Electrical apparatus for the detection of carbon monoxide in domestic premises - Part 2: Electrical apparatus for continuous operation in a fixed installation in recreational vehicles and similar premises including recreational craft - Additional test methods and performance requirements

This document specifies general requirements for the construction, testing and performance of electrically operated carbon monoxide gas detection apparatus, designed for continuous operation in a fixed installation in recreational vehicles and similar premises including recreational craft.
NOTE   For caravan holiday homes EN 50291-1 applies.
This European Standard specifies apparatus designed to operate in the event of an escape of carbon monoxide and to provide a visual and audible alarms only (Type B of EN 50291-1), or to provide visual and audible alarms and an executive action in the form of an output signal that can actuate directly or indirectly a shut-off device and/or other ancillary device (Type A of EN 50291-1).
This European Standard excludes apparatus
-   for the detection of combustible gases, other than carbon monoxide itself (see EN 50194 1),
-   for the detection of CO in industrial installations (see EN 45544-1, EN 45544-2 and EN 45544-3) or commercial premises,
-   for CO measurement for smoke and fire detection.

Elektrische Geräte für die Detektion von Kohlenmonoxid in Wohnhäusern - Teil 2: Ortsfeste elektrische Geräte zum kontinuierlichen Betrieb in Freizeitfahrzeugen und ähnlichen Umgebungen einschließlich Sportbooten - Ergänzende Prüfverfahren und Anforderungen an das Betriebsverhalten

Appareils électriques pour la détection de monoxyde de carbone dans les locaux à usage domestique - Partie 2: Appareils électriques en fonctionnement continu et en installation fixe dans les véhicules de loisir et locaux similaires incluant les embarcations de loisir - Méthodes d'essai supplémentaires et exigences d'aptitude à la fonction

Električne naprave za odkrivanje ogljikovega monoksida v gospodinjstvih - 2. del: Električne naprave za stalno delovanje v nepremičnih inštalacijah na rekreacijskih vozilih in na sorodnih področjih, vključno na rekreacijskih plovilih - Dodatne preskusne metode in zahtevane lastnosti

Ta dokument določa splošne zahteve za sestavo, preskušanje in lastnosti električnih naprav za odkrivanje ogljikovega monoksida, ki so namenjene stalnemu delovanju v nepremičnih inštalacijah na rekreacijskih vozilih in v sorodnih območjih, vključno z rekreacijskimi plovili.
OPOMBA:   Za počitniške prikolice se uporablja standard EN 50291-1.
Ta evropski standard določa naprave, ki so zasnovane za delovanje v primeru uhajanja ogljikovega monoksida ter sprožijo samo vizualni in zvočni alarm (vrsta B iz standarda EN 50291-1) ali vizualni in zvočni alarm ter izvršno dejanje v obliki izhodnega signala, ki lahko neposredno ali posredno sproži napravo za zapiranje plina in/ali drugo pomožno napravo (vrsta A iz standarda EN 50291-1).
Ta evropski standard ne zajema naprav:
–   za zaznavanje gorljivih plinov, razen ogljikovega monoksida (glej standard EN 50194 1);
–   za zaznavanje CO v industrijskih inštalacijah (glej standarde EN 45544-1, EN 45544-2 in EN 45544-3) ali komercialnih objektih;
–   za merjenje CO za zaznavanje dima in ognja.

General Information

Status
Published
Public Enquiry End Date
20-Dec-2018
Publication Date
08-Sep-2019
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
06-Sep-2019
Due Date
11-Nov-2019
Completion Date
09-Sep-2019

