SIST EN ISO 15612:2018

Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2018)

This document:
— specifies how a user can follow a standard welding procedure specification (SWPS) based on
welding procedure qualification tests performed by a different organization;
— specifies the range for the use of SWPSs in accordance with ISO 15607;
— specifies the requirements for qualification of welding procedures to be issued as SWPSs; and
— specifies the requirements for organizations adopting SWPSs.
The use of this document can be restricted by an application standard or a specification.
This document is applicable to welding of steels and aluminium and its alloys (see 4.1).
All new standard welding procedure qualifications are to be carried out in accordance with this
document from the date of its issue. However, this document does not invalidate previous standard
welding procedure qualifications made to former standards, specifications or previous editions of this
document.

Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe - Qualifizierung durch Einsatz eines Standardschweißverfahrens (ISO 15612:2018)

Dieses Dokument:
-   legt fest, wie ein Anwender eine Schweißanweisung für Standardschweißverfahren (SWPS) auf der Grundlage von Prüfungen zur Qualifizierung von Schweißverfahren befolgen kann, die von einer anderen Organisation durchgeführt wurden;
-   legt den Anwendungsbereich für SWPS in Übereinstimmung mit ISO 15607 fest;
-   legt die Anforderungen für die Qualifizierung von Schweißverfahren fest, die als SWPS veröffentlicht werden sollen; und
-   legt die Anforderungen an Organisationen fest, die SWPS anwenden.
Die Anwendung dieses Dokuments kann durch eine Anwendungsnorm oder durch eine Spezifikation eingeschränkt werden.
Dieses Dokument gilt für das Schweißen von Stählen und Aluminium und Aluminiumlegierungen (siehe 4.1).
Alle neuen Qualifizierungen von Standardschweißverfahren müssen ab dem Zeitpunkt der Veröffentlichung dieses Dokuments nach ihm qualifiziert werden. Dieses Dokument setzt jedoch bereits bestehende Qualifizierungen von Standardschweißverfahren, die nach früheren Normen oder Spezifikationen oder früheren Ausgaben dieses Dokuments durchgeführt wurden, nicht außer Kraft.

Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques - Qualification par référence à un mode opératoire de soudage standard (ISO 15612:2018)

Le présent document:
—         spécifie comment un utilisateur peut suivre un mode opératoire de soudage standard basé sur des épreuves de qualification d'un mode opératoire de soudage effectuées une autre organisation;
—         spécifie le domaine de validité des modes opératoires de soudage standards, conformément à l'ISO 15607
—         spécifie les exigences pour la qualification des modes opératoires de soudage devant être publiés en tant que descriptif d'un mode opératoire de soudage standard; et
—         spécifie les exigences pour les organismes adoptant un mode opératoire de soudage standard.
L'emploi du présent document peut être limité par une norme d'application ou par une spécification.
Le présent document est applicable au soudage des aciers, de l'aluminium et des alliages d'aluminium (voir 4.1).
Toutes les nouvelles qualifications par référence à un mode opératoire de soudage standard doivent être effectuées conformément au présent document dès parution. Toutefois, le présent document n'invalide pas les qualifications par référence à un mode opératoire de soudage standard antérieures, exécutées selon d'anciennes normes, spécifications, ou selon des éditions précédentes du présent document.

Specifikacija in kvalifikacija varilnih postopkov za kovinske materiale - Kvalifikacija na podlagi standardnega varilnega postopka (ISO 15612:2018)

Ta dokument:
– določa, kako lahko uporabnik upošteva specifikacijo standardnega varilnega postopka (SWPS) na podlagi kvalifikacijskih preskusov varilnih postopkov, ki jih je izvedla druga organizacija;
– določa obseg uporabe specifikacij standardnih varilnih postopkov v skladu s standardom ISO 15607;
– določa zahteve za kvalifikacijo varilnih postopkov, ki nameravajo biti objavljeni kot specifikacije standardnih varilnih postopkov; in
– določa zahteve za organizacije, ki sprejemajo specifikacije standardnih varilnih postopkov.
Uporabo tega dokumenta je mogoče omejiti s standardom za uporabo ali specifikacijo. Ta dokument se uporablja za varjenje jekel in aluminija ter njegovih zlitin (glej točko 4.1). Vse nove kvalifikacije standardnih varilnih postopkov je treba izvesti v skladu s tem dokumentom od datuma njegove objave. Vendar ta dokument ne razveljavlja prejšnjih kvalifikacij standardnih varilnih postopkov, ki so del preteklih standardov, specifikacij ali izdaj tega dokumenta.

