Metallic materials - Rockwell hardness test - Part 3: Calibration of reference blocks (ISO 6508-3:2023)

This document specifies a method for the calibration of reference blocks to be used for the indirect
and daily verification of Rockwell hardness testing machines and indenters, as specified in ISO 6508-2.
This document also specifies requirements for Rockwell machines and indenters used for calibrating
reference blocks and specifies methods for their calibration and verification.
Attention is drawn to the fact that the use of hard metal for ball indenters is considered to be the
standard type of Rockwell indenter ball.

Metallische Werkstoffe - Härteprüfung nach Rockwell - Teil 3: Kalibrierung von Härtevergleichsplatten (ISO 6508-3:2023)

In diesem Teil von ISO 6508 ist ein Verfahren für die Kalibrierung von Härtevergleichsplatten festgelegt, die bei der indirekten Überprüfung und täglichen Überprüfung von Härteprüfmaschinen nach Rockwell nach ISO 6508 2: verwendet werden.
Es ist zu beachten, dass als Normeindringkugeln für die Härteprüfung nach Rockwell nur solche aus Hartmetall gelten. Stahleindringkugeln dürfen nur dann noch verwendet werden, wenn sie ISO 6508 1: , Anhang A, entsprechen.

Matériaux métalliques - Essai de dureté Rockwell - Partie 3: Étalonnage des blocs de référence (ISO 6508-3:2023)

L'ISO 6508-3:2015 spécifie une méthode pour l'étalonnage des blocs de référence à utiliser pour la vérification indirecte et la vérification quotidienne des machines d'essai de dureté Rockwell, comme spécifié dans l'ISO 6508‑2:2015.
L'attention est attirée sur le fait que l'utilisation de métaux durs pour les pénétrateurs à billes est considérée être le type courant de bille de pénétrateur Rockwell. Des billes de pénétrateur en acier peuvent continuer d'être utilisées seulement en conformité avec l'Annexe A de l'ISO 6508‑1:2015.

Kovinski materiali - Preskus trdote po Rockwellu - 3. del: Umerjanje primerjalnih ploščic (ISO 6508-3:2023)

Ta dokument določa metodo za umerjanje primerjalnih ploščic, ki se uporabljajo pri posrednem in vsakodnevnem preverjanju naprav za preskušanje trdote po Rockwellu, kot je določeno v standardu ISO 6508-2. Ta dokument določa tudi zahteve za stroje in vtisne naprave za preverjanje trdote po Rockwellu, ki se uporabljajo za umerjanje primerjalnih ploščic, in določa metode za njihovo umerjanje in preverjanje.
Opozoriti je treba, da se za standardno vrsto vtisne krogle po Rockwellu šteje kroglično vtisno telo iz trdine.

General Information

Status
Published
Public Enquiry End Date
22-Jan-2023
Publication Date
05-Mar-2024
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
03-Jan-2024
Due Date
09-Mar-2024
Completion Date
06-Mar-2024

Relations

Buy Standard

Standard
EN ISO 6508-3:2024
English language
25 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 6508-3:2024
01-april-2024
Kovinski materiali - Preskus trdote po Rockwellu - 3. del: Umerjanje primerjalnih
ploščic (ISO 6508-3:2023)
Metallic materials - Rockwell hardness test - Part 3: Calibration of reference blocks (ISO
6508-3:2023)
Metallische Werkstoffe - Härteprüfung nach Rockwell - Teil 3: Kalibrierung von
Härtevergleichsplatten (ISO 6508-3:2023)
Matériaux métalliques - Essai de dureté Rockwell - Partie 3: Étalonnage des blocs de
référence (ISO 6508-3:2023)
Ta slovenski standard je istoveten z: EN ISO 6508-3:2023
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
SIST EN ISO 6508-3:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 6508-3:2024

---------------------- Page: 2 ----------------------
SIST EN ISO 6508-3:2024


EN ISO 6508-3
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2023
EUROPÄISCHE NORM
ICS 77.040.10 Supersedes EN ISO 6508-3:2015
English Version

Metallic materials - Rockwell hardness test - Part 3:
Calibration of reference blocks (ISO 6508-3:2023)
Matériaux métalliques - Essai de dureté Rockwell - Metallische Werkstoffe - Härteprüfung nach Rockwell -
Partie 3: Étalonnage des blocs de référence (ISO 6508- Teil 3: Kalibrierung von Härtevergleichsplatten (ISO
3:2023) 6508-3:2023)
This European Standard was approved by CEN on 13 November 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6508-3:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 6508-3:2024
EN ISO 6508-3:2023 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 6508-3:2024
EN ISO 6508-3:2023 (E)
European foreword
This document (EN ISO 6508-3:2023) has been prepared by Technical Committee ISO/TC 164
"Mechanical testing of metals" in collaboration with Technical Committee CEN/TC 459/SC 1 “Test
methods for steel (other than chemical analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2024, and conflicting national standards shall be
withdrawn at the latest by June 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6508-3:2015.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 6508-3:2023 has been approved by CEN as EN ISO 6508-3:2023 without any
modification.


3

---------------------- Page: 5 ---
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.