Relations

Buy Standard

Standard
EN 50291-2:2019
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 50291-2:2018
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50291-2:2019
01-november-2019
Nadomešča:
SIST EN 50291-2:2010
Električne naprave za odkrivanje ogljikovega monoksida v gospodinjstvih - 2. del:
Električne naprave za stalno delovanje v nepremičnih inštalacijah na rekreacijskih
vozilih in na sorodnih področjih, vključno na rekreacijskih plovilih - Dodatne
preskusne metode in zahtevane lastnosti
Electrical apparatus for the detection of carbon monoxide in domestic premises - Part 2:
Electrical apparatus for continuous operation in a fixed installation in recreational
vehicles and similar premises including recreational craft - Additional test methods and
performance requirements
Elektrische Geräte für die Detektion von Kohlenmonoxid in Wohnhäusern - Teil 2:
Ortsfeste elektrische Geräte zum kontinuierlichen Betrieb in Freizeitfahrzeugen und
ähnlichen Umgebungen einschließlich Sportbooten - Ergänzende Prüfverfahren und
Anforderungen an das Betriebsverhalten
Appareils électriques pour la détection de monoxyde de carbone dans les locaux à
usage domestique - Partie 2: Appareils électriques en fonctionnement continu et en
installation fixe dans les véhicules de loisir et locaux similaires incluant les embarcations
de loisir - Méthodes d'essai supplémentaires et exigences d'aptitude à la fonction
Ta slovenski standard je istoveten z: EN 50291-2:2019
ICS:
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
SIST EN 50291-2:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 50291-2:2019

---------------------- Page: 2 ----------------------
SIST EN 50291-2:2019


EUROPEAN STANDARD EN 50291-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
August 2019
ICS 13.320  Supersedes EN 50291-2:2010 and all of its amendments
and corrigenda (if any)
English Version
Electrical apparatus for the detection of carbon monoxide in
domestic premises - Part 2: Electrical apparatus for continuous
operation in a fixed installation in recreational vehicles and
similar premises including recreational craft - Additional test
methods and performance requirements
Appareils électriques pour la détection de monoxyde de Elektrische Geräte für die Detektion von Kohlenmonoxid in
carbone dans les locaux à usage domestique - Partie 2: Wohnhäusern - Teil 2: Ortsfeste elektrische Geräte zum
Appareils électriques en fonctionnement continu et en kontinuierlichen Betrieb in Freizeitfahrzeugen und ähnlichen
installation fixe dans les véhicules de loisir et locaux Umgebungen einschließlich Sportbooten - Ergänzende
similaires incluant les embarcations de loisir - Méthodes Prüfverfahren und Anforderungen an das Betriebsverhalten
d'essai supplémentaires et exigences d'aptitude à la
fonction
This European Standard was approved by CENELEC on 2019-04-26. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Republic of North Macedonia, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 50291-2:2019 E

---------------------- Page: 3 ----------------------
SIST EN 50291-2:2019
EN 50291-2:2019 (E)
European foreword
This document (EN 50291-2:2019) has been prepared by CLC/TC 216 "Gas detectors".
The following dates are fixed:
• latest date by which this document has to be (dop) 2020-04-26
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2022-04-26
conflicting with this document have to be
withdrawn

This document supersedes EN 50291-2:2010 and all of its amendments and corrigenda (if any).
This Part 2 is to be used in conjunction with EN 50291-1:2018.
This Part 2 supplements or modifies the corresponding clauses of EN 50291-1:2018. Where this Part 2 states
"addition", "modification" or "replacement", the relevant text of Part 1 is to be adapted accordingly.
2

---------------------- Page: 4 ----------------------
SIST EN 50291-2:2019
EN 50291-2:2019 (E)
1 Scope
This document specifies general requirements for the construction, testing and performance of electrically operated
carbon monoxide gas detection apparatus, designed for continuous operation in a fixed installation in recreational
vehicles and similar premises including recreational craft.
NOTE For caravan holiday homes EN 50291-1 applies.
This document specifies apparatus designed to operate in the event of an escape of carbon monoxide and to
provide a visual and audible alarms only (Type B of EN 50291-1), or to provide visual and audible alarms and an
executive action in the form of an output signal that can actuate directly or indirectly a shut-off device and/or other
ancillary device (Type A of EN 50291-1).
This document excludes apparatus
— for the detection of combustible gases, other than carbon monoxide itself (see EN 50194-1),
— for the detection of CO in industrial installations (see EN 45544-1, EN 45544-2 and EN 45544-3) or
commercial premises,
— for CO measurement for smoke and fire detection.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references, the
latest edition of the referenced document (including any amendments) applies.
EN 50270:2015, Electromagnetic compatibility — Electrical apparatus for the detection and measurement of
combustible gases, toxic gases or oxygen
EN 50291-1:2018, Gas detectors — Electrical apparatus for the detection of carbon monoxide in domestic
premises — Part 1: Test methods and performance requirements
EN 60068-2-6, Environmental testing — Part 2-6: Tests — Test Fc: Vibration (sinusoidal) (IEC 60068-2-6)
EN 60068-2-7, Environmental testing — Part 2: Tests — Test Ga: Acceleration, steady state (IEC 60068-2-7)
EN 60068-2-27, Environmental testing — Part 2-27: Tests — Test Ea and guidance: Shock (IEC 60068-2-27)
EN 60529:1991, Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989)
EN 60721-3-6:1993, Classification of environmental conditions — Part 3: Classification of groups of environmental
parameters and their severities — Section 6: Ship environment (IEC 60721-3-6:1987)
EN 60945:2002, Maritime navigation and radiocommunication equipment and systems — General requirements —
Methods of testing and required test results (IEC 60945:2002)
ISO 7637-2:2011, Road vehicles — Electrical disturbances from conduction and coupling — Part 2: Electrical
transient conduction along supply lines only
3

