Specification for protective clothing for use where there is a risk of entanglement with moving parts

This standard specifies the properties of protective clothing that minimize the risk of its entanglement or drawing-in by moving parts when the wearer is working at or near hazardous moving machines or devices. This standard does not include protective clothing against injuries by special moving machine parts for which specific standards exist, e.g. protective clothing for users of chainsaws.

Festlegungen für Schutzkleidungen für Bereiche, in denen ein Risiko des Verfangens in beweglichen Teilen besteht

Dieses Dokument legt in Ergänzung zu den allgemeinen Anforderungen in EN ISO 13688 Ausführungsanforderungen an Schutzkleidungsstücke, die das Risiko ihres Verfangens oder Einziehens durch bewegte Teile, wenn der Träger an oder in der Nähe von Maschinen oder Geräten mit gefährlichen Bewegungen arbeitet, minimieren, fest.

Spécification pour l’habillement de protection destiné à être utilisé en cas de risque de happement par des pièces de machines en mouvement

Le présent document spécifie les exigences de conception des vêtements de protection qui réduisent au minimum les risques de happement ou d'entraînement par des pièces en mouvement lorsque le porteur travaille sur ou à proximité des machines ou appareils en mouvement dangereux. Ces exigences sont complémentaires des exigences générales énoncées dans l'EN ISO 13688.
Le présent document exclut l’habillement de protection contre les blessures occasionnées par des parties particulières de machines en mouvement pour lequel il existe des normes spécifiques, par exemple l’habillement de protection pour les utilisateurs de scies à chaîne (EN ISO 11393).

Opredelitev zahtev za varovalno oblačilo, kjer je nevarnost, da se oblačilo zaplete ob gibajoče dele

Ta standard določa lastnosti varovalnih oblačil, pri katerih je nevarnost, da se oblačilo zaplete ob premikajoče se dele oziroma da se vanje zatakne, ko uporabnik dela na nevarnih premičnih strojih ali napravah oziroma v njihovi bližini, kar najmanjša. Ta standard ne vključuje varovalnih oblačil za zaščito pred poškodbami s posebnimi premikajočimi se deli strojev, za katere obstajajo posebni standardi, npr. varovalna oblačila za uporabnike motornih žag.

General Information

Status
Published
Public Enquiry End Date
24-Oct-2018
Publication Date
16-Dec-2019
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
11-Dec-2019
Due Date
15-Feb-2020
Completion Date
17-Dec-2019

RELATIONS

Buy Standard

Standard
SIST EN 510:2020
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Draft
oSIST prEN 510:2018
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 510:2020
01-januar-2020
Nadomešča:
SIST EN 510:1996

Opredelitev zahtev za varovalno oblačilo, kjer je nevarnost, da se oblačilo zaplete

ob gibajoče dele

Specification for protective clothing for use where there is a risk of entanglement with

moving parts

Festlegungen für Schutzkleidungen für Bereiche, in denen ein Risiko des Verfangens in

beweglichen Teilen besteht

Spécification pour l’habillement de protection destiné à être utilisé en cas de risque de

happement par des pièces de machines en mouvement
Ta slovenski standard je istoveten z: EN 510:2019
ICS:
13.340.10 Varovalna obleka Protective clothing
SIST EN 510:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 510:2020
---------------------- Page: 2 ----------------------
SIST EN 510:2020
EN 510
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2019
EUROPÄISCHE NORM
ICS 13.340.10 Supersedes EN 510:1993
English Version
Specification for protective clothing for use where there is
a risk of entanglement with moving parts

Spécification pour l'habillement de protection destiné à Festlegungen für Schutzkleidungen für Bereiche, in

être utilisé en cas de risque de happement par des denen ein Risiko des Verfangens in beweglichen Teilen

pièces de machines en mouvement besteht
This European Standard was approved by CEN on 23 September 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 510:2019 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 510:2020
EN 510:2019 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

Introduction .................................................................................................................................................................... 4

1 Scope .................................................................................................................................................................... 5

2 Normative references .................................................................................................................................... 5

3 Terms and definitions ................................................................................................................................... 5

4 Requirements ................................................................................................................................................... 5

5 Dimensional change ....................................................................................................................................... 7

6 General size designation............................................................................................................................... 7

7 Marking ............................................................................................................................................................... 7

8 Information supplied by the manufacturer ........................................................................................... 8

Annex A (informative) Rationale and specific features .................................................................................. 9

Annex B (informative) Significant changes between this document and the previous edition .... 10

Annex ZA (informative) Relationship between this European Standard and the essential

requirements of Regulation (EU) 2016/425 of the European Parliament and of the

Council of 9 March 2016 on personal protective equipment aimed to be covered.............. 11

Bibliography ................................................................................................................................................................. 12

---------------------- Page: 4 ----------------------
SIST EN 510:2020
EN 510:2019 (E)
European foreword

This document (EN 510:2019) has been prepared by Technical Committee CEN/TC 162 “Protective

clothing including hand and arm protection and lifejackets”, the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by May 2020, and conflicting national standards shall be

withdrawn at the latest by May 2020.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 510:1993.

This document has been prepared under a standardization request given to CEN by the European

Commission and the European Free Trade Association, and supports essential requirements of

EU Regulation.

For relationship with EU Regulation, see informative Annex ZA, which is an integral part of this

document.

The most technical significant changes in this document in comparison to the previous edition are listed

in Annex B.

