SIST EN ISO 25649-3:2017
(Main)Floating leisure articles for use on and in the water - Part 3: Additional specific safety requirements andtest methods for Class A devices (ISO 25649-3:2017)
Floating leisure articles for use on and in the water - Part 3: Additional specific safety requirements andtest methods for Class A devices (ISO 25649-3:2017)
This European Standard is applicable for CLASS A classified floating leisure articles for use on and in water according to EN 15649-1 regardless whether the buoyancy is achieved by inflation or inherent buoyant material.
This document (EN 15649-3) is applicable with EN 15649-1 and EN 15649-2.
Schwimmende Freizeitartikel zum Gebrauch auf und im Wasser - Teil 3: Zusätzliche besondere sicherheitstechnische Anforderungen und Prüfverfahren für Artikel der Klasse A (ISO 25649-3:2017)
Articles de loisirs flottants à utiliser sur ou dans l'eau - Partie 3 : Exigences de sécurité et méthodes d'essai complémentaires propres aux dispositifs de Classe A (ISO 25649-3:2017)
ISO 25649-3:2017 est applicable aux articles de loisirs flottants de Classe A à utiliser sur ou dans l'eau conformément à l'ISO 25649‑1, dont la flottabilité est assurée par gonflage ou par un matériau ayant une flottabilité propre.
ISO 25649-3:2017 s'applique conjointement à l'ISO 25649‑1 et à l'ISO 25649‑2.
NOTE 1 Produits typiques constituant la Classe A (voir l'Annexe A):
- «îles flottantes» de forme presque ronde ou carrée, décorées avec un palmier, une protection solaire, etc.; superstructure haute;
- grands flotteurs/radeaux de formes variées, rondes à carrées;
- grands tubes flottants («float tubes»), tubes géants (gonflables ou ayant une flottabilité propre);
- fauteuils, sièges et transats flottants;
- matelas pneumatiques à utiliser sur l'eau;
- radeaux de loisirs/plates-formes flottantes/pontons.
NOTE 2 Lieux d'utilisation typiques:
- piscines;
- zones protégées des lacs, étangs;
- zone protégée en bord de mer (pas de vent de terre, ni de courant).
Plavajoči pripomočki za prosti čas, ki se uporabljajo na vodi in v njej - 3. del: Dodatne posebne varnostne zahteve in preskusne metode za pripomočke razreda A (ISO 25649-3:2017)
Ta evropski standard se uporablja za plavajoče pripomočke za prosti čas, razvrščene v RAZRED A, ki se uporabljajo na vodi in v njej v skladu s standardom EN 15649-1, ne glede na to, ali je plovnost dosežena z napihovanjem ali plovnim materialom. Ta dokument (EN 15649-3) se uporablja s standardoma EN 15649-1 in EN 15649-2.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 25649-3:2017
01-december-2017
1DGRPHãþD
SIST EN 15649-3:2010+A1:2012
3ODYDMRþLSULSRPRþNL]DSURVWLþDVNLVHXSRUDEOMDMRQDYRGLLQYQMHMGHO
'RGDWQHSRVHEQHYDUQRVWQH]DKWHYHLQSUHVNXVQHPHWRGH]DSULSRPRþNHUD]UHGD
$ ,62
Floating leisure articles for use on and in the water - Part 3: Additional specific safety
requirements andtest methods for Class A devices (ISO 25649-3:2017)
Schwimmende Freizeitartikel zum Gebrauch auf und im Wasser - Teil 3: Zusätzliche
besondere sicherheitstechnische Anforderungen und Prüfverfahren für Artikel der Klasse
A (ISO 25649-3:2017)
Articles de loisirs flottants à utiliser sur ou dans l'eau - Partie 3 : Exigences de sécurité et
méthodes d'essai complémentaires propres aux dispositifs de Classe A (ISO 25649-
3:2017)
Ta slovenski standard je istoveten z: EN ISO 25649-3:2017
ICS:
97.220.40 Oprema za športe na Outdoor and water sports
prostem in vodne športe equipment
SIST EN ISO 25649-3:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 25649-3:2017
---------------------- Page: 2 ----------------------
SIST EN ISO 25649-3:2017
EN ISO 25649-3
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2017
EUROPÄISCHE NORM
ICS 97.220.40 Supersedes EN 15649-3:2009+A1:2012
English Version
Floating leisure articles for use on and in the water - Part
3: Additional specific safety requirements and test
methods for Class A devices (ISO 25649-3:2017)
Articles de loisirs flottants à utiliser sur ou dans l'eau - Schwimmende Freizeitartikel zum Gebrauch auf und