---------------------- Page: 5 ----------------------
SIST EN 50291-2:2019
EN 50291-2:2019 (E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 50291-1 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1
recreational vehicle
recreational vehicles considered by this European Standard include recreational craft, caravans and motor
caravans
Note 1 to entry: Other motorised vehicles like trucks are known to have residential accommodation. They are not recreational
vehicles but are considered as similar premises in respect of this European Standard.
3.2
recreational craft
boat of a minimum length of 2,5 m and a maximum length of 24 m as specified in Directive 2013/53/EU, which is
intended for sports or leisure purposes
Note 1 to entry: For the purposes of this European Standard the word ´boat´ should be taken with the meaning ´recreational
craft´.
3.3
remote sensor
sensor assembly that is mounted in a separate location from the control unit
Note 1 to entry: This definition should be read in conjunction with EN 50291-1:2018, Definition 3.5.
3.4
control unit
unit that may contain the power supply, signal processing, alarm circuits and indicators
3.5
vehicle supply powered apparatus
apparatus designed to be powered by the vehicle’s electrical supply
3.6
caravan
trailer leisure accommodation vehicle that meets requirements for construction and use of road vehicles
[SOURCE: EN 13878:2003]
3.7
motor caravan
self-propelled leisure accommodation vehicle that meets requirements for construction and use of road vehicles
It contains at least
– seats and table,
– sleeping accommodation which may be converted from the seats,
– cooking facilities, and
– storage facilities
[SOURCE: EN 13878:2003]
4

---------------------- Page: 6 ----------------------
SIST EN 50291-2:2019
EN 50291-2:2019 (E)
3.8
caravan holiday home
transportable leisure accommodation vehicle that does not meet requirements for construction and use of road
vehicles, that retains means for mobility and that is for temporary or seasonal occupation
[SOURCE: EN 13878:2003]
4 Symbols and abbreviations
This sub-clause of EN 50291-1 is applicable.
5 Design requirements
5.1 General requirements
This sub-clause of EN 50291-1 is applicable, with the following addition:
In this European Standard there are requirements that cover all apparatus. Additional application specific
requirements apply to certain groups of recreational vehicles, such as boats. An apparatus which complies with the
requirements for recreational craft will automatically comply with the requirements for motor caravans and
caravans. An apparatus which complies with the requirements for motor caravans will automatically comply with the
requirements for caravans. The apparatus are designed for continuous operation.
NOTE 1 When the vehicle is not in use the apparatus may be switched off in order to save the vehicle’s power supply or the
internal batteries.
The apparatus may consist of one or more sensor(s) and a control unit. Sensors (integrated into the apparatus or
remote) shall be designed to detect carbon monoxide.
NOTE 2 Sensors or apparatus designed according EN 50291-1 may be used as apparatus or as component of it, if the
additional requirements of this European Standard are complied with.
The apparatus shall reliably detect the presence of carbon monoxide in recreational vehicles under the stated
application conditions, shall produce an alarm and Type A apparatus shall be able to initiate executive actions
whenever the level exceeds the alarm set point.
The apparatus, electrical assemblies and components shall comply with EN 50291-1, where applicable, with the
construction requirements of 5.2 and the test and performance requirements of Clause 6.
5.2 Construction
This sub-clause of EN 50291-1 is applicable, with the following addition:
Each sensor shall be constructed of materials that will not corrode in the environment where it is designed for, e.g.
in the presence of a salt-laden atmosphere as exists in a marine environment, or be affected by the gases and
vapours that may be expected to be present in a recreational craft.
Adequate means shall be provided to mount the remote sensor(s), pointing vertically downwards, securely to the
vehicle’s substructure.
The control unit shall be constructed of materials that are suitable for use in the intended application e.g. in the
cabin or below deck area of a recreational craft.
5.4 Alarms
This sub-clause of EN 50291-1 is applicable, with the following addition:
5.4.4 Addition:
If more than one sensor is connected to a control unit, the control unit shall indicate the alarm condition of the
different sensors individually.
5

