Broadcast Sound Receivers - Part 1: Generic requirements and measuring methods

The present document specifies generic requirements and methods of measurements for devices, including the supplied
antenna, that receive broadcast sound services, whether analogue or digital modulation is used to meet the essential
requirements of article 3.2 of Directive 2014/53/EU [i.1]. Subsequent parts of this multi-part deliverable provide the
necessary test signal configurations and limits for the different broadcast sound services. Multi-function devices may
also fall under the requirements of other documents.

Radiodifuzijski zvočni sprejemniki - 1. del: Generične zahteve in merilne metode

Ta dokument določa generične zahteve in merilne metode za naprave, vključno z dobavljeno anteno, ki sprejemajo zvokovne radiodifuzijske storitve, odvisno od tega, ali uporabljena analogna ali digitalna modulacija izpolnjuje bistvene zahteve iz člena 3.2 Direktive 2014/53/EU [i.1]. Naslednji deli tega večdelnega dokumenta zagotavljajo
potrebne konfiguracije preskusnih signalov in omejitve za različne zvokovno radiodifuzijske storitve. Za večfunkcijske naprave lahko veljajo tudi zahteve iz drugih dokumentov.

General Information

Status
Published
Public Enquiry End Date
24-Dec-2018
Publication Date
25-Jun-2019
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
17-Jun-2019
Due Date
22-Aug-2019
Completion Date
26-Jun-2019

Buy Standard

Standard
ETSI EN 303 345-1 V1.1.1 (2019-06) - Broadcast Sound Receivers; Part 1: Generic requirements and measuring methods
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 303 345-1 V1.1.1 (2019-03) - Broadcast Sound Receivers; Part 1: Generic requirements and measuring methods
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
EN 303 345-1 V1.1.1:2019
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ETSI EN 303 345-1 V1.1.0 (2018-09) - Broadcast Sound Receivers; Part 1: Generic requirements and measuring methods
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
prEN 303 345-1 V1.1.0:2018
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

ETSI EN 303 345-1 V1.1.1 (2019-06)






EUROPEAN STANDARD
Broadcast Sound Receivers;
Part 1: Generic requirements and measuring methods



---------------------- Page: 1 ----------------------
2 ETSI EN 303 345-1 V1.1.1 (2019-06)



Reference
DEN/ERM-TG17-151
Keywords
broadcast, digital, radio, receiver
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 303 345-1 V1.1.1 (2019-06)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical requirements specifications . 8
4.1 Environmental profile . 8
4.2 Conformance requirements . 8
4.2.1 Broadcast radio modulation methods . 8
4.2.2 Broadcast radio frequency bands . 8
5 Testing for compliance with technical requirements . 9
5.1 Environmental conditions for testing . 9
5.2 Interpretation of the measurement results . 9
5.3 Methods of measurement . 9
5.3.1 Generic methods of measurement . 9
5.3.2 Generic measurement set-up for radiated testing . 10
5.3.3 Generic measurement set-up for conducted testing . 13
5.3.4 Sensitivity measurement methods . 14
5.3.4.1 Analogue (AM and FM) sensitivity measurements. 14
5.3.4.2 Digital (DAB and DRM) sensitivity measurements . 14
5.3.5 Adjacent channel selectivity and blocking measurement methods . 14
5.3.5.1 Analogue (AM and FM) adjacent channel selectivity and blocking measurements . 14
5.3.5.2 Digital (DAB and DRM) adjacent channel selectivity and blocking measurements . 15
Annex A (informative): A fibre-optic link for receiver testing . 16
Annex B (informative): Measurement set-up for electrical methods during radiated testing . 18
Annex C (informative): Change History . 19
History . 20


ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 303 345-1 V1.1.1 (2019-06)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and
Radio spectrum Matters (ERM).
The present document is part 1 of a multi-part deliverable covering the requirements and measuring methods for
broadcast sound receivers to meet the essential requirements of article 3.2 of Directive 2014/53/EU [i.1], as identified
below:
Part 1: "Generic requirements and measuring methods";
Part 2: "AM broadcast sound service";
Part 3: "FM broadcast sound service";
Part 4: "DAB broadcast sound service";
Part 5: "DRM broadcast sound service".
The test data files are contained in archive en_30334501v010101p0.zip which accompanies the present document.

National transposition dates
Date of adoption of this EN: 27 May 2019
Date of latest announcement of this EN (doa): 31 August 2019
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 29 February 2020
Date of withdrawal of any conflicting National Standard (dow): 28 February 2021

ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 303 345-1 V1.1.1 (2019-06)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 303 345-1 V1.1.1 (2019-06)
1 Scope
The present document specifies generic requirements and methods of measurements for devices, including the supplied
antenna, that receive broadcast sound services, whether analogue or digital modulation is used to meet the essential
requirements of article 3.2 of Directive 2014/53/EU [i.1]. Subsequent parts of this multi-part deliverable provide the
necessary test signal configurations and limits for the different broadcast sound services. Multi-function devices may
also fall under the requirements of other documents.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CENELEC EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission
Requirements".
[2] IEC 60315-1 (1988): "Methods of measurement on radio receivers for various classes of emission.
Part 1: General considerations and methods of measurement, including audio-frequency
measurements".
[3] Recommendation ITU-R BS.468-4 (07/1986): "Measurement of audio-frequency noise voltage
level in sound broadcasting".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI TR 100 028 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics".
[i.3] ETSI TR 100 028-2: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 2".
[i.4] ECA table in ERC report 25.
NOTE: Available at www.efis.dk.
ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 303 345-1 V1.1.1 (2019-06)
[i.5] CISPR 35: "Electromagnetic Compatibility of Multimedia equipment - Immunity Requirements".
[i.6] BBC Research & Development White Paper WHP 335: "A Fibre-Optic Link for Use During
Receiver Testing".
NOTE: Available at http://downloads.bbc.co.uk/rd/pubs/whp/whp-pdf-files/WHP335.pdf.
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in Directive 2014/53/EU [i.1] and the following apply:
adjacent channel selectivity: at a given frequency separation, ratio of the maximum unwanted signal level to the
wanted signal level necessary to provide a given level of audio quality
blocking: at a given frequency separation, ratio of the maximum AM unwanted signal level to the wanted signal level
necessary to provide a given level of audio quality
built-in antenna: antenna that cannot be detached from the equipment
dBm: decibels relative to 1 mW of power
external antenna: antenna designed to be connected to the equipment with the use of a 50 Ω or 75 Ω external
connector
integral antenna: antenna which is detachable from the equipment without the use of any tools, and not using a 50 Ω
or 75 Ω external connector
NOTE: A device that uses a supplied earphone as the antenna has an integral antenna.
sensitivity: minimum wanted signal level required to provide a given level of audio quality
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AM Amplitude Modulation
AMSS Amplitude Modulation Signalling System
BBC British Broadcasting Corporation
BS Broadcast service (Sound)
CISPR Comité International Spécial des Perturbations Radioélectriques
CMAD Common Mode Absorption Device
DAB Digital Audio Broadcasting
DRM Digital Radio Mondiale
EC European Commission
ECA European Common Allocation
EU European Union
FAR Fully Anechoic Room
FM Frequency Modulation
GTEM Gigahertz Transverse ElectroMagnetic
HF High Frequency
IEC International Electrotechnical Commission
ITU-R International Telecommunications Union - Radiocommunications
LED Light Emitting Diode
ETSI