Partie 3: Exigences de sécurité et méthodes d'essai im Wasser - Teil 3: Zusätzliche besondere
complémentaire propre aux dispositifs de Classe A (ISO sicherheitstechnische Anforderungen und
25649-3:2017) Prüfverfahren für Artikel der Klasse A (ISO 25649-
3:2017)
This European Standard was approved by CEN on 24 June 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25649-3:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 25649-3:2017
EN ISO 25649-3:2017 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 25649-3:2017
EN ISO 25649-3:2017 (E)
European foreword
This document (EN ISO 25649-3:2017) has been prepared by Technical Committee ISO/TC 83 “Sports
and other recreational facilities and equipment” in collaboration with Technical Committee
CEN/TC 136 “Sports, playground and other recreational facilities and equipment” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2018, and conflicting national standards shall be
withdrawn at the latest by April 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15649-3:2009+A1:2012.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 25649-3:2017 has been approved by CEN as EN ISO 25649-3:2017 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 25649-3:2017
---------------------- Page: 6 ----------------------
SIST EN ISO 25649-3:2017
INTERNATIONAL ISO
STANDARD 25649-3
First edition
2017-08
Floating leisure articles for use on and
in the water —
Part 3:
Additional specific safety
requirements and test methods for
Class A devices
Articles de loisirs flottants à utiliser sur ou dans l'eau —
Partie 3: Exigences de sécurité et méthodes d'essai complémentaire
propre aux dispositifs de Classe A
Reference number
ISO 25649-3:2017(E)
©
ISO 2017
---------------------- Page: 7 ----------------------
SIST EN ISO 25649-3:2017
ISO 25649-3:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 25649-3:2017
ISO 25649-3:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Safety requirements and test methods . 2
4.1 General . 2
4.2 Design, sizing, admissible number of users and maximum load capacity . 3
4.2.1 General. 3
4.2.2 Sizing . 3
4.2.3 A1-products, space per person and admissible number of users . 3
4.2.4 A2-products, space per person and admissible number of users . 4
4.3 In water performance . 5
4.3.1 Amount of buoyancy and stable floating position . 5
4.3.2 Residual buoyancy of devices claiming floating stability (CASES A, B) . 6
4.3.3 Residual buoyancy of floating leisure articles not claiming floating
stability (CASES C, D) . 8
4.3.4 Capsizing and escape . 9
4.3.5 Grab handles and safety lines (not applicable to air mattresses) . 9
4.3.6 Re-embarkation from the water in normal use and failure of one air
chamber in CASE A1 .10
4.3.7 Extreme high super structure (wind, drift) .10
4.3.8 Anchorage .10
4.3.9 Giant rings with bottom, strength of entire device .11
5 Consumer information .11
5.1 General .11
5.2 Consumer information on the packaging (point of sale information) .11
5.3 Consumer information on the product (information related to safe use) .12
5.4 Consumer information by instructions for use (separate written information) .12
5.4.1 General.12
5.4.2 Safety and product information .12
5.4.3 Assembly (if applicable) .12
5.4.4 Maintenance and repair (if applicable) .12
6 Test report .12
7 Exclusions .12
Annex A (informative) Examples of typical products forming Class A .13
Bibliography .15
© ISO 2017 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 25649-3:2017
ISO 25649-3:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
ISO 25649-3 was prepared by the European Committee Standardization (CEN) Technical Committee
CEN/TC 136, Sports, playground and other recreational facilities and equipment, in collaboration with ISO
Technical Committee TC 83, Sports and other recreational facilities and equipment, in accordance with
the agreement on technical cooperation between ISO and CEN (Vienna Agreement).
