SIST EN 50318:2019/oprAA:2021
(Amendment)Railway applications - Current collection systems - Validation of simulation of the dynamic interaction between pantograph and overhead contact line
Railway applications - Current collection systems - Validation of simulation of the dynamic interaction between pantograph and overhead contact line
Simulation techniques are used to assess the dynamic interaction between overhead contact lines and pantographs, as part of the prediction of current collection quality. This document specifies functional requirements for the validation of such simulation methods to ensure confidence in, and mutual acceptance of the results of the simulations.
This document deals with:
- input and output parameters of the simulation;
- comparison with line test measurements, and the characteristics of those line tests;
- validation of pantograph models;
- comparison between different simulation methods;
- limits of application of validated methods to assessments of pantographs and overhead contact lines.
This document applies to the current collection from an overhead contact line by pantographs mounted on railway vehicles. It does not apply to trolley bus systems.
Bahnanwendungen - Stromabnahmesysteme - Validierung von Simulationssystemen für das dynamische Zusammenwirken zwischen Dachstromabnehmer und Oberleitung
Applications ferroviaires - Systèmes de captage de courant - Validation des simulations de l'interaction dynamique entre le pantographe et la caténaire
Železniške naprave - Sistemi tokovnega odjema - Veljavnost simuliranja medsebojnih dinamičnih vplivov med tokovnim odjemnikom in kontaktnim vodnikom
General Information
RELATIONS
Standards Content (sample)
SLOVENSKI STANDARD
SIST EN 50318:2019/oprAA:2021
01-marec-2021
Železniške naprave - Sistemi tokovnega odjema - Veljavnost simuliranja
medsebojnih dinamičnih vplivov med tokovnim odjemnikom in kontaktnim
vodnikom
Railway applications - Current collection systems - Validation of simulation of the
dynamic interaction between pantograph and overhead contact lineBahnanwendungen - Stromabnahmesysteme - Validierung von Simulationssystemen für
das dynamische Zusammenwirken zwischen Dachstromabnehmer und Oberleitung
Applications ferroviaires - Systèmes de captage de courant - Validation des simulations
de l'interaction dynamique entre le pantographe et la caténaireTa slovenski standard je istoveten z: EN 50318:2018/prAA:2020
ICS:
29.280 Električna vlečna oprema Electric traction equipment
SIST EN 50318:2019/oprAA:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------SIST EN 50318:2019/oprAA:2021
---------------------- Page: 2 ----------------------
SIST EN 50318:2019/oprAA:2021
EUROPEAN STANDARD DRAFT
EN 50318:2018
NORME EUROPÉENNE
EUROPÄISCHE NORM
prAA
December 2020
ICS
English Version
Railway applications - Current collection systems - Validation of
simulation of the dynamic interaction between pantograph and
overhead contact line
Applications ferroviaires - Systèmes de captage de courant Bahnanwendungen - Stromabnahmesysteme - Validierung
- Validation des simulations de l'interaction dynamique von Simulationssystemen für das dynamische
entre le pantographe et la caténaire Zusammenwirken zwischen Dachstromabnehmer und
OberleitungThis draft amendment prAA, if approved, will modify the European Standard EN 50318:2018; it is submitted to CENELEC members for
enquiry.Deadline for CENELEC: 2021-03-12.
It has been drawn up by CLC/SC 9XC.
If this draft becomes an amendment, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.
This draft amendment was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 71562 Ref. No. EN 50318:2018/prAA:2020 E---------------------- Page: 3 ----------------------
SIST EN 50318:2019/oprAA:2021
EN 50318:2018/prAA:2020 (E)
Contents Page
European foreword ............................................................................................................................. 4
1 Modification to the whole standard ..................................................................................... 5
2 Modification to 3.6, standard deviation ............................................................................... 5
3 Modification to 3.15, transfer function < of a pantograph >.............................................. 5
4 Modification to 3.21, wave propagation speed of the contact wire .................................. 5
5 Modification to 3.25, dynamic interaction ........................................................................... 5
6 Modification to Clause 4, Symbols and abbreviations ...................................................... 5
7 Modification to 6.1, General requirements ......................................................................... 5
8 Modification to 6.2.1, General .............................................................................................. 5
9 Modification to 6.2.2, Mass – spring – damper – models (lumped parameter models) . 5
10 Modification to 6.2.3, Multi-body models ............................................................................ 6
11 Modification to 6.3, Validation of pantograph models ....................................................... 6
12 Modification to 7.1, General requirements ......................................................................... 6
13 Modification to 7.2, Data requirements ............................................................................... 6
14 Modification to 9.3, Contact wire displacement ................................................................. 6
15 Modification to 10.3.2, Deviations of pantograph characteristics .................................... 6
16 Modification to 10.3.3, Deviations of overhead contact line parameters ........................ 6
17 Modification to 10.3.4, Deviations of simulation parameters............................................ 6
