32-4 und L32-5
L32-5 (IEC 61169-59:2017)
(IEC 61169-59:2017)
This European Standard was approved by CENELEC on 2017-06-26. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 61169-59:2017 E

---------------------- Page: 3 ----------------------

SIST EN 61169-59:2018
EN 61159-59:2017
European foreword
The text of document 46F/351/CDV, future edition 1 of IEC 61159-59, prepared by SC 46F "RF and
microwave passive components", of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 61159-59:2017.
The following dates are fixed:
• latest date by which the document has to be implemented at (dop) 2018-03-26
national level by publication of an identical national
standard or by endorsement
(dow) 2020-06-26
• latest date by which the national standards conflicting with
the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61159-59:2017 was approved by CENELEC as a European
Standard without any modification.
2

---------------------- Page: 4 ----------------------

SIST EN 61169-59:2018
EN 61159-59:2017

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 2013 Radio-frequency connectors -- Part 1: EN 61169-1 2013
Generic specification - General
requirements and measuring methods
IEC 61726 -  Cable assemblies, cables, connectors and EN 61726 -
passive microwave components -
Screening attenuation measurement by the
reverberation chamber method
IEC 62037 series Passive RF and microwave devices, EN 62037 series
intermodulation level measurement

3

---------------------- Page: 5 ----------------------

SIST EN 61169-59:2018

---------------------- Page: 6 ----------------------

SIST EN 61169-59:2018




IEC 61169-59

®


Edition 1.0 2017-05




INTERNATIONAL



STANDARD








colour

inside










Radio-frequency connectors –

Part 59: Sectional specification for type L32-4 and L32-5 threaded multi-pin

radio-frequency connectors


























INTERNATIONAL

ELECTROTECHNICAL


COMMISSION





ICS 33.120.30 ISBN 978-2-8322-4398-5



  Warning! Make sure that you obtained this publication from an authorized distributor.


® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 7 ----------------------

SIST EN 61169-59:2018
– 2 – IEC 61169-59:2017  IEC 2017
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Mating face and gauge information . 7
4.1 Dimensions – General connectors – Grade 2 . 7
4.1.1 Connector with pin contact . 7
4.1.2 Connector with socket contact . 9
4.1.3 Mating face of RF channel . 12
4.2 Gauges . 13
4.2.1 Gauge for socket centre contact . 13
4.2.2 Gauge for type L32-5 connector with 5 pin contacts . 14
4.2.3 Gauge for L32-4 connector with 4 pin contacts . 15
4.2.4 Gauge for L32-5 connector with 5 socket contacts . 16
4.2.5 Gauge for L32-4 connector with 4 socket contacts . 17
5 Quality assessment procedure . 19
5.1 General . 19
5.2 Rating and characteristics . 19
5.3 Test schedule and inspection requirements. 21
5.3.1 Acceptance tests . 21
5.3.2 Periodic tests . 22
5.4 Procedures for the qualification approval . 24
5.4.1 Quality conformance inspection . 24
5.4.2 Qualification approval and its maintenance . 24
5.4.3 Periodic tests . 24
5.4.4 Procedures for quality conformance . 24
6 Instructions for preparation of detail specifications . 25
6.1 General . 25
6.2 Identification of the component . 25
6.3 Performance . 25
6.4 Marking, ordering information and related matters . 25
6.5 Selection of tests, test conditions and severities . 25
6.6 Blank detail specification pro-forma for Type L32-4 and L32-5 threaded
multi-pin radio frequency connectors . 26
7 Marking . 31
7.1 Marking of component . 31
7.2 Marking and contents of package . 31
Annex A (normative) Isolation test method . 32
A.1 Preparation of test sample . 32
A.2 Test procedure . 32

Figure 1 – L32-5 connector with 5 pin contacts . 7
Figure 2 – L32-4 connector with 4 pin contacts . 8
Figure 3 – L32-5 connector with 5 socket contacts . 9
Figure 4 – L32-4 connector with 4 socket contacts . 11
Figure 5 – Mating face of RF channel . 12

---------------------- Page: 8 ----------------------

SIST EN 61169-59:2018
IEC 61169-59:2017  IEC 2017 – 3 –
Figure 6 – Gauge for socket contact of RF channel . 13
Figure 7 – Gauge for L32-5 connector with 5 pin contacts . 14
Figure 8 – Gauge for L32-4 connector with 4 pin contacts . 15
Figure 9 – Gauge for L32-5 connector with 5 socket contacts . 16
Figure 10 – Gauge for L32-4 connector with 4 socket contacts . 18