---------------------- Page: 7 ----------------------
8 ETSI EN 303 345-1 V1.1.1 (2019-06)
LF Low Frequency
MF Medium Frequency
RDS Radio Data System
RF Radio Frequency
RUT Receiver Under Test
S/PDIF Sony/Philips Digital InterFace
SAC Semi Anechoic Chamber
THD Total Harmonic Distortion
THD+N Total Harmonic Distortion plus Noise
UI User Interface
VHF Very High Frequency
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the manufacturer.
4.2 Conformance requirements
4.2.1 Broadcast radio modulation methods
The following broadcast radio modulation methods are considered feasible within the current authorization regime in
Europe:
• Amplitude modulation, with or without AMSS (AM).
• Frequency modulation, with or without RDS (FM).
• Digital Audio Broadcasting (DAB).
• Digital Radio Mondiale (DRM).
Broadcast radio receivers may include demodulation capability for one or more of these modulation methods.
Conformance shall only be required for each of the modulation methods included in the receiver.
4.2.2 Broadcast radio frequency bands
The following frequency bands are identified in the ECA table [i.4] for broadcast radio services:
• Low frequency (LF): 148,5 kHz to 283,5 kHz.
• Medium frequency (MF): 526,5 kHz to 1 606,5 kHz.
• High Frequency (HF): 3 950 kHz to 4 000 kHz, 5 900 kHz to 6 200 kHz, 7 200 kHz to 7 450 kHz, 9 400 kHz
to 9 900 kHz, 11 600 kHz to 12 100 kHz, 13 570 kHz to 13 870 kHz, 15 100 kHz to 15 800 kHz, 17 480 kHz
to 17 900 kHz, 18 900 kHz to 19 020 kHz, 21 450 kHz to 21 850 kHz and 25 670 kHz to 26 100 kHz.
• VHF band I: 47 MHz to 68 MHz.
• VHF band II: 87,5 MHz to 108 MHz.
• VHF band III: 174 MHz to 240 MHz.
Broadcast radio receivers may include tuning capability for one or more of these frequency bands. Conformance shall
only be required for each of the frequency bands included in the receiver.
ETSI

---------------------- Page: 8 ----------------------
9 ETSI EN 303 345-1 V1.1.1 (2019-06)
5 Testing for compliance with technical requirements
5.1 Environmental conditions for testing
The equipment shall be tested under normal test conditions according to the relevant product and basic standards or to
the information accompanying the equipment, which are within the manufacturers declared range of humidity,
temperature and supply voltage. The test conditions shall be recorded in the test report.
5.2 Interpretation of the measurement results
The interpretation of the results recorded in a test report for the measurements described in the present document shall
be as follows:
• the measured value related to the corresponding limit will be used to decide whether an equipment meets the
requirements of the present document;
• the value of the measurement uncertainty for the measurement of each parameter shall be included in the test
report;
• the recorded value of the measurement uncertainty shall be, for each measurement, equal to or less than the
figures in table 1.
For the test methods, according to the present document, the measurement uncertainty figures shall be calculated and
shall correspond to an expansion factor (coverage factor) k = 1,96 or k = 2 (which provide confidence levels of
respectively 95 % and 95,45 % in the case where the distributions characterizing the actual measurement uncertainties
are normal (Gaussian)). Principles for the calculation of measurement uncertainty are contained in ETSI
TR 100 028 [i.2], in particular in annex D of the ETSI TR 100 028-2 [i.3].
Table 1 is based on such expansion factors.
Table 1: Maximum measurement uncertainty
Parameter Uncertainty
Uncertainty in conducted measurements ±1 dB
Uncertainty in radiated measurements ±6 dB

5.3 Methods of measurement
5.3.1 Generic methods of measurement
Two generic methods of measurement are applicable to verifying the performance of the receiving equipment in
question. The conducted test methods shall be used for receivers with an external antenna connector. The radiated test
methods shall be used for all other receivers.
For both generic methods, two generators are needed. One provides the wanted signal, and the other the unwanted
signal, or interferer (when required). The two signals are combined in such a way as to maintain isolation between the
generators. It is necessary to provide calibrated attenuators for control of the individual levels; very often these will be
built into the generators. Where the attenuators are external, cable lengths should be kept short to avoid cross-coupling
effects.
The tests require the audio output of the receiver to be measured. All tonal controls (user operated and/or preset,
...

Final draft ETSI EN 303 345-1 V1.1.1 (2019-03)






EUROPEAN STANDARD
Broadcast Sound Receivers;
Part 1: Generic requirements and measuring methods



---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 303 345-1 V1.1.1 (2019-03)



Reference
DEN/ERM-TG17-151
Keywords
broadcast, digital, radio, receiver
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 303 345-1 V1.1.1 (2019-03)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical requirements specifications . 8
4.1 Environmental profile . 8
4.2 Conformance requirements . 8
4.2.1 Broadcast radio modulation methods . 8
4.2.2 Broadcast radio frequency bands . 8
5 Testing for compliance with technical requirements . 9
5.1 Environmental conditions for testing . 9
5.2 Interpretation of the measurement results . 9
5.3 Methods of measurement . 9
5.3.1 Generic methods of measurement . 9
5.3.2 Generic measurement set-up for radiated testing . 10
5.3.3 Generic measurement set-up for conducted testing . 13
5.3.4 Sensitivity measurement methods . 14
5.3.4.1 Analogue (AM and FM) sensitivity measurements. 14
5.3.4.2 Digital (DAB and DRM) sensitivity measurements . 14
5.3.5 Adjacent channel selectivity and blocking measurement methods . 14
5.3.5.1 Analogue (AM and FM) adjacent channel selectivity and blocking measurements . 14
5.3.5.2 Digital (DAB and DRM) adjacent channel selectivity and blocking measurements . 15
Annex A (informative): A fibre-optic link for receiver testing . 16
Annex B (informative): Measurement set-up for electrical methods during radiated testing . 18
Annex C (informative): Change History . 19
History . 20


ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 303 345-1 V1.1.1 (2019-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This final draft European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the ETSI standards EN
Approval Procedure.
The present document is part 1 of a multi-part deliverable covering the requirements and measuring methods for
broadcast sound receivers to meet the essential requirements of article 3.2 of Directive 2014/53/EU [i.1], as identified
below:
Part 1: "Generic requirements and measuring methods";
Part 2: "AM broadcast sound service";
Part 3: "FM broadcast sound service";
Part 4: "DAB broadcast sound service";
Part 5: "DRM broadcast sound service".
The test data files are contained in archive en_30334501v010101v0.zip which accompanies the present document.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 303 345-1 V1.1.1 (2019-03)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 303 345-1 V1.1.1 (2019-03)
1 Scope
The present document specifies generic requirements and methods of measurements for devices, including the supplied
antenna, that receive broadcast sound services, whether analogue or digital modulation is used to meet the essential
requirements of article 3.2 of Directive 2014/53/EU [i.1]. Subsequent parts of this multi-part deliverable provide the
necessary test signal configurations and limits for the different broadcast sound services. Multi-function devices may
also fall under the requirements of other documents.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CENELEC EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission
Requirements".
[2] IEC 60315-1 (1988): "Methods of measurement on radio receivers for various classes of emission.
Part 1: General considerations and methods of measurement, including audio-frequency
measurements".
[3] Recommendation ITU-R BS.468-4 (07/1986): "Measurement of audio-frequency noise voltage
level in sound broadcasting".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI TR 100 028 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics".
[i.3] ETSI TR 100 028-2: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 2".
[i.4] ECA table in ERC report 25.
NOTE: Available at www.efis.dk.
ETSI

---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 303 345-1 V1.1.1 (2019-03)
[i.5] CISPR 35: "Electromagnetic Compatibility of Multimedia equipment - Immunity Requirements".
[i.6] BBC Research & Development White Paper WHP 335: "A Fibre-Optic Link for Use During
Receiver Testing".
NOTE: Available at http://downloads.bbc.co.uk/rd/pubs/whp/whp-pdf-files/WHP335.pdf.
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in Directive 2014/53/EU [i.1] and the following apply:
adjacent channel selectivity: at a given frequency separation, ratio of the maximum unwanted signal level to the
wanted signal level necessary to provide a given level of audio quality
blocking: at a given frequency separation, ratio of the maximum AM unwanted signal level to the wanted signal level
necessary to provide a given level of audio quality
built-in antenna: antenna that cannot be detached from the equipment
dBm: decibels relative to 1 mW of power
external antenna: antenna designed to be connected to the equipment with the use of a 50 Ω or 75 Ω external
connector
integral antenna: antenna which is detachable from the equipment without the use of any tools, and not using a 50 Ω
or 75 Ω external connector
NOTE: A device that uses a supplied earphone as the antenna has an integral antenna.
sensitivity: minimum wanted signal level required to provide a given level of audio quality
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AM Amplitude Modulation
AMSS Amplitude Modulation Signalling System
BBC British Broadcasting Corporation
BS Broadcast service (Sound)
CISPR Comité International Spécial des Perturbations Radioélectriques
CMAD Common Mode Absorption Device
DAB Digital Audio Broadcasting
DRM Digital Radio Mondiale
EC European Commission
ECA European Common Allocation
EU European Union
FAR Fully Anechoic Room
FM Frequency Modulation
GTEM Gigahertz Transverse ElectroMagnetic
HF High Frequency
IEC International Electrotechnical Commission
ITU-R International Telecommunications Union - Radiocommunications
LED Light Emitting Diode
ETSI

---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 303 345-1 V1.1.1 (2019-03)
LF Low Frequency
MF Medium Frequency
RDS Radio Data System
RF Radio Frequency
RUT Receiver Under Test
S/PDIF Sony/Philips Digital InterFace
SAC Semi Anechoic Chamber
THD Total Harmonic Distortion
THD+N Total Harmonic Distortion plus Noise
UI User Interface
VHF Very High Frequency
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the manufacturer.
4.2 Conformance requirements
4.2.1 Broadcast radio modulation methods
The following broadcast radio modulation methods are considered feasible within the current authorization regime in
Europe:
• Amplitude modulation, with or without AMSS (AM).
• Frequency modulation, with or without RDS (FM).
• Digital Audio Broadcasting (DAB).
• Digital Radio Mondiale (DRM).
Broadcast radio receivers may include demodulation capability for one or more of these modulation methods.
Conformance shall only be required for each of the modulation methods included in the receiver.
4.2.2 Broadcast radio frequency bands
The following frequency bands are identified in the ECA table [i.4] for broadcast radio services:
• Low frequency (LF): 148,5 kHz to 283,5 kHz.
• Medium frequency (MF): 526,5 kHz to 1 606,5 kHz.
• High Frequency (HF): 3 950 kHz to 4 000 kHz, 5 900 kHz to 6 200 kHz, 7 200 kHz to 7 450 kHz, 9 400 kHz
to 9 900 kHz, 11 600 kHz to 12 100 kHz, 13 570 kHz to 13 870 kHz, 15 100 kHz to 15 800 kHz, 17 480 kHz
to 17 900 kHz, 18 900 kHz to 19 020 kHz, 21 450 kHz to 21 850 kHz and 25 670 kHz to 26 100 kHz.
• VHF band I: 47 MHz to 68 MHz.
• VHF band II: 87,5 MHz to 108 MHz.
• VHF band III: 174 MHz to 240 MHz.
Broadcast radio receivers may include tuning capability for one or more of these frequency bands. Conformance shall
only be required for each of the frequency bands included in the receiver.
ETSI