---------------------- Page: 7 ----------------------
SIST EN 50291-2:2019
EN 50291-2:2019 (E)
5.6 Fault Warnings
This sub-clause of EN 50291-1 is replaced by:
The apparatus shall provide a visual and audible fault signal in the event of interruption of communication between
control unit and the remote sensor(s).
The audible fault signal shall be clearly identified and different from a gas alarm.
5.9 Transmittable output signal (applicable for type A apparatus only)
This sub-clause of EN 50291-1 is applicable, with the following addition:
The output signal of the apparatus shall operate under the same c
...

SLOVENSKI STANDARD
oSIST prEN 50291-2:2018
01-december-2018
(OHNWULþQHQDSUDYH]DRGNULYDQMHRJOMLNRYHJDPRQRNVLGDYJRVSRGLQMVWYLKGHO
(OHNWULþQHQDSUDYH]DVWDOQRGHORYDQMHYQHSUHPLþQLKLQãWDODFLMDKQDUHNUHDFLMVNLK
YR]LOLKLQQDVRURGQLKSRGURþMLKYNOMXþQRQDUHNUHDFLMVNLKSORYLOLK'RGDWQH
SUHVNXVQHPHWRGHLQ]DKWHYDQHODVWQRVWL
Electrical apparatus for the detection of carbon monoxide in domestic premises - Part 2:
Electrical apparatus for continuous operation in a fixed installation in recreational
vehicles and similar premises including recreational craft - Additional test methods and
performance requirements
Elektrische Geräte für die Detektion von Kohlenmonoxid in Wohnhäusern - Teil 2:
Ortsfeste elektrische Geräte zum kontinuierlichen Betrieb in Freizeitfahrzeugen und
ähnlichen Umgebungen einschließlich Sportbooten - Ergänzende Prüfverfahren und
Anforderungen an das Betriebsverhalten
Appareils électriques pour la détection de monoxyde de carbone dans les locaux à
usage domestique - Partie 2: Appareils électriques en fonctionnement continu et en
installation fixe dans les véhicules de loisir et locaux similaires incluant les embarcations
de loisir - Méthodes d'essai supplémentaires et exigences d'aptitude à la fonction
Ta slovenski standard je istoveten z: prEN 50291-2
ICS:
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
oSIST prEN 50291-2:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 50291-2:2018

---------------------- Page: 2 ----------------------
oSIST prEN 50291-2:2018


EUROPEAN STANDARD DRAFT
prEN 50291-2
NORME EUROPÉENNE

EUROPÄISCHE NORM

September 2018
ICS 13.320 Will supersede EN 50291-2:2010
English Version
Electrical apparatus for the detection of carbon monoxide in
domestic premises - Part 2: Electrical apparatus for continuous
operation in a fixed installation in recreational vehicles and
similar premises including recreational craft - Additional test
methods and performance requirements
Appareils électriques pour la détection de monoxyde de Elektrische Geräte für die Detektion von Kohlenmonoxid in
carbone dans les locaux à usage domestique - Partie 2: Wohnhäusern - Teil 2: Ortsfeste elektrische Geräte zum
Appareils électriques en fonctionnement continu et en kontinuierlichen Betrieb in Freizeitfahrzeugen und ähnlichen
installation fixe dans les véhicules de loisir et locaux Umgebungen einschließlich Sportbooten - Ergänzende
similaires incluant les embarcations de loisir - Méthodes Prüfverfahren und Anforderungen an das Betriebsverhalten
d'essai supplémentaires et exigences d'aptitude à la
fonction
This draft European Standard is submitted to CENELEC members for enquiry.
Deadline for CENELEC: 2018-12-21.

It has been drawn up by CLC/TC 216.