Table 1 – Dimensions of L32-5 connector with 5 pin contacts . 8
Table 2 – Dimensions of L32-4 connector with 4 pin contacts . 9
Table 3 – Dimensions of L32-5 connector with 5 socket contacts . 10
Table 4 – Dimensions of L32-4 connector with 4 socket contacts . 11
Table 5 – Dimensions of the mating face of RF channel . 13
Table 6 – Dimensions of gauge for socket contact . 14
Table 7 – Dimensions of gauge L32-5 connector with 5 pin contacts . 15
Table 8 – Dimensions of gauge L32-4 connector with 4 pin contacts . 16
Table 9 – Dimensions of gauge for L32-5 connector with 5 socket contacts . 17
Table 10 – Dimensions of gauge for L32-4 connector with 4 socket contacts . 18
Table 11 – Rating and characteristics . 20
Table 12 – Acceptance tests . 22
Table 13 – Periodic tests . 23

---------------------- Page: 9 ----------------------

SIST EN 61169-59:2018
– 4 – IEC 61169-59:2017  IEC 2017
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

RADIO-FREQUENCY CONNECTORS –

Part 59: Sectional specification for type L32-4 and L32-5
threaded multi-pin radio-frequency connectors

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61169-59 has been prepared by subcommittee 46F: RF and
microwave passive components, of IEC technical committee 46: Cables, wires, waveguides,
RF connectors, RF and microwave passive components and accessories.
The text of this International Standard is based on the following documents:
CDV Report on voting
46F/351/CDV 46F/362/RVC

Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.

---------------------- Page: 10 ----------------------

SIST EN 61169-59:2018
IEC 61169-59:2017  IEC 2017 – 5 –
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

A bilingual version of this publication may be issued at a later date.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.

---------------------- Page: 11 ----------------------

SIST EN 61169-59:2018
– 6 – IEC 61169-59:2017  IEC 2017
RADIO-FREQUENCY CONNECTORS –

Part 59: Sectional specification for type L32-4 and L32-5
threaded multi-pin radio-frequency connectors



1 Scope
This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for type L32-4 and L32-5 threaded multi-pin
radio frequency connectors with anti mismating mechanism, 50 Ω nominal impedance. The
operating frequency of each channel is up to 4 GHz. These connectors have been widely used
in mobile communication system like TD-SCDMA and TD-LTE, and can also be used in some
similar equipment.
It also prescribes mating face dimensions for general connectors-grade 2, gauging information
and tests selected from IEC 61169-1, applicable to all detail specifications relating to type
L32-4 and L32-5 multi-pin connectors.
This sectional specification provides information and rules for the preparation of detail
specifications for type L32-4 and L32-5 multi-pin connectors together with the pro forma blank
detail specification.
This specification indicates the recommended performance characteristics to be considered
when writing a detail specification and it covers test schedules and inspection requirements
for assessment levels M and H.
NOTE Metric dimension are original dimensions.
All undimensioned pictorial configurations are for reference purpose only.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 61169-1:2013, Radio frequency connectors – Part 1: Generic specification – General
requirements and measuring methods
IEC 61726, Cable assemblies, cables, connectors and passive microwave components –
Screening attenuation measurement by the reverberation chamber method
IEC 62037 (all parts), Passive RF and microwave devices, intermodulation level measurement
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:

---------------------- Page: 12 ----------------------

SIST EN 61169-59:2018
IEC 61169-59:2017  IEC 2017 – 7 –
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
4 Mating face and gauge information
4.1 Dimensions – General connectors – Grade 2
4.1.1 Connector with pin contact
4.1.1.1 L32-5 connector with 5 pin contacts
The mating face of L32-5 connector with 5 pin contacts is shown in Figure 1 and its
dimensions are shown in Table 1.

B
Main groove
36°
Note6
C
144° 1
108°
5Pin EQS

0.1 A B C
Note5
180°
2Supplementary groove
Note3
Note2
Note1
Note4
A
216°
IEC

NOTE 1 Mechanical and electrical reference plane.
NOTE 2 Chamfer of three grooves is optional.
NOTE 3 The mating face of RF channel with pin contact is shown in Figure 5a) in 4.1.3 and its dimensions are
shown in Table 5.
NOTE 4 The shape of seal ring is optional.
NOTE 5 Anti-mismating pin.
NOTE 6 The initial position number of RF channel with pin contact and the other positions numbered clockwise.
Figure 1 – L32-5 connector with 5 pin contacts