---------------------- Page: 8 ----------------------
9 Final draft ETSI EN 303 345-1 V1.1.1 (2019-03)
5 Testing for compliance with technical requirements
5.1 Environmental conditions for testing
The equipment shall be tested under normal test conditions according to the relevant product and basic standards or to
the information accompanying the equipment, which are within the manufacturers declared range of humidity,
temperature and supply voltage. The test conditions shall be recorded in the test report.
5.2 Interpretation of the measurement results
The interpretation of the results recorded in a test report for the measurements described in the present document shall
be as follows:
• the measured value related to the corresponding limit will be used to decide whether an equipment meets the
requirements of the present document;
• the value of the measurement uncertainty for the measurement of each parameter shall be included in the test
report;
• the recorded value of the measurement uncertainty shall be, for each measurement, equal to or less than the
figures in table 1.
For the test methods, according to the present document, the measurement uncertainty figures shall be calculated and
shall correspond to an expansion factor (coverage factor) k = 1,96 or k = 2 (which provide confidence levels of
respectively 95 % and 95,45 % in the case where the distributions characterizing the actual measurement uncertainties
are normal (Gaussian)). Principles for the calculation of measurement uncertainty are contained in ETSI
TR 100 028 [i.2], in particular in annex D of the ETSI TR 100 028-2 [i.3].
Table 1 is based on such expansion factors.
Table 1: Maximum measurement uncertainty
Parameter Uncertainty
Uncertainty in conducted measurements ±1 dB
Uncertainty in radiated measurements ±6 dB

5.3 Methods of measurement
5.3.1 Generic methods of measurement
Two generic methods of measurement are applicable to verifying the performance of the receiving equipment in
question. The conducted test methods shall be used for receivers with an external antenna connector. The radiated test
methods shall be used for all other receivers.
For both generic methods, two generators are needed. One provides the wanted signal, and the other the unwanted
signal, or interferer (when required). The two signals are combined in such a way as to maintain isolation between the
generators. It is necessary to provide calibrated attenuators for control of the individual levels; very often these will be
built into the generators. Where the attenuators are external, cable lengths should be kept short to avoid cross-coupling
effects.
The tests require the audio output of the receiver to be measured. All ton
...

SLOVENSKI STANDARD
SIST EN 303 345-1 V1.1.1:2019
01-september-2019
Radiodifuzijski zvočni sprejemniki - 1. del: Generične zahteve in merilne metode
Broadcast Sound Receivers - Part 1: Generic requirements and measuring methods
Ta slovenski standard je istoveten z: ETSI EN 303 345-1 V1.1.1 (2019-06)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
SIST EN 303 345-1 V1.1.1:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 303 345-1 V1.1.1:2019

---------------------- Page: 2 ----------------------

SIST EN 303 345-1 V1.1.1:2019
ETSI EN 303 345-1 V1.1.1 (2019-06)






EUROPEAN STANDARD
Broadcast Sound Receivers;
Part 1: Generic requirements and measuring methods



---------------------- Page: 3 ----------------------

SIST EN 303 345-1 V1.1.1:2019

2 ETSI EN 303 345-1 V1.1.1 (2019-06)



Reference
DEN/ERM-TG17-151
Keywords
broadcast, digital, radio, receiver
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------

SIST EN 303 345-1 V1.1.1:2019

3 ETSI EN 303 345-1 V1.1.1 (2019-06)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical requirements specifications . 8
4.1 Environmental profile . 8
4.2 Conformance requirements . 8
4.2.1 Broadcast radio modulation methods . 8
4.2.2 Broadcast radio frequency bands . 8
5 Testing for compliance with technical requirements . 9
5.1 Environmental conditions for testing . 9
5.2 Interpretation of the measurement results . 9
5.3 Methods of measurement . 9
5.3.1 Generic methods of measurement . 9
5.3.2 Generic measurement set-up for radiated testing . 10
5.3.3 Generic measurement set-up for conducted testing . 13
5.3.4 Sensitivity measurement methods . 14
5.3.4.1 Analogue (AM and FM) sensitivity measurements. 14
5.3.4.2 Digital (DAB and DRM) sensitivity measurements . 14
5.3.5 Adjacent channel selectivity and blocking measurement methods . 14
5.3.5.1 Analogue (AM and FM) adjacent channel selectivity and blocking measurements . 14
5.3.5.2 Digital (DAB and DRM) adjacent channel selectivity and blocking measurements . 15
Annex A (informative): A fibre-optic link for receiver testing . 16
Annex B (informative): Measurement set-up for electrical methods during radiated testing . 18
Annex C (informative): Change History . 19
History . 20


ETSI

---------------------- Page: 5 ----------------------

SIST EN 303 345-1 V1.1.1:2019

4 ETSI EN 303 345-1 V1.1.1 (2019-06)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and
Radio spectrum Matters (ERM).
The present document is part 1 of a multi-part deliverable covering the requirements and measuring methods for
broadcast sound receivers to meet the essential requirements of article 3.2 of Directive 2014/53/EU [i.1], as identified
below:
Part 1: "Generic requirements and measuring methods";
Part 2: "AM broadcast sound service";
Part 3: "FM broadcast sound service";
Part 4: "DAB broadcast sound service";
Part 5: "DRM broadcast sound service".
The test data files are contained in archive en_30334501v010101p0.zip which accompanies the present document.

National transposition dates
Date of adoption of this EN: 27 May 2019
Date of latest announcement of this EN (doa): 31 August 2019
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 29 February 2020
Date of withdrawal of any conflicting National Standard (dow): 28 February 2021

ETSI

---------------------- Page: 6 ----------------------

SIST EN 303 345-1 V1.1.1:2019

5 ETSI EN 303 345-1 V1.1.1 (2019-06)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 7 ----------------------

SIST EN 303 345-1 V1.1.1:2019

6 ETSI EN 303 345-1 V1.1.1 (2019-06)
1 Scope
The present document specifies generic requirements and methods of measurements for devices, including the supplied
antenna, that receive broadcast sound services, whether analogue or digital modulation is used to meet the essential
requirements of article 3.2 of Directive 2014/53/EU [i.1]. Subsequent parts of this multi-part deliverable provide the
necessary test signal configurations and limits for the different broadcast sound services. Multi-function devices may
also fall under the requirements of other documents.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CENELEC EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission
Requirements".
[2] IEC 60315-1 (1988): "Methods of measurement on radio receivers for various classes of emission.
Part 1: General considerations and methods of measurement, including audio-frequency
measurements".
[3] Recommendation ITU-R BS.468-4 (07/1986): "Measurement of audio-frequency noise voltage
level in sound broadcasting".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI TR 100 028 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics".
[i.3] ETSI TR 100 028-2: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 2".
[i.4] ECA table in ERC report 25.
NOTE: Available at www.efis.dk.
ETSI