18 Modification to 11.4, Reference model results ................................................................... 6
19 Modification to A.2.2, Special data for the contact line reference model - AC –
Simple ..................................................................................................................................... 6
20 Modification to A.2.3, Special data for the reference model of contact line AC – Stitched
................................................................................................................................................. 6
21 Modification to A.2.4, Special data for the reference model of contact line DC –
simple ..................................................................................................................................... 7
22 Modification to B.1, Measurement results of simple AC high speed contact line .......... 7
23 Modification to B.1.1.2, Parameters of simulation ............................................................. 7
24 Modification to B.1.1.3, Model parameter and mechanical data of OCL .......................... 7
25 Modification to B.1.1.4, Geometrical data of overhead contact line ................................ 7
26 Modification to B.1.1.6, Support definition ......................................................................... 8
27 Modification to B.1.1.7.3, Tension length 3 (first and last span without any droppers,
with a Support S on each side) .......................................................................................... 10
28 Modification to B.1;2, Pantograph model ......................................................................... 10
29 Modification to B.2, Measurement results of a stitched AC high speed contact line .. 10
30 Modification to B.2.2.1, Parameters of simulation ........................................................... 10
31 Modification to B.2.2.3, Geometrical data of overhead contact line .............................. 11
32 Modification to B.2.2.3, Geometrical data of overhead contact line .............................. 11
33 Modification to B.2.2.4, Support data ................................................................................ 11
---------------------- Page: 4 ----------------------SIST EN 50318:2019/oprAA:2021
EN 50318:2018/prAA:2020 (E)
34 Modification to B.2.3 Pantograph data .............................................................................. 11
35 Modification to B.2.4, Calculated and measured data of OCL-rest position for validation
............................................................................................................................................... 11
36 Modification to B.3.2.1, Parameters of simulation ........................................................... 11
37 Modification to B.3.2.3, Geometrical data of overhead contact line .............................. 11
38 Modification to B.3.2.3, Geometrical data of overhead contact line .............................. 12
39 Modification to B.3.2.4, Support data ................................................................................ 12
40 Modification to B.3.3, Pantograph data ............................................................................. 12
41 Modification to Annex C, Relation to TSI assessment process ..................................... 13
42 Modification to Annex ZZ, Relationship between this European standard and theessential requirements of EU Directive 2008/57/EC [2008 OJ L191] aimed to be covered
............................................................................................................................................... 16
---------------------- Page: 5 ----------------------SIST EN 50318:2019/oprAA:2021
EN 50318:2018/prAA:2020 (E)
European foreword
This document (EN 50318:2018/prAA:2020) has been prepared by SC 9XC, Electric supply and earthing
systems for public transport equipment and ancillary apparatus (fixed installations), of Technical Committee
CENELEC TC 9X, Electrical and electronic applications for railways.This document is currently submitted to the Enquiry.
The following dates are proposed:
• latest date by which the existence of this (doa) dor + 6 months
document has to be announced at national
level
• latest date by which this document has to be (dop) dor + 12 months
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) dor + 36 months
conflicting with this document have to be (to be confirmed or
withdrawn modified when voting)
This document has been prepared under a mandate given to CENELEC by the European Commission and
the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.---------------------- Page: 6 ----------------------
SIST EN 50318:2019/oprAA:2021
EN 50318:2018/prAA:2020 (E)
1 Modification to the whole standard
Replace “LOC&PAS TSI” by “TSI LOC & PAS”
Replace “ENE TSI” by “TSI ENE”
Replace “contact line” by “overhead contact line”.
Replace “messenger (wire)” by “catenary (wire)”
2 Modification to 3.6, standard deviation
After the term “standard deviation” add the specific use between angle brackets “”
3 Modification to 3.15, transfer function < of a pantograph >Replace the first paragraph by “ratio of an applied input on pantograph head to the response of the
pantograph, depending on frequency”4 Modification to 3.21, wave propagation speed of the contact wire
Replace the title of 3.21 by “wave propagation velocity ”
5 Modification to 3.25, dynamic interaction
Replace the first paragraph by “behaviour between pantograph(s) and overhead contact line when in
contact, described by contact forces and vertical displacements of contact point(s)”
6 Modification to Clause 4, Symbols and abbreviationsAdd under the fourth line of the subclause “Abbreviations”:
“FFT fast Fourier transformation”
Add under the 9 line of the subclause “Abbreviations”:
“ROCL rigid overhead contact line”
7 Modification to 6.1, General requirements
Replace the last paragraph by “Aerodynamic effects on the pantograph shall as a minimum be considered
by adjusting the mean contact force as a function of speed.”8 Modification to 6.2.1, General
Replace the word “operation height” in the second paragraph by “contact wire height”
Replace the word “operation height” under the subclause NOTE by “contact wire height”
9 Modification to 6.2.2, Mass – spring – damper – models (lumped parametermodels)
Replace the second bullet point by
“— stiffness characteristics of joints connecting the discrete masses, including any nonlinearity (if
applicable)”;Replace the third bullet point by:
“— damping characteristics of joints connecting the discrete masses, including any nonlinearity (if
applicable)”;---------------------- Page: 7 ----------------------
SIST EN 50318:2019/oprAA:2021
EN 50318:2018/prAA:2020 (E)
Replace the last bullet point by the following sentence by (write as sentence and not as a bullet point): “The
aerodynamic forces will be applied through a coefficient to every mass in order to apply an additional
aerodynamic effort to the static effort.”10 Modification to 6.2.3, Multi-body models
Replace the first paragraph by “For multi-body models, additional to that described in 6.2.2, the following
input is required”:11 Modification to 6.3, Validation of pantograph models
Replace the 13th paragraph by “For the calculation of Q, the frequencies with a measured apparent mass
below 2 kg shall be excluded.”12 Modification to 7.1, General requirements
Replace the third paragraph by “ROCL have very small vertical displacements in operation. The validation
of these models and interaction simulations is only possible for the contact force in direct comparison with
the measured results.”13 Modification to 7.2, Data requirements
Replace the text of the first bullet point by “length of each span, or distance between supports”;
14 Modification to 9.3, Contact wire displacementReplace the paragraph after the bullet point by “The time history of the vertical position of the contact wire
at any specified point shall be available for output.”15 Modification to 10.3.2, Deviations of pantograph characteristics
Replace the title of 10.3.2 by “10.3.2 Permissible changes of pantograph characteristics”
16 Modification to 10.3.3, Deviations of overhead contact line parametersReplace the title of 10.3.3 by “10.3.3 Permissible changes of overhead contact line parameters”
17 Modification to 10.3.4, Deviations of simulation parametersReplace the title of 10.3.4 by “10.3.4 Permissible changes of simulation parameters”
18 Modification to 11.4, Reference model resultsReplace the third paragraph by “Simulation results shall be filtered in the frequency domain with the defined
cut off frequencies.”19 Modification to A.2.2, Special data for the contact line reference model - AC –
SimpleReplace the first paragraph by “The overhead contact line is defined by a simple catenary equipment with
a single contact wire according to Figure A.1.”20 Modification to A.2.3, Special data for the reference model of contact line AC –
StitchedReplace the first paragraph by “The overhead contact line is defined by a simple catenary equipment with
a single contact wire and stitched catenary suspensions according to Figure A.2.”
---------------------- Page: 8 ----------------------SIST EN 50318:2019/oprAA:2021
EN 50318:2018/prAA:2020 (E)
21 Modification to A.2.4, Special data for the reference model of contact line DC –
simpleReplace the first sentence in the first paragraph by “The overhead contact line is defined by a simple
catenary equipment with twin contact wires (two contact wires suspended from a single catenary wire).”
22 Modification to B.1, Measurement results of simple AC high speed contact lineReplace the title by “B.1 Measurement results of simple AC high speed overhead contact line”
23 Modification to B.1.1.2, Parameters of simulationReplace the first sentence of the last paragraph by “The overhead contact line is defined by a simple
catenary equipment with a single contact wire and a single catenary wire.”24 Modification to B.1.1.3, Model parameter and mechanical data of OCL
In Table B.1, replace “EI” as symbol for Young’s Modulus by “E”
25 Modification to B.1.1.4, Geometrical data of overhead contact line
Replace the first sentence of the first paragraph by “The overhead contact line is defined by a simple
catenary equipment with a single contact wire and a single catenary wire on straight track.”
---------------------- Page: 9 ----------------------SIST EN 50318:2019/oprAA:2021
EN 50318:2018/prAA:2020 (E)
26 Modification to B.1.1.6, Support definition
Replace Table B.8 by the following
Table B.8 — Support definition of tension length 1
Support
1 2 3 4 5 6 7 8 9 10
number
Cumulative 222,7 267,7 312,7 357,7 402,7
0,00 42,25 86,95 132,25 177,75
position [m] 5 5 5 5 5
CW height [m] 6,35 5,63 5,08 5,08 5,08 5,08 5,08 5,08 5,08 5,08
MW height [m] 6,85 6,88 7,08 6,48 6,48 6,48 6,48 6,48 6,48 6,48
CW stagger [m] 0 0,65 0,3 −0,25 0,1 −0,2 0,1 −0,2 0,1 −0,2
MW stagger [m] 0 0,65 0,3 −0,25 0,1 −0,2 0,1 −0,2 0,1 −0,2
Support
11 12 13 14 15 16 17 18 19 20
number
Cumulative 452,2 501,7 699,7 749,2 798,7 848,2 897,7
551,25 600,75 650,25
position [m] 5 5 5 5 5 5 5
CW height [m] 5,08 5,08 5,08 5,08 5,08 5,08 5,08 5,08 5,08 5,08
MW height [m] 6,48 6,48 6,48 6,48 6,48 6,48 6,48 6,48 6,48 6,48
CW stagger [m] 0,1 −0,2 0,1 −0,2 0,1 −0,2 0,1 −0,2 0,1 −0,2
MW stagger [m] 0,1 −0,2 0,1 −0,2 0,1 −0,2 0,1 −0,2 0,1 −0,2
Support
21 22 23 24 25
number
Cumulative 947,2 997,2 1047,0 1096,2 1145,2
position [m] 5 5 5 5 5
CW height [m] 5,08 5,08 5,08 5,63 6,35
MW height [m] 6,48 6,48 7,08 6,88 6,85
CW stagger [m] 0,2 −0,15 0,1 0,35 0
MW stagger
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.