---------------------- Page: 13 ----------------------

SIST EN 61169-59:2018
– 8 – IEC 61169-59:2017  IEC 2017
Table 1 – Dimensions of L32-5 connector with 5 pin contacts
Ref. mm
Min. Max.
a 6,0 6,1
b 6,0 6,2
c 7,5 7,6
d M32X1,5-6g
e 14,4 14,5
f 6,0 –
g 9,5 9,7
h 24,0 –
k 27,0 27,1
m 2,1 2,2
n 16,5

4.1.1.2 L32-4 connector with 4 pin contacts
The mating face of L32-4 connector with 4 pin contacts is shown in Figure 2 and its
dimensions are shown in Table 2.
D
D-D

B
Main groove
Note6
36°
Note5
D
D
144°
1
C
108°
D
D
5Pin EQS

0.1
A B C
180°
Supplementary groove
Note3
Note2
Note4
Note1
216°
A
D
IEC

NOTE 1 Mechanical and electrical reference plane.
NOTE 2 Chamfer of three grooves is optional.
NOTE 3 The mating face of RF channel with pin contact is shown in Figure 5a) in 4.1.3 and its dimensions are
shown in Table 5.
NOTE 4 The shape of seal ring is optional.
NOTE 5 Anti-mismating pin.
NOTE 6 The initial position number of RF channel with pin contact and the other positions numbered clockwise.
Figure 2 – L32-4 connector with 4 pin contacts

---------------------- Page: 14 ----------------------

SIST EN 61169-59:2018
IEC 61169-59:2017  IEC 2017 – 9 –
Table 2 – Dimensions of L32-4 connector with 4 pin contacts
Ref. mm
Min. Max.
a 6,0 6,1
b 6,0 6,2
c 7,5 7,6
d M32X1,5-6g
e 14,4 14,5
f 6,0 --
g 9,5 9,7
h 24,0 --
k 27,0 27,1
m 2,1 2,2
n 16,5
16,52

4.1.2 Connector with socket contact
4.1.2.1 L32-5 connector with 5 socket contacts
The mating face of L32-5 connector with 5 socket contacts is shown in Figure 3 and its
dimensions are shown in Table 3.

B
Main key
Note5 36°
Note4
1
144°
108°
C
5Socket EQS

0.1 A B C
Note2
2Supplementary key
180°
Note3
Note1
A
216°
IEC

NOTE 1 Mechanical and electrical reference plane.
NOTE 2 The mating face of RF channel with socket contact is shown in Figure 5b) in 4.1.3 and its dimensions are
shown in Table 5.
NOTE 3 Anti-mismating socket.
NOTE 4 The shape of key of shell is optional.
NOTE 5 The initial position number of RF channel with socket contact and the other positions numbered anti-
clockwise.
Figure 3 – L32-5 connector with 5 socket contacts

---------------------- Page: 15 ----------------------

SIST EN 61169-59:2018
– 10 – IEC 61169-59:2017  IEC 2017
Table 3 – Dimensions of L32-5 connector with 5 socket contacts
Ref. mm
Min. Max.
a 6,25 6,35
b 7,0 --
c 7,7 7,8
d M32X1,5-7H
e 14,2 14,3
f 7,6 8,0
g -- 0,8
h 6,8 --
i 0,08 0,3
j 11,5 11,7
k 26,6 26,7
l 34,9 35,0
m 1,9 2,0
n 16,5
16,52
p 5,8 6,1

4.1.2.2 L32-4 connector with 4 socket contacts
The mating face of L32-4 connector with 4 socket contacts is shown in Figure 4 and its
dimensions are shown in Table 4.

---------------------- Page: 16 ----------------------

SIST EN 61169-59:2018
IEC 61169-59:2017  IEC 2017 – 11 –
D
D-D

B
Main key
Note3
36°
Note4
Note5
D
D
1
144°
C
108°
D
D
5Socket EQS
180°

0.1 A B C
Note2
2Supplementary key
Note1
216°
A

D
IEC
NOTE 1 Mechanical and electrical reference plane.
NOTE 2 The mating face of RF channel with socket contact is shown in Figure 5b) in 4.1.3 and its dimensions are
shown in Table 5.
NOTE 3 Anti-mismating socket.
NOTE 4 The shape of key of shell is optional.
NOTE 5 The initial position number of RF channel with socket contact and the other positions numbered anti-
clockwise.
Figure 4 – L32-4 connector with 4 socket contacts
Table 4 – Dimensions of L32-4 connector with 4 socket contacts
Ref. mm
Min. Max.
a 6,25 6,35

b 7,0 –
c 7,7 7,8
d M32X1,5-7H
e 14,2 14,3
f 7,6 8,0
g – 0,8
h 6,8 –
i 0,08 0,3
j 11,5 11,7
k 26,6 26,7
l 34,9 35,0
m 1,9 2,0
n 16,5 16,52
p 5,8 6,1