---------------------- Page: 8 ----------------------

SIST EN 303 345-1 V1.1.1:2019

7 ETSI EN 303 345-1 V1.1.1 (2019-06)
[i.5] CISPR 35: "Electromagnetic Compatibility of Multimedia equipment - Immunity Requirements".
[i.6] BBC Research & Development White Paper WHP 335: "A Fibre-Optic Link for Use During
Receiver Testing".
NOTE: Available at http://downloads.bbc.co.uk/rd/pubs/whp/whp-pdf-files/WHP335.pdf.
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in Directive 2014/53/EU [i.1] and the following apply:
adjacent channel selectivity: at a given frequency separation, ratio of the maximum unwanted signal level to the
wanted signal level necessary to provide a given level of audio quality
blocking: at a given frequency separation, ratio of the maximum AM unwanted signal level to the wanted signal level
necessary to provide a given level of audio quality
built-in antenna: antenna that cannot be detached from the equipment
dBm: decibels relative to 1 mW of power
external antenna: antenna designed to be connected to the equipment with the use of a 50 Ω or 75 Ω external
connector
integral antenna: antenna which is detachable from the equipment without the use of any tools, and not using a 50 Ω
or 75 Ω external connector
NOTE: A device that uses a supplied earphone as the antenna has an integral antenna.
sensitivity: minimum wanted signal level required to provide a given level of audio quality
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AM Amplitude Modulation
AMSS Amplitude Modulation Signalling System
BBC British Broadcasting Corporation
BS Broadcast service (Sound)
CISPR Comité International Spécial des Perturbations Radioélectriques
CMAD Common Mode Absorption Device
DAB Digital Audio Broadcasting
DRM Digital Radio Mondiale
EC European Commission
ECA European Common Allocation
EU European Union
FAR Fully Anechoic Room
FM Frequency Modulation
GTEM Gigahertz Transverse ElectroMagnetic
HF High Frequency
IEC International Electrotechnical Commission
ITU-R International Telecommunications Union - Radiocommunications
LED Light Emitting Diode
ETSI

---------------------- Page: 9 ----------------------

SIST EN 303 345-1 V1.1.1:2019

8 ETSI EN 303 345-1 V1.1.1 (2019-06)
LF Low Frequency
MF Medium Frequency
RDS Radio Data System
RF Radio Frequency
RUT Receiver Under Test
S/PDIF Sony/Philips Digital InterFace
SAC Semi Anechoic Chamber
THD Total Harmonic Distortion
THD+N Total Harmonic Distortion plus Noise
UI User Interface
VHF Very High Frequency
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the manufacturer.
4.2 Conformance requirements
4.2.1 Broadcast radio modulation methods
The following broadcast radio modulation methods are considered feasible within the current authorization regime in
Europe:
• Amplitude modulation, with or without AMSS (AM).
• Frequency modulation, with or without RDS (FM).
• Digital Audio Broadcasting (DAB).
• Digital Radio Mondiale (DRM).
Broadcast radio receivers may include demodulation capability for one or more of these modulation methods.
Conformance shall only be required for each of the modulation methods included in the receiver.
4.2.2 Broadcast radio frequency bands
The following frequency bands are identified in the ECA table [i.4] for broadcast radio services:
• Low frequency (LF): 148,5 kHz to 283,5 kHz.
• Medium frequency (MF): 526,5 kHz to 1 606,5 kHz.
• High Frequency (HF): 3 950 kHz to 4 000 kHz, 5 900 kHz to 6 200 kHz, 7 200 kHz to 7 450 kHz, 9 400 kHz
to 9 900 kHz, 11 600 kHz to 12 100 kHz, 13 570 kHz to 13 870 kHz, 15 100 kHz to 15 800 kHz, 17 480 kHz
to 17 900 kHz, 18 900 kHz to 19 020 kHz, 21 450 kHz to 21 850 kHz and 25 670 kHz to 26 100 kHz.
• VHF band I: 47 MHz to 68 MHz.
• VHF band II: 87,5 MHz to 108 MHz.
• VHF band III: 174 MHz to 240 MHz.
Broadcast radio receivers may include tuning capability for one or more of these frequency bands. Conformance shall
only be required for each of the frequency bands included in the receiver.
ETSI

---------------------- Page: 10 ----------------------

SIST EN 303 345-1 V1.1.1:2019

9 ETSI EN 303 345-1 V1.1.1 (2019-06)
5 Testing for compliance with technical requirements
5.1 Environmental conditions for testing
The equipment shall be tested under normal test conditions according to the relevant product and basic standards or to
the information accompanying the equipment, which are within the manufacturers declared range of humidity,
temperature and supply voltage. The test conditions shall be recorded in the test report.
5.2 Interpretation of the measurement results
The interpretation of the results recorded in a test report for the measurements described in the present document shall
be as follows:
• the measured value related to the corresponding limit will be used to decide whether an equipment meets the
requirements of the present document;
• the value of the measurement uncertainty for the measurement of each parameter shall be included in the test
report;
• the recorded value of the measurement uncertainty shall be, for each measurement, equal to or less than the
figures in table 1.
For the test methods, according to the present document, the measurement uncertainty figures shall be calculated and
shall correspond to an expansion factor (coverage factor) k = 1,96 or k = 2 (which provide confidence levels of
respectively 95 % and 95,45 % in the case where the distributions characterizing the actual measurement uncertainties
are normal (Gaussian)). Principles for the calculation of measurement uncertainty are contained in ETSI
TR 100 028 [i.2], in particular in annex D of the ETSI TR 100 028-2 [i.3].
Table 1 is based on such expansion factors.
Table 1: Maximum measurement uncertainty
Parameter Uncertainty
Uncertainty in conducted measurements ±1 dB
Uncertainty in radiated measurements ±6 dB

5.3 Methods of measurement
5.3.1 Generic methods of measurement
Two generic methods of measurement are applicable to verifying the performance of the receiving equipment in
question. The conducted test methods shall be used for receivers with an external antenna connector. The radiated test
methods shall be used for all other receivers.
For both generic methods, two generators are needed. One provides the wanted signal, and the other the unwanted
signal, or interferer (when required). The two signals are combined in such a way as to maintain isolation between the
generators. It is necessary to provide calibrated attenuators for control of
...