General Information

• Status: Published
• Public Enquiry End Date: 24-Oct-2016
• Publication Date: 17-Sep-2018
• ICS: 25.160.10 - Welding processes
• Technical Committee: VAR - Welding
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 23-Aug-2018
• Due Date: 28-Oct-2018
• Completion Date: 18-Sep-2018
• Ref Project: EN ISO 15612:2018 - Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure specification (ISO 15612:2018)

Relations

• Replaces: SIST EN ISO 15612:2004 - Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004)
• Effective Date: 01-Oct-2018

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15612:2018
01-oktober-2018
1DGRPHãþD
SIST EN ISO 15612:2004
Specifikacija in kvalifikacija varilnih postopkov za kovinske materiale -
Kvalifikacija na podlagi standardnega varilnega postopka (ISO 15612:2018)
Specification and qualification of welding procedures for metallic materials - Qualification
by adoption of a standard welding procedure (ISO 15612:2018)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe -
Qualifizierung durch Einsatz eines Standardschweißverfahrens (ISO 15612:2018)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux
métalliques - Qualification par référence à un mode opératoire de soudage standard
(ISO 15612:2018)
Ta slovenski standard je istoveten z: EN ISO 15612:2018
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
SIST EN ISO 15612:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15612:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 15612:2018


EN ISO 15612
EUROPEAN STANDARD

NORME EUROPÉENNE

July 2018
EUROPÄISCHE NORM
ICS 25.160.10 Supersedes EN ISO 15612:2004
English Version

Specification and qualification of welding procedures for
metallic materials - Qualification by adoption of a standard
welding procedure (ISO 15612:2018)
Descriptif et qualification d'un mode opératoire de Anforderung und Qualifizierung von Schweißverfahren
soudage pour les matériaux métalliques - Qualification für metallische Werkstoffe - Qualifizierung durch
par référence à un mode opératoire de soudage Einsatz eines Standardschweißverfahrens (ISO
standard (ISO 15612:2018) 15612:2018)
This European Standard was approved by CEN on 24 June 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15612:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15612:2018
EN ISO 15612:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 15612:2018
EN ISO 15612:2018 (E)
European foreword
This document (EN ISO 15612:2018) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2019, and conflicting national standards shall
be withdrawn at the latest by January 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15612:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 15612:2018 has been approved by CEN as EN ISO 15612:2018 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 15612:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 15612:2018
INTERNATIONAL ISO
STANDARD 15612
Second edition
2018-06
Specification and qualification of
welding procedures for metallic
materials — Qualification by adoption
of a standard welding procedure
specification
Descriptif et qualification d'un mode opératoire de soudage pour
les matériaux métalliques — Qualification par référence à un mode
opératoire de soudage standard
Reference number
ISO 15612:2018(E)
©
ISO 2018

---------------------- Page: 7 ----------------------

SIST EN ISO 15612:2018
ISO 15612:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 15612:2018
ISO 15612:2018(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Limits on use of and publication of an SWPS .2
4.1 General . 2
4.2 Limits on the use of SWPSs . 2
4.2.1 General. 2
4.2.2 Parent material thickness . 2
4.2.3 Parent material . 3
5 Adoption of an SWPS .3
5.1 General . 3
5.2 Related to the user of an SWPS . 3
6 Validity .4
7 Preparation and documentation .4
Bibliography .5
© ISO 2018 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 15612:2018
ISO 15612:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
descri
...