A list of all the parts in the ISO 25649-series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 25649-3:2017
ISO 25649-3:2017(E)
Introduction
According to the nature and the intended use of the products dealt with in this document the technical
requirements are focused on space per person, floating stability matters and residual buoyancy in case
of an emergency.
It needs to be taken into account that some of the products provide dual or multiple use features.
Comprehensive consumer information requirements complete the requirement profile of the document
and include basic purchase information on whether a product provides floating stability or needs to be
balanced by the user.
Risk assessment for this document is shown in Table 1.
© ISO 2017 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 25649-3:2017
ISO 25649-3:2017(E)
Table 1 — Introductory risk analysis
1.1 Pro-
Position
tection
Function; of user
Partial risk
aims;
range of Type of regarding
Typical Place of Predictable related to
Class usage; movement / equipment Final risk
1.2 Relat-
products usage misuse water envi-
target/age propulsion and eleva-
ed stand-
ronment
group tion above
ard/reg-
water
ulation
Floating in- Sea shore, R e l a x i n g , Static use On or in (side Dangerous dis- U n no t ic e d F l oa t i ng
flatable is- close to resting on within limit- walls) the de- tance from the drifting to stabilit y;
lands; recre- shore; lakes; the water; ed area; little vice, laying, bank/ shore; open wa - minimum
ational raft; s m o o t h ly sunbat hing; action; move- sitting, no di- use in cur- ters; falling buoyancy;
p l a t f or m/ r u nni n g basis for ment by push- rect body fit; rents and/ asleep and r esi d u a l
pontoon, etc. rivers; pub- bathing and ing through or danger- consequent- buoy a n -
grab handles
lic/ private s w im m in g/ s w i m m i n g ous offshore l y e x t r e m e cy; space,
might exist but
pools; ponds playing; device strokes only; winds; use sunburn, etc.; safety han-
resting does
providing high by non-swim- capsizing; skin dles/lines;
no mechanical not depend
level of float- mers; fall over irritation due anchorage;
means of pro- on gripping/
ing stability; board; no div- to long dura- w a r n i n g
pulsion balancing;
A1 single and ing platform! tion of skin notes, la-
collective use; c o nt ac t / b e l l i ng ,
no dangerous
all age groups, d a n g e r o u s swimmers
height of fall
swimmers substances in only, age
contact with r e s t r ic -
skin; climbing tion ac -
back?; hypo- cording to
thermia; cold ISO 6185-1,
shock ISO 6185-2
a n d
ISO 6185-3
Large buoy- Sea shore/ Action, playing Drifting; pro- On the device; U s e b y Drifting away Labelling,
ant struc- close to in the water; pulsion only loose fit via non- s w i m - in open waters r esi d u a l
tures shore, lakes, b a l a n c i n g by swimming handles; no mers; use In due to wind DROWN- buoyancy,
public/ pri- children; col- strokes or d a n g e r o u s current, canal, and/or cur- ING grab han-
vate pools; lective and third party height lack of super- rent; devices dles, su-
ponds single use; all vision provokes use pervision;
age groups, in deep; used warnings
A2
swimmers by non-swim-
mers; falling
into deep
water
Air mat - Sea shore Resting on Normally no On/in the de- See A1/A2 See A1/A2 See A1/A2
tress for close to the the water; ob- me c h a n ic a l vice; device is
No rule is
use in water; shore; lakes, servation of means of pro- clung on; de-
known to
f lo a t a b l e public/ pri- under water pulsion but vice is held;
pr o v ide
pool loung- vate pools; environment; possible; drift- mainly a near
technical
ers; f loat- ponds sea play; mainly ing or propul- h o r i z o n t a l
substance
ing seating single use; sion by swim- posture sit-
structures; floating stabil- ming strokes; ting;
A1/A2
giant rings/ ity depends on seats might be
no relevant el-
tubes design; equipped with
evation above
pedals (wheel
all age groups, water level
propulsion)
swimmers
vi © ISO 2017 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 25649-3:2017
INTERNATIONAL STANDARD ISO 25649-3:2017(E)
Floating leisure articles for use on and in the water —
Part 3:
Additional specific safety requirements and test methods
for Class A devices
1 Scope
This document is applicable for CLASS A classified floating leisure articles for use on and in water
according to ISO 25649-1 regardless whether the buoyancy is achieved by inflation or inherent buoyant
material.