Draft ETSI EN 303 345-1 V1.1.0 (2018-09)






EUROPEAN STANDARD
Broadcast Sound Receivers;
Part 1: Generic requirements and measuring methods



---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)



Reference
DEN/ERM-TG17-151
Keywords
broadcast, digital, radio, receiver
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2018.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 7
4 Technical requirements specifications . 8
4.1 Environmental profile . 8
4.2 Conformance requirements . 8
4.2.1 Broadcast radio modulation methods . 8
4.2.2 Broadcast radio frequency bands . 8
5 Testing for compliance with technical requirements . 9
5.1 Environmental conditions for testing . 9
5.2 Interpretation of the measurement results . 9
5.3 Methods of measurement . 9
5.3.1 Generic methods of measurement . 9
5.3.2 Generic measurement set-up for radiated testing . 10
5.3.3 Generic measurement set-up for conducted testing . 13
5.3.4 Sensitivity measurement methods . 14
5.3.4.1 Analogue (AM and FM) sensitivity measurements. 14
5.3.4.2 Digital (DAB and DRM) sensitivity measurements . 14
5.3.5 Adjacent channel selectivity and blocking measurement methods . 14
5.3.5.1 Analogue (AM and FM) adjacent channel selectivity and blocking measurements . 14
5.3.5.2 Digital (DAB and DRM) adjacent channel selectivity and blocking measurements . 15
Annex A (informative): A fibre-optic link for receiver testing . 16
Annex B (informative): Measurement set-up for electrical methods during radiated testing . 18
Annex C (informative): Change History . 19
History . 20


ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility
and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 1 of a multi-part deliverable covering the requirements and measuring methods for
broadcast sound receivers to meet the essential requirements of article 3.2 of Directive 2014/53/EU [i.1], as identified
below:
Part 1: "Generic requirements and measuring methods";
Part 2: "AM broadcast sound service";
Part 3: "FM broadcast sound service";
Part 4: "DAB broadcast sound service";
Part 5: "DRM broadcast sound service".
The test data files are contained in archive en_30334501v010100a0.zip which accompanies the present document.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
1 Scope
The present document specifies generic requirements and methods of measurements for devices, including the supplied
antenna, that receive broadcast sound services, whether analogue or digital modulation is used to meet the essential
requirements of article 3.2 of Directive 2014/53/EU [i.1]. Subsequent parts of the present document provide the
necessary test signal configurations and limits for the different broadcast sound services. Multi-function devices may
also fall under the requirements of other documents.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CENELEC EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission
Requirements".
[2] IEC 60315-1 (1988): "Methods of measurement on radio receivers for various classes of emission.
Part 1: General considerations and methods of measurement, including audio-frequency
measurements".
[3] Recommendation ITU-R BS.468-4 (07/1986): "Measurement of audio-frequency noise voltage
level in sound broadcasting".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI TR 100 028 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics".
[i.3] ETSI TR 100 028-2: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 2".
[i.4] ECA table.
NOTE: Available at www.efis.dk.
ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
[i.5] CISPR 35: "Electromagnetic Compatibility of Multimedia equipment - Immunity Requirements".
[i.6] BBC Research & Development White Paper WHP 335: "A Fibre-Optic Link for Use During
Receiver Testing".
NOTE: Available at http://downloads.bbc.co.uk/rd/pubs/whp/whp-pdf-files/WHP335.pdf.
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in Directive 2014/53/EU [i.1] and the
following apply:
adjacent channel selectivity: at a given frequency separation, ratio of the maximum unwanted signal level to the
wanted signal level necessary to provide a given level of audio quality
blocking: at a given frequency separation, ratio of the maximum AM unwanted signal level to the wanted signal level
necessary to provide a given level of audio quality
built-in antenna: antenna that cannot be detached from the equipment
dBm: decibels relative to 1 mW of power
external antenna: antenna designed to be connected to the equipment with the use of a 50 Ω or 75 Ω external
connector
integral antenna: antenna which is detachable from the equipment without the use of any tools, and not using a 50 Ω
or 75 Ω external connector
NOTE: A device that uses a supplied earphone as the antenna has an integral antenna.
sensitivity: minimum wanted signal level required to provide a given level of audio quality
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AM Amplitude Modulation
AMSS Amplitude Modulation Signalling System
BBC British Broadcasting Corporation
BS Broadcast service (Sound)
CISPR Comité International Spécial des Perturbations Radioélectriques
CMAD Common Mode Absorption Device
DAB Digital Audio Broadcasting
DRM Digital Radio Mondiale
EC European Commission
ECA European Common Allocation
EU European Union
FAR Fully Anechoic Room
FM Frequency Modulation
GTEM Gigahertz Transverse ElectroMagnetic
HF High Frequency
IEC International Electrotechnical Commission
ITU-R International Telecommunications Union - Radiocommunications
LED Light Emitting Diode
LF Low Frequency
MF Medium Frequency
RDS Radio Data System
RF Radio Frequency
ETSI

---------------------- Page: 7 ----------------------
8 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
RUT Receiver Under Test
S/PDIF Sony/Philips Digital InterFace
SAC Semi Anechoic Chamber
THD Total Harmonic Distortion
THD+N Total Harmonic Distortion plus Noise
UI User Interface
VHF Very High Frequency
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the manufacturer.
4.2 Conformance requirements
4.2.1 Broadcast radio modulation methods
The following broadcast radio modulation methods are considered feasible within the current authorization regime in
Europe:
• Amplitude modulation, with or without AMSS (AM).
• Frequency modulation, with or without RDS (FM).
• Digital Audio Broadcasting (DAB).
• Digital Radio Mondiale (DRM).
Broadcast radio receivers may include demodulation capability for one or more of these modulation methods.
Conformance shall only be required for each of the modulation methods included in the receiver.
4.2.2 Broadcast radio frequency bands
The following frequency bands are identified in the ECA table [i.4] for broadcast radio services:
• Low frequency (LF): 148,5 kHz to 283,5 kHz.
• Medium frequency (MF): 526,5 kHz to 1 606,5 kHz.
• High Frequency (HF): 3 950 kHz to 4 000 kHz, 5 900 kHz to 6 200 kHz, 7 200 kHz to 7 450 kHz, 9 400 kHz
to 9 900 kHz, 11 600 kHz to 12 100 kHz, 13 570 kHz to 13 870 kHz, 15 100 kHz to 15 800 kHz, 17 480 kHz
to 17 900 kHz, 18 900 kHz to 19 020 kHz, 21 450 kHz to 21 850 kHz and 25 670 kHz to 26 100 kHz.
• VHF band I: 47 MHz to 68 MHz.
• VHF band II: 87,5 MHz to 108 MHz.
• VHF band III: 174 MHz to 240 MHz.
Broadcast radio receivers may include tuning capability for one or more of these frequency bands. Conformance shall
only be required for each of the frequency bands included in the receiver.
ETSI