If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 66312 Ref. No. prEN 50291-2 E

---------------------- Page: 3 ----------------------
oSIST prEN 50291-2:2018
prEN 50291-2:2018 (E)
1 European foreword
2 This document (prEN 50291-2:2018) has been prepared by CLC/TC 216 "Gas detectors".
3 This document is currently submitted to the Enquiry.
4 The following dates are proposed:
• latest date by which the existence of this (doa) dor + 6 months
document has to be announced at national
level
• latest date by which this document has to be (dop) dor + 12 months
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) dor + 36 months
conflicting with this document have to be (to be confirmed or
withdrawn modified when voting)
5 This document will supersede EN 50291-2:2010.
6 This Part 2 is to be used in conjunction with EN 50291-1:2018.
7 This Part 2 supplements or modifies the corresponding clauses of EN 50291-1:2018. Where this Part 2 states
8 "addition", "modification" or "replacement", the relevant text of Part 1 is to be adapted accordingly.
2

---------------------- Page: 4 ----------------------
oSIST prEN 50291-2:2018
prEN 50291-2:2018 (E)
9 1 Scope
10 This document specifies general requirements for the construction, testing and performance of electrically operated
11 carbon monoxide gas detection apparatus, designed for continuous operation in a fixed installation in recreational
12 vehicles and similar premises including recreational craft.
13 NOTE For caravan holiday homes EN 50291-1 applies.
14 This European Standard specifies apparatus designed to operate in the event of an escape of carbon monoxide
15 and to provide a visual and audible alarms only (Type B of EN 50291-1), or to provide visual and audible alarms
16 and an executive action in the form of an output signal that can actuate directly or indirectly a shut-off device and/or
17 other ancillary device (Type A of EN 50291-1).
18 This European Standard excludes apparatus
19 — for the detection of combustible gases, other than carbon monoxide itself (see EN 50194-1),
20 — for the detection of CO in industrial installations (see EN 45544-1, EN 45544-2 and EN 45544-3) or
21 commercial premises,
22 — for CO measurement for smoke and fire detection.
23 2 Normative references
24 The following documents are referred to in the text in such a way that some or all of their content constitutes
25 requirements of this document. For dated references, only the edition cited applies. For undated references, the
26 latest edition of the referenced document (including any amendments) applies.
27 EN 50270:2015, Electromagnetic compatibility — Electrical apparatus for the detection and measurement of
28 combustible gases, toxic gases or oxygen
29 EN 50291-1:2018, Gas detectors — Electrical apparatus for the detection of carbon monoxide in domestic
30 premises — Part 1: Test methods and performance requirements
31 EN 60068-2-6, Environmental testing — Part 2-6: Tests — Test Fc: Vibration (sinusoidal) (IEC 60068-2-6)
32 EN 60068-2-7, Environmental testing — Part 2: Tests — Test Ga: Acceleration, steady state (IEC 60068-2-7)
33 EN 60068-2-27, Environmental testing — Part 2-27: Tests — Test Ea and guidance: Shock (IEC 60068-2-27)
34 EN 60529:1991, Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989)
35 EN 60721-3-6:1993, Classification of environmental conditions — Part 3: Classification of groups of environmental
36 parameters and their severities — Section 6: Ship environment (IEC 60721-3-6:1987)
37 EN 60945:2002, Maritime navigation and radiocommunication equipment and systems — General requirements —
38 Methods of testing and required test results (IEC 60945:2002)
39 ISO 7637-2:2011, Road vehicles — Electrical disturbances from conduction and coupling — Part 2: Electrical
40 transient conduction along supply lines only
41 3 Terms and definitions
42 For the purposes of this document, the terms and definitions given in EN 50291-1 and the following apply.
43 ISO and IEC maintain terminological databases for use in standardization at the following addresses:
44 — IEC Electropedia: available at http://www.electropedia.org/
45 — ISO Online browsing platform: available at http://www.iso.org/obp
3