This document is to be applied with ISO 25649-1 and ISO 25649-2.
NOTE 1 Typical products forming Class A (see Annex A):
— “Floating Islands” in near round or square shaped forms decorated with palm tree, sun shade,
etc. high superstructure;
— large floats/rafts in various forms from round to square;
— large floating tubes, giant tubes (inflatable or inherently buoyant);
— floating arm chairs, seats and sun beds;
— air mattresses for use on the water;
— recreational rafts/floating platforms/pontoons.
NOTE 2 Typical places for application:
— pools;
— protected areas of lakes, ponds;
— protected area sea shore (no offshore winds, no currents).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 25649-1:2017, Floating leisure articles for use on and in the water — Part 1: Classification, materials,
general requirements and test methods
ISO 25649-2, Floating leisure articles for use on and in the water — Part 2: Consumer information
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 25649-1 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http://www.iso.org/obp
© ISO 2017 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 25649-3:2017
ISO 25649-3:2017(E)
— IEC Electropedia: available at http://www.electropedia.org/
3.1
residual buoyancy
provision of remaining buoyancy in case of a defect of any buoyancy chamber
3.2
floating stability
no user action required to maintain safe floating
Note 1 to entry: One or several users can be safely on or in the device even if the weight is not evenly distributed.
Note 2 to entry: In accordance with intended use.
3.3
device to be balanced by the user
user action required to create safe floating
Note 1 to entry: In accordance with intended use.
3.4
escape
easy and complete separation between the user and the device in case of capsizing of the device or
system without hindrance through any part or feature of the floating device
3.5
available area
area on or inside a floating article which can be used unrestrictedly for user accommodation when
taking the intended posture(s)
3.6
multiple use product
any product intended to be used for more than one purpose for examples (jumping, resting, climbing, etc.)
3.7
inherent buoyant material
non-crosslinked (closed-cell) foam or other materials enclosed in (a) sealed compartment(s) in the hull
which have a specific weight less than water
Note 1 to entry: Inflatables made from inherent buoyant material are considered a buoyant structure (hull)
achieving all or parts of its intended shape and buoyancy resulting from soft foam, hard foam or sealed chambers
filled with air, gas or granules.
4 Safety requirements and test methods
4.1 General
Construction of a floating leisure article shall be such that it corresponds in terms of design, dimensions,
safety, strength and durability for its intended use. The requirements set out in this standard were
chosen to ensure compliance with these considerations. If inflatable floating leisure articles shall
provide buoyancy in several components then requirements apply to all components. Floating leisure
articles shall provide residual buoyancy if one air chamber fails. This residual buoyancy shall maintain
the safety of the device even if its function is lost. The following safety requirements are therefore
related to:
— design;
— sizing;
— materials;
2 © ISO 2017 – All rights reserved
---------------------- Page: 14 ----------------------
SIST EN ISO 25649-3:2017
ISO 25649-3:2017(E)
— strength;
— performance;
— information.
In individual cases, due to the unpredictability, valency and indeterminability of existing and future
concrete products, a corresponding choice shall be made.
Design and appearance of floating leisure articles shall not change the intended primary function of
these floating leisure articles nor introduce a toy play value.
4.2 Design, sizing, admissible number of users and maximum load capacity
4.2.1 General
Devices shall be marked according to their size and/or number of permitted users and maximum load
capacity.
4.2.2 Sizing
4.2.2.1 Requirements
If a specific size/body weight correlation between user and device is relevant, the marking shall be in
accordance with the range of body weights. The size/body weights of the user shall be indicated on the
product by completing the relevant boxes of the appropriate safety information symbol “User’s body
weight range” as specified in ISO 25649-2.
4.2.2.2 Test method
Check for correct marking and completion.