---------------------- Page: 17 ----------------------

SIST EN 61169-59:2018
– 12 – IEC 61169-59:2017  IEC 2017
4.1.3 Mating face of RF channel
The mating face of RF channel with pin contact is shown in Figure 5a), the mating face of RF
channel with socket contact is shown in Figure 5b), their dimensions are shown as Table 5.
Note1

60°

IEC

a) RF channel with pin contact
Note1
Detail A
Note2
Detail A
IEC

b) RF channel with socket contact
NOTE 1 Mechanical and electrical reference plane.
NOTE 2 The position of floating outer conductor in free state and its slot design is optional.
Figure 5 – Mating face of RF channel

---------------------- Page: 18 ----------------------

SIST EN 61169-59:2018
IEC 61169-59:2017  IEC 2017 – 13 –
Table 5 – Dimensions of the mating face of RF channel
Ref. mm
Min. Max.
a 0,00 0,25
b 0,00 0,25
c 1,27 –
d – 2,54
f 0,902 0,935
g 0,00 0,10
h 0,00 0,25
i 0,08 0,30
j 2,67 –
k 0,00 0,25
a
– –
l
b
– –
m
c
0,3 –
n
a It is assumed that the mechanical and electrical requirements are met with the chosen dimension for pin
Φ0,902 mm to Φ0,935 mm,
b Slot design is optional, as soon as it meets the mechanical and electrical requirements.
c 0,2 mm to 0,3 mm of radial displacement is allowed when mating of RF channel with pin contact.

4.2 Gauges
4.2.1 Gauge for socket centre contact
The gauge for socket contact of RF channel is shown in Figure 6 and its dimensions are
shown in Table 6.
IEC

Figure 6 – Gauge for socket contact of RF channel

---------------------- Page: 19 ----------------------

SIST EN 61169-59:2018
– 14 – IEC 61169-59:2017  IEC 2017
Table 6 – Dimensions of gauge for socket contact
Ref. Gauge A Gauge B Gauge C
(For sizing purpose) (For insertion purpose)
(For retention purpose)
+2
Mass of gauge:28 g
0
mm mm mm
Min. Max. Min. Max. Min. Max.
a 0,950 0,955 0,935 0,940 0,899 0,902
b 0,76 1,14 1,27 1,91 1,27 1,91
Material: steel, polished. Surface roughness: Ra ≤0,4 μm.

Test procedure:
a) Sizing test
The gauge A should insert the socket centre contact of RF channel three times; this is a
sizing operation.
b) Insertion test
Following the sizing operation, if specified in the detail specification, the force necessary
to insert Gauge B fully into the socket centre contact shall be measured. When this test is
required, the insertion force shall not exceed 8,9 N.
c) Retention test
After sizing or insertion test, the gauge C shall be inserted into the socket centre contact.
The contact shall retain the mass of the gauge C in a vertical downward position.
4.2.2 Gauge for type L32-5 connector with 5 pin contacts
The gauge for type L32-5 connector with 5 pin contacts is shown in Figure 7 and its
dimensions are shown in Table 7.

B
Main key
Note2 36°
Detail A
144°
C
108°
5Socket EQS

0.08 A B C
180°
Note1
2Supplementary key
A
Detail A
216°
IEC

NOTE 1 Mechanical and electrical reference plane.
NOTE 2 Anti-mismating socket.
Figure 7 – Gauge for L32-5 connector with 5 pin contacts

---------------------- Page: 20 ----------------------

SIST EN 61169-59:2018
IEC 61169-59:2017  IEC 2017 – 15 –
Table 7 – Dimensions of gauge L32-5 connector with 5 pin contacts
Ref. mm
Min. Max.
a 6,25 6,35
b 7,0 –
c 0,935 0,940
d 2,67 –
e 14,4 14,5
g – 0,8
k 26,65 26,70
m 1,95 2,00
n 16,48 16,52

Test procedure:
Mechanical compatibility test: The gauge should insert the L32-5 connector with 5 pin
contacts three times, and then measure the insertion force; the insertion force should be not
less than 50 N.
4.2.3 Gauge for L32-4 connector with 4 pin contacts
The gauge for L32-4 connector with 4 pin contacts is shown in Figure 8 and its dimensions
are shown in Table 8.
E
E-E
B
Main key
36°
Note2
Detail D
E
E
C
144°
108°
E
E
5Socket EQS

0.08 A B C
180°
2Supplementary key
Note1
Detail D
A
216°
E
IEC

NOTE 1 Mechanical and electrical reference plane.
NOTE 2 Anti-mis
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.