Aerospace series - Plug, protective, non-metallic, for EN 6123 fitting ends

This document specifies the dimensions, tolerances and required characteristics of protective plugs, non metallic, for EN 6123 fitting ends to seal fluid ports during transportation and storage in order to prevent:
- contamination by moisture, fluids, chemicals and particles;
- spillage inside package or aircraft section;
- port and pipe end damages;
- port and pipe clogging due to plug ingestion.
Because of the cleanliness requirements, parts shall only be used once.

Luft- und Raumfahrt - Stopfen, nicht metallisch, zum Schutz für Endfittinge nach EN 6123

In diesem Dokument werden die Maße, Toleranzen und erforderlichen Kennwerte von nichtmetallischen Stopfen zum Schutz für Endfittinge nach EN 6123 festgelegt, mit denen Fluidanschlüsse während des Transports und der Aufbewahrung verschlossen werden, um Folgendes zu verhindern:
- Verunreinigung durch Feuchtigkeit, Fluide, Chemikalien und Partikel;
- Leckage innerhalb der Verpackung oder einer Luftfahrzeugsektion;
- Beschädigung an Anschlüssen und Rohrenden; und
- Verstopfung von Anschlüssen und Rohren aufgrund des Ansaugens von Stopfen.
Wegen der Reinheitsanforderungen dürfen die Teile stets nur einmal verwendet werden.

Série aérospatiale - Prise, protectrice,non métallique pour raccord <kleiner => 5 000 PSI circuits hydrauliques

Le présent document spécifie les dimensions, les tolérances et les caractéristiques requises pour les fiches de protection, non métalliques, pour raccords EN 6123, destinées à l’étanchéité des orifices pour les liquides pendant le transport et le stockage afin d’éviter :
- une contamination par moisissure, fluides, produits chimiques et particules,
- un renversement à l’intérieur de l’emballage ou de la section de l’aéronef,
- des endommagements des orifices et de l'extrémité des tuyaux, et
- le bouchage des orifices et des tuyaux à cause de l'absorption de la fiche.
En raison des exigences de propreté, les pièces ne doivent être utilisées qu’une seule fois.

Aeronavtika - Vtič, zaščita, nekovinska, za končno vgradnjo po EN 6123

General Information

Status
Published
Publication Date
24-Sep-2020
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
24-Sep-2020
Due Date
29-Nov-2020
Completion Date
25-Sep-2020

Buy Standard

Standard
EN 6141:2020
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 6141:2020
01-november-2020
Aeronavtika - Vtič, zaščita, nekovinska, za končno vgradnjo po EN 6123
Aerospace series - Plug, protective, non-metallic, for EN 6123 fitting ends
Luft- und Raumfahrt - Stopfen, nicht metallisch, zum Schutz für Endfittinge nach EN
6123
Série aérospatiale - Prise, protectrice,non métallique pour raccord 5 000 PSI
circuits hydrauliques
Ta slovenski standard je istoveten z: EN 6141:2020
ICS:
49.080 Letalski in vesoljski Aerospace fluid systems and
hidravlični sistemi in deli components
SIST EN 6141:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 6141:2020

---------------------- Page: 2 ----------------------
SIST EN 6141:2020


EN 6141
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2020
EUROPÄISCHE NORM
ICS 49.080
English Version

Aerospace series - Plug, protective, non-metallic, for EN
6123 fitting ends
Série aérospatiale - Fiche, de protection, non Luft- und Raumfahrt - Stopfen, nicht metallisch, zum
métallique, pour raccords EN 6123 Schutz für Endfittinge nach EN 6123
This European Standard was approved by CEN on 22 December 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 6141:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 6141:2020
EN 6141:2020 (E)
Contents
Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Requirements . 5
4.1 Configuration, dimensions, tolerances and mass . 5
4.2 Material, surface treatment and colour . 5
4.3 Sealing areas . 5
4.4 Proof Pressure . 5
4.5 Temperature range . 5
4.5.1 Storage and transportation temperature . 5
4.5.2 Installation and removal . 5
4.5.3 Cleanliness . 5
5 Technical requirement. 7
5.1 General . 7
5.2 First article inspection . 7
6 Designation. 7
7 Marking . 7
8 Packaging . 8
9 Technical specification . 8
9.1 Simple standard part . 8
9.2 Production lot (batch) . 8
9.3 Materials . 9
9.4 Approval of manufacturers . 9
9.5 Responsibility for inspection . 9
9.6 Labelling . 9
9.7 Unit and transport packages . 9
Bibliography . 10



2

---------------------- Page: 4 ----------------------
SIST EN 6141:2020
EN 6141:2020 (E)
European foreword
This document (EN 6141:2020) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2021, and conflicting national standards shall
be withdrawn at the latest by March 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, P
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.