4.2.3 A1-products, space per person and admissible number of users
4.2.3.1 Requirements
A1-products shall be labelled with regard to the intended posture — lying/sitting — of the user(s)
and the maximum permissible number of users. The minimum space for a user in lying posture shall
correspond to a flexible template (adult/child) the dimensions of which are specified in ISO 25649-1:2017,
A.1.1. The minimum space for a sitting user shall correspond to the template (adult/child) as specified
in ISO 25649-1:2017, A.1.2. In cases of combined use (sitting and lying), the template for a lying person
shall be applied to determine the available area.
Templates may exceed the outer circumference of the device to a total amount of 30 %. This amount is
divided in 15 % of template length for the head area and 15 % of template length for the leg area (see
shaded area of templates in ISO 25649-1:2017, Annex A). The angle between centre line of the template
and tangential of a possible back rest, board wall, etc. shall be greater than 60° (see Figure 1).
The total amount of users determined by the templates shall not contradict to the load capacity and
floating stability of the device.
Space requirement using templates is not applicable for ride-on devices where distinct upright seats
and/or seating positions are imposed by the device.
4.2.3.2 Test method
Testing shall be done by applying the relevant templates as specified in ISO 25649-1:2017, A.1 and shown
in Figure 1. Templates shall be stretched out over the area available to the user without overlapping.
© ISO 2017 – All rights reserved 3
---------------------- Page: 15 ----------------------
SIST EN ISO 25649-3:2017
ISO 25649-3:2017(E)
Templates may be arranged to optimize the amount of users and the mix of adults and children without
contradicting to the load capacity of the device. Blank areas of templates shall be completely inside
the outer circumference. Check by visual inspection for appropriate labelling in accordance with safety
information symbols “Number of users, adult/children” and/or “Maximum load capacity” as specified
in ISO 25649-2.
a) A1, “Big raft”: 3,8 m in diameter/4,8 m × 2,8 m
b) A1, “Small raft”: 2,5 m in diameter/3 m × 2 m
Key
1 template space per person, adult
2 template Space per person, child
Figure 1 — Available space per person, determination of number of users
4.2.4 A2-products, space per person and admissible number of users
4.2.4.1 Requirements
A-2 products shall provide distinct seat(s) or sitting areas or recognizable space where the user is to
be positioned in the intended posture. Seats, etc. of ride-on devices shall be equipped with at least one
grab handle for each permissible user.
If the device implies sitting in line of more than one user, the sitting space for each user shall be at least
a length of:
— Child = 30 cm if the legs hang down;
— Child = 60 cm if the thighs follow the seat surface.
— Adult = 35 cm if the legs hang down;
— Adult = 70 cm if the thighs follow the seat surface.
4.2.4.2 Test method
Visual inspection and measurement.
4 © ISO 2017 – All rights reserved
---------------------- Page: 16 ----------------------
SIST EN ISO 25649-3:2017
ISO 25649-3:2017(E)
4.3 In water performance
4.3.1 Amount of buoyancy and stable floating position
4.3.1.1 Requirements
All devices (A1, A2) shall provide sufficient buoyancy and adequate buoyancy distribution to bear the
weight of the intended number of users. Floating devices shall float stable with all test subjects placed
on the intended position and posture on the device. The design supporting area shall not be flooded, not
applicable if the product is designed to provide a supporting area which is intentionally under water.
Floating leisure articles claiming to provide floating stability (A1) shall additionally meet the test as
specified in 4.3.2.2.2. When loaded with the maximum/minimum number of passengers, the device
shall maintain the stable floating position as defined in ISO 25649-1:2017, 3.13.
The capability of stable floating performance or the need for balancing shall be marked on the
packaging via the relevant pair-safety information symbol “Device provides floating stability” and
“Device requires balancing” as specified in ISO 25649-2.
4.3.1.2 Test method
The maximum number of test subjects according to manufacturer's declaration (adults, children) shall
be placed within the available area with no part of the body outside the product in a way as shown in
Figure 2. If a device is classified for more than one user, the array of all test subjects shall be done by
applying the determined postures and positions in a way most likely to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.