---------------------- Page: 5 ----------------------
oSIST prEN 50291-2:2018
prEN 50291-2:2018 (E)
46 3.1
47 recreational vehicle
48 recreational vehicles considered by this European Standard include recreational craft, caravans and motor
49 caravans
50 Note 1 to entry: Other motorised vehicles like trucks are known to have residential accommodation. They are not recreational
51 vehicles but are considered as similar premises in respect of this European Standard.
52 3.2
53 recreational craft
54 boat of a minimum length of 2,5 m and a maximum length of 24 m as specified in Directive 2013/53/EU, which is
55 intended for sports or leisure purposes
56 Note 1 to entry: For the purposes of this European Standard the word ´boat´ should be taken with the meaning ´recreational
57 craft´.
58 3.3
59 remote sensor
60 sensor assembly that is mounted in a separate location from the control unit
61 Note 1 to entry: This definition should be read in conjunction with EN 50291-1:2018, Definition 3.5.
62 3.4
63 control unit
64 unit that may contain the power supply, signal processing, alarm circuits and indicators
65 3.5
66 vehicle supply powered apparatus
67 apparatus designed to be powered by the vehicle’s electrical supply
68 3.6
69 caravan
70 trailer leisure accommodation vehicle that meets requirements for construction and use of road vehicles
71 [SOURCE: EN 13878:2003]
72 3.7
73 motor caravan
74 self-propelled leisure accommodation vehicle that meets requirements for construction and use of road vehicles
75 It contains at least
76 – seats and table,
77 – sleeping accommodation which may be converted from the seats,
78 – cooking facilities, and
79 – storage facilities
80 [SOURCE: EN 13878:2003]
81 3.8
82 caravan holiday home
83 transportable leisure accommodation vehicle that does not meet requirements for construction and use of road
84 vehicles, that retains means for mobility and that is for temporary or seasonal occupation
85 [SOURCE: EN 13878:2003]
4

---------------------- Page: 6 ----------------------
oSIST prEN 50291-2:2018
prEN 50291-2:2018 (E)
86 4 Symbols and abbreviations
87 This sub-clause of EN 50291-1 is applicable.
88 5 Design requirements
89 5.1 General requirements
90 This sub-clause of EN 50291-1 is applicable, with the following addition:
91 In this European Standard there are requirements that cover all apparatus. Additional application specific
92 requirements apply to certain groups of recreational vehicles, such as boats. An apparatus which complies with the
93 requirements for recreational craft will automatically comply with the requirements for motor caravans and
94 caravans. An apparatus which complies with the requirements for motor caravans will automatically comply with the
95 requirements for caravans. The apparatus are designed for continuous operation.
96 NOTE 1 When the vehicle is not in use the apparatus may be switched off in order to save the vehicle’s power supply or the
97 internal batteries.
98 The apparatus may consist of one or more sensor(s) and a control unit. Sensors (integrated into the apparatus or
99 remote) shall be designed to detect carbon monoxide.
100 NOTE 2 Sensors or apparatus designed according EN 50291-1 may be used as apparatus or as component of it, if the
101 additional requirements of this European Standard are complied with.
102 The apparatus shall reliably detect the presence of carbon monoxide in recreational vehicles under the stated
103 application conditions, shall produce an alarm and Type A apparatus shall be able to initiate executive actions
104 whenever the level exceeds the alarm set point.
105 The apparatus, electrical assemblies and components shall comply with EN 50291-1, where applicable, with the
106 construction requirements of 5.2 and the test and performance requirements of Clause 6.
107 5.2 Construction
108 This sub-clause of EN 50291-1 is applicable, with the following addition:
109 Each sensor shall be constructed of materials that will not corrode in the environment where it is designed for, e.g.
110 in the presence of a salt-laden atmosphere as exists in a marine environment, or be affected by the gases and
111 vapours that may be expected to be present in a recreational craft.
112 Adequate means shall be provided to mount the remote sensor(s), pointing vertically downwards, securely to the
113 vehicle’s substructure.
114 The control unit shall be constructed of materials that are suitable for use in the intended application e.g. in the
115 cabin or below deck area of a recreational craft.
116 5.4 Alarms
117 This sub-clause of EN 50291-1 is applicable, with the following addition:
118 5.4.4 Addition:
119 If more than one sensor is connected to a control unit, the control unit shall indicate the alarm condition of the
120 different sensors individually.
121 5.6 Fault Warnings
122 This sub-clause of EN 50291-1 is replaced by:
123 The apparatus shall provide a visual and audible fault signal in the event of interruption of communication between
124 control unit and the remote sensor(s).
125 The audible fault signal shall be clearly identified and different from a gas alarm.
126 5.9 Transmittable output signal (applicable for type A apparatus only)
127 This sub-clause of EN 50291-1 is applicable, with the following addition:
5

---------------------- Page: 7 --
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.