According to the CEN-CENELEC Internal Regulations, the national standards organisations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of

North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

United Kingdom.
---------------------- Page: 5 ----------------------
SIST EN 510:2020
EN 510:2019 (E)
Introduction

This document applies to specific garments to be worn when the risk of entanglement cannot be

effectively controlled by physically safeguarding moving parts of machines.
---------------------- Page: 6 ----------------------
SIST EN 510:2020
EN 510:2019 (E)
1 Scope

This document specifies design requirements of protective garments that minimize the risk of its

entanglement or drawing-in by moving parts when the wearer is working at or near hazardous moving

machines or devices, complementary to the general requirements as stated in EN ISO 13688.

This document does not include protective clothing against injuries by special moving machine parts for

which specific standards exist, e.g. protective clothing for user of chainsaws (EN ISO 11393).

2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

EN ISO 13688:2013, Protective clothing - General requirements (ISO 13688:2013)
3 Terms and definitions
No terms and definitions are listed in this document.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
4 Requirements
4.1 General
The requirements of EN ISO 13688:2013 reg
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Festlegungen für Schutzkleidungen für Bereiche, in denen ein Risiko des Verfangens in beweglichen Teilen bestehtSpécification pour l’habillement de protection destiné à être utilisé en cas de risque de happement par des pièces de machines en mouvementSpecification for protective clothing for use where there is a risk of entanglement with moving parts13.340.10Varovalna oblekaProtective clothingICS:Ta slovenski standard je istoveten z:prEN 510oSIST prEN 510:2018en,fr,de01-oktober-2018oSIST prEN 510:2018SLOVENSKI

STANDARD
oSIST prEN 510:2018
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
DRAFT prEN 510
August
t r s z ICS
s uä u v rä s r Will supersede EN
w s rã s { { uEnglish Version

Specification for protective clothing for use where there is a risk of entanglement with moving parts Spécification pour l 5habillement de protection destiné à être utilisé en cas de risque de happement par des pièces de machines en mouvement

Festlegungen für Schutzkleidungen für Bereicheá in denen ein Risiko des Verfangens in beweglichen Teilen besteht This draft European Standard is submitted to CEN members for enquiryä It has been drawn up by the Technical Committee

If this draft becomes a European Standardá CEN members are bounwhich stipulate the conditions for giving this European Standard the status of a national standard without any alterationä

This draft European Standard was established by CEN in three ofer language made by translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä

CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä

Recipients of this draft are invited to submitá with their commentsá notification of any relevant patent rights of which they are aware and to provide supporting documentationä

Warning ã This document is not a European Standardä It is distributed for review and commentsä It is subject to change without notice and shall not be referred to as a European Standardä

EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels

t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä prEN

w s rã t r s z EoSIST prEN 510:2018

prEN 510:2018 (E) 2 Contents Page European foreword ....................................................................................................................................................... 3 Introduction .................................................................................................................................................................... 4 1 Scope .................................................................................................................................................................... 5 2 Normative references .................................................................................................................................... 5 3 Terms and definitions ................................................................................................................................... 5 4 Requirements ................................................................................................................................................... 5 4.1 General ................................................................................................................................................................ 5 4.2 Design .................................................................................................................................................................. 5 4.2.1 Basic design requirements .......................................................................................................................... 5 4.2.2 Additional design requirements in relation to the garment type ................................................. 6 5 Dimensional change ....................................................................................................................................... 7 6 General size designation............................................................................................................................... 7 7 Marking ............................................................................................................................................................... 7 8 Information supplied by the manufacturer ........................................................................................... 7 Annex A (informative)

Rationale and specific features .................................................................................. 8 A.1 Rationale ............................................................................................................................................................ 8 A.2 Specific features (optional) ......................................................................................................................... 8 Annex B (informative)

Significant changes between this document and the previous edition ....... 9 Annex ZA (informative)

Relationship between this European Standard and the essential requirements of Regulation (EU) 2016/425 of the European Parliament and of the Council of 9 March 2016 on personal protective equipment aimed to be covered.............. 10

oSIST prEN 510:2018

prEN 510:2018 (E) 3 European foreword This document (prEN 510:2018) has been prepared by Technical Committee CEN/TC 162 “Protective clothing including hand and arm protection and lifejackets”, the secretariat of which is held by DIN. This document is currently submitted to the CEN Enquiry. This document will supersede EN 510:1993. This document has been prepared under a standardization request given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Regulation. For relationship with EU Regulation, see informative Annex ZA, which is an integral part of this document. The most technical significant changes in this document in comparison to the previous edition are listed in Annex B. oSIST prEN 510:2018

prEN 510:2018 (E) 4 Introduction This document applies to specific garments to be worn when the risk of entanglement cannot be effectively controlled by physically safeguarding moving parts of machines. oSIST prEN 510:2018

prEN 510:2018 (E) 5 1 Scope This document specifies design requirements of protective garments that minimize the risk of its entanglement or drawing-in by moving parts when the wearer is working at or near hazardous moving machines or devices, complementary to the general requirements as stated in EN ISO 13688. This document does not include protective clothing against injuries by special moving machine parts for which specific standards exist, e.g. protective clothing for user of chainsaws (EN ISO 11393). 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 13688:2013, Protective clothing - General requirements (ISO 13688:2013) 3 Terms and definitions No terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.