---------------------- Page: 8 ----------------------
9 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
5 Testing for compliance with technical requirements
5.1 Environmental conditions for testing
The equipment shall be tested under normal test conditions according to the relevant product and basic standards or to
the information accompanying the equipment, which are within the manufacturers declared range of humidity,
temperature and supply voltage. The test conditions shall be recorded in the test report.
5.2 Interpretation of the measurement results
The interpretation of the results recorded in a test report for the measurements described in the present document shall
be as follows:
• the measured value related to the corresponding limit will be used to decide whether an equipment meets the
requirements of the present document;
• the value of the measurement uncertainty for the measurement of each parameter shall be included in the test
report;
• the recorded value of the measurement uncertainty shall be, for each measurement, equal to or less than the
figures in table 1.
For the test methods, according to the present document, the measurement uncertainty figures shall be calculated and
shall correspond to an expansion factor (coverage factor) k = 1,96 or k = 2 (which provide confidence levels of
respectively 95 % and 95,45 % in the case where the distributions characterizing the actual measurement uncertainties
are normal (Gaussian)). Principles for the calculation of measurement uncertainty are contained in ETSI
TR 100 028 [i.2], in particular in annex D of the ETSI TR 100 028-2 [i.3].
Table 1 is based on such expansion factors.
Table 1: Maximum measurement uncertainty
Parameter Uncertainty
Uncertainty in conducted measurements ±1 dB
Uncertainty in radiated measurements ±6 dB

5.3 Methods of measurement
5.3.1 Generic methods of measurement
Two generic methods of measurement are applicable to verifying the performance of the receiving equipment in
question. The conducted test methods shall be used for receivers with an external antenna connector. The radiated test
methods shall be used for all other receivers.
For both generic methods, two generators are needed. One provides the wanted signal, and the other the unwanted
signal, or interferer (when required). The two signals are combined in such a way as to maintain isolation between the
generators. It is necessary to provide calibrated attenuators for control of the individual levels; very often these will be
built into the generators. Where the attenuators are external, cable lengths should be kept short to avoid cross-coupling
effects.
The tests require the audio output of the receiver to be measured. All tonal controls (user operated and
...

SLOVENSKI STANDARD
oSIST prEN 303 345-1 V1.1.0:2018
01-december-2018
5DGLRGLIX]LMVNL]YRþQLVSUHMHPQLNLGHO*HQHULþQH]DKWHYHLQPHULOQHPHWRGH
Broadcast Sound Receivers - Part 1: Generic requirements and measuring methods
Ta slovenski standard je istoveten z: ETSI EN 303 345-1 V1.1.0 (2018-09)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
oSIST prEN 303 345-1 V1.1.0:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 303 345-1 V1.1.0:2018

---------------------- Page: 2 ----------------------
oSIST prEN 303 345-1 V1.1.0:2018
Draft ETSI EN 303 345-1 V1.1.0 (2018-09)






EUROPEAN STANDARD
Broadcast Sound Receivers;
Part 1: Generic requirements and measuring methods



---------------------- Page: 3 ----------------------
oSIST prEN 303 345-1 V1.1.0:2018

2 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)



Reference
DEN/ERM-TG17-151
Keywords
broadcast, digital, radio, receiver
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2018.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------
oSIST prEN 303 345-1 V1.1.0:2018

3 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 7
4 Technical requirements specifications . 8
4.1 Environmental profile . 8
4.2 Conformance requirements . 8
4.2.1 Broadcast radio modulation methods . 8
4.2.2 Broadcast radio frequency bands . 8
5 Testing for compliance with technical requirements . 9
5.1 Environmental conditions for testing . 9
5.2 Interpretation of the measurement results . 9
5.3 Methods of measurement . 9
5.3.1 Generic methods of measurement . 9
5.3.2 Generic measurement set-up for radiated testing . 10
5.3.3 Generic measurement set-up for conducted testing . 13
5.3.4 Sensitivity measurement methods . 14
5.3.4.1 Analogue (AM and FM) sensitivity measurements. 14
5.3.4.2 Digital (DAB and DRM) sensitivity measurements . 14
5.3.5 Adjacent channel selectivity and blocking measurement methods . 14
5.3.5.1 Analogue (AM and FM) adjacent channel selectivity and blocking measurements . 14
5.3.5.2 Digital (DAB and DRM) adjacent channel selectivity and blocking measurements . 15
Annex A (informative): A fibre-optic link for receiver testing . 16
Annex B (informative): Measurement set-up for electrical methods during radiated testing . 18
Annex C (informative): Change History . 19
History . 20


ETSI

---------------------- Page: 5 ----------------------
oSIST prEN 303 345-1 V1.1.0:2018

4 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility
and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 1 of a multi-part deliverable covering the requirements and measuring methods for
broadcast sound receivers to meet the essential requirements of article 3.2 of Directive 2014/53/EU [i.1], as identified
below:
Part 1: "Generic requirements and measuring methods";
Part 2: "AM broadcast sound service";
Part 3: "FM broadcast sound service";
Part 4: "DAB broadcast sound service";
Part 5: "DRM broadcast sound service".
The test data files are contained in archive en_30334501v010100a0.zip which accompanies the present document.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

ETSI

---------------------- Page: 6 ----------------------
oSIST prEN 303 345-1 V1.1.0:2018

5 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 7 ----------------------
oSIST prEN 303 345-1 V1.1.0:2018

6 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
1 Scope
The present document specifies generic requirements and methods of measurements for devices, including the supplied
antenna, that receive broadcast sound services, whether analogue or digital modulation is used to meet the essential
requirements of article 3.2 of Directive 2014/53/EU [i.1]. Subsequent parts of the present document provide the
necessary test signal configurations and limits for the different broadcast sound services. Multi-function devices may
also fall under the requirements of other documents.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CENELEC EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission
Requirements".
[2] IEC 60315-1 (1988): "Methods of measurement on radio receivers for various classes of emission.
Part 1: General considerations and methods of measurement, including audio-frequency
measurements".
[3] Recommendation ITU-R BS.468-4 (07/1986): "Measurement of audio-frequency noise voltage
level in sound broadcasting".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI TR 100 028 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics".
[i.3] ETSI TR 100 028-2: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 2".
[i.4] ECA table.
NOTE: Available at www.efis.dk.
ETSI

---------------------- Page: 8 ----------------------
oSIST prEN 303 345-1 V1.1.0:2018

7 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
[i.5] CISPR 35: "Electromagnetic Compatibility of Multimedia equipment - Immunity Requirements".
[i.6] BBC Research & Development White Paper WHP 335: "A Fibre-Optic Link for Use During
Receiver Testing".
NOTE: Available at http://downloads.bbc.co.uk/rd/pubs/whp/whp-pdf-files/WHP335.pdf.
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in Directive 2014/53/EU [i.1] and the
following apply:
adjacent channel selectivity: at a given frequency separation, ratio of the maximum unwanted signal level to the
wanted signal level necessary to provide a given level of audio quality
blocking: at a given frequency separation, ratio of the maximum AM unwanted signal level to the wanted signal level
necessary to provide a given level of audio quality
built-in antenna: antenna that cannot be detached from the equipment
dBm: decibels relative to 1 mW of power
external antenna: antenna designed to be connected to the equipment with the use of a 50 Ω or 75 Ω external
connector
integral antenna: antenna which is detachable from the equipment without the use of any tools, and not using a 50 Ω
or 75 Ω external connector
NOTE: A device that uses a supplied earphone as the antenna has an integral antenna.
sensitivity: minimum wanted signal level required to provide a given level of audio quality
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AM Amplitude Modulation
AMSS Amplitude Modulation Signalling System
BBC British Broadcasting Corporation
BS Broadcast service (Sound)
CISPR Comité International Spécial des Perturbations Radioélectriques
CMAD Common Mode Absorption Device
DAB Digital Audio Broadcasting
DRM Digital Radio Mondiale
EC European Commission
ECA European Common Allocation
EU European Union
FAR Fully Anechoic Room
FM Frequency Modulation
GTEM Gigahertz Transverse ElectroMagnetic
HF High Frequency
IEC International Electrotechnical Commission
ITU-R International Telecommunications Union - Radiocommunications
LED Light Emitting Diode
LF Low Frequency
MF Medium Frequency
RDS Radio Data System
RF Radio Frequency
ETSI

---------------------- Page: 9 ----------------------
oSIST prEN 303 345-1 V1.1.0:2018

8 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
RUT Receiver Under Test
S/PDIF Sony/Philips Digital InterFace
SAC Semi Anechoic Chamber
THD Total Harmonic Distortion
THD+N Total Harmonic Distortion plus Noise
UI User Interface
VHF Very High Frequency
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the manufacturer.
4.2 Conformance requirements
4.2.1 Broadcast radio modulation methods
The following broadcast radio modulation methods are considered feasible within the current authorization regime in
Europe:
• Amplitude modulation, with or without AMSS (AM).
• Frequency modulation, with or without RDS (FM).
• Digital Audio Broadcasting (DAB).
• Digital Radio Mondiale (DRM).
Broadcast radio receivers may include demodulation capability for one or more of these modulation methods.
Conformance shall only be required for each of the modulation methods included in the receiver.
4.2.2 Broadcast radio frequency bands
The following frequency bands are identified in the ECA table [i.4] for broadcast radio services:
• Low frequency (LF): 148,5 kHz to 283,5 kHz.
• Medium frequency (MF): 526,5 kHz to 1 606,5 kHz.
• High Frequency (HF): 3 950 kHz to 4 000 kHz, 5 900 kHz to 6 200 kHz, 7 200 kHz to 7 450 kHz, 9 400 kHz
to 9 900 kHz, 11 600 kHz to 12 100 kHz, 13 570 kHz to 13 870 kHz, 15 100 kHz to 15 800 kHz, 17 480 kHz
to 17 900 kHz, 18 900 kHz to 19 020 kHz, 21 450 kHz to 21 850 kHz and 25 670 kHz to 26 100 kHz.
• VHF band I: 47 MHz to 68 MHz.
• VHF band II: 87,5 MHz to 108 MHz.
• VHF band III: 174 MHz to 240 MHz.
Broadcast radio receivers may include tuning capability for one or more of these frequency bands. Conformance shall
only be required for each of the frequency bands included in the receiver.
ETSI

---------------------- Page: 10 ----------------------
oSIST prEN 303 345-1 V1.1.0:2018

9 Draft ETSI EN 303 345-1 V1.1.0 (2018-09)
5 Testing for compliance with technical requirements
5.1 Environmental conditions for testing
The equipment shall be tested under normal test conditions according to the relevant product and basic standards or to
the information accompanying the equipment, which are within the manufacturers declared range of humidity,
temperature and supply voltage. The test conditions shall be recorded in the test report.
5.2 Interpretation of the measurement results
The interpretation of the results recorded in a test report for the measurements described in the present document shall
be as follows:
• the measured value related to the corresponding limit will be used to decide whether an equipment meets the
requirements of the present document;
• the value of the measurement uncertainty for the measurement of each parameter shall be included in the test
report;
• the recorded value of the measurement uncertainty shall be, for each measurement, equal to or less than the
figures in table 1.
For the test methods, according to the present document, the measurement uncertainty figures shall be calculated and
shall correspond to an expansion factor (coverage factor) k = 1,96 or k = 2 (which provide confidence levels of
respectively 95 % and 95,45 % in the case where the distributions characterizing the actual measurement uncertainties
are normal (Gaussian)). Principles for the calculation of measurement uncertainty are contained in ETSI
TR 100 028 [i.2], in particular in annex D of the ETSI TR 100 028-2 [i.3].
Table 1 is based on such expansion factors.
Table 1: Maximum measurement uncertainty
Parameter Uncertainty
Uncertainty in conducted measurements ±1 dB
Uncertainty in radiated measurements ±6 dB

5.3 Methods of measurement
5.3.1 Generic methods of measurement
Two generic methods of measurement are applicable to verifying the performance of the receiving equipment in
question. The conducted test methods shall be used for receivers with an external antenna connector. The radiated test
methods shall be used for all other receivers.
For both generic methods, two generators are needed. One provides the wanted signal, and the other the unwanted
signal, or interferer (when required). The two signals are combined in such a way as to maintain isolation between the
generators. It is necessary to provide calibrated attenuators f
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.