Technical report regarding precision data for standards EN 12720, EN 12721, EN 12722, EN 15185 and EN 15186

This document specifies repeatability standard deviation and reproducibility standard deviation for results obtained from tests methods carried out according to following standards:
-   EN 12720:2009+A1:2013, Furniture - Assessment of surface resistance to cold liquids,
-   EN 12721:2009+A1:2013, Furniture - Assessment of surface resistance to wet heat,
-   EN 12722:2009+A1:2013, Furniture - Assessment of surface resistance to dry heat,
-   EN 15185:2011, Furniture - Assessment of the surface resistance to abrasion,
-   EN 15186:2012, Furniture - Assessment of the surface resistance to scratching,
in order to provide the accuracy of results.
The above standards deal with all rigid furniture surfaces regardless of materials and they not apply to leather and textile surfaces.

Technischer Bericht über Präzisionsdaten der Normen EN 12720, EN 12721, EN 12722, EN 15185 und EN 15186

Rapport technique sur les données de fidélité concernant les normes EN 12720, EN 12721, EN 12722, EN 15185 et EN 15186

Le présent document spécifie des écarts-types de répétabilité et des écarts-types de reproductibilité concernant les résultats obtenus par l’application de méthodes d’essai selon les normes suivantes :
- EN 12720:2009+A1:2013, Ameublement - Évaluation de la résistance de la surface aux liquides froids,
- EN 12721:2009+A1:2013, Ameublement - Évaluation de la résistance de la surface à la chaleur humide,
- EN 12722:2009+A1:2013, Ameublement - Évaluation de la résistance de la surface à la chaleur sèche,
- EN 15185:2011, Ameublement - Évaluation de la résistance de la surface à l’abrasion,
- EN 15186:2012, Ameublement - Évaluation de la résistance de la surface à la rayure,
afin d’être en mesure de fournir l’exactitude de ces résultats.
Les normes susmentionnées s’appliquent à toutes les surfaces rigides des meubles, indépendamment des matériaux, et ne s’appliquent pas aux surfaces en cuir et textiles.

Tehnično poročilo o natančnosti rezultatov, dobljenih v skladu s standardi EN 12720, EN 12721, EN 12722, EN 15185 in EN 15186

Ta dokument določa standardni odklon ponovljivosti in standardni odklon obnovljivosti za rezultate, dobljene pri preskusnih metodah, izvedenih v skladu z naslednjimi standardi:
– EN 12720:2009+A1:2013, Pohištvo – ocenjevanje odpornosti površine proti hladnim tekočinam,
– EN 12721:2009+A1:2013, Pohištvo – ocenjevanje odpornosti površine proti vlažni toploti,
– EN 12722:2009+A1:2013, Pohištvo – ocenjevanje odpornosti površine proti suhi toploti,
– EN 15185:2011, Pohištvo – ocenjevanje odpornosti površine proti obrabi,
– EN 15186:2012, Pohištvo – ocenjevanje odpornosti površine proti razenju,
za zagotavljanje natančnosti rezultatov.
Zgornji standardi obravnavajo vse trdne pohištvene površine ne glede na materiale, vendar se ne uporabljajo za usnjene in tekstilne površine.

General Information

Status
Published
Public Enquiry End Date
30-Sep-2018
Publication Date
11-Mar-2019
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
10-Jan-2019
Due Date
17-Mar-2019
Completion Date
12-Mar-2019

Buy Standard

Technical report
TP CEN/TR 17292:2019
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
kTP FprCEN/TR 17292:2018
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TP CEN/TR 17292:2019
01-april-2019
7HKQLþQRSRURþLORRQDWDQþQRVWLUH]XOWDWRYGREOMHQLKYVNODGXVVWDQGDUGL(1
(1(1(1LQ(1
Technical report regarding precision data for standards EN 12720, EN 12721, EN 12722,
EN 15185 and EN 15186
Technischer Bericht über Präzisionsdaten der Normen EN 12720, EN 12721, EN 12722,
EN 15185 und EN 15186
Rapport technique sur les données de fidélité concernant les normes EN 12720, EN
12721, EN 12722, EN 15185 et EN 15186
Ta slovenski standard je istoveten z: CEN/TR 17292:2018
ICS:
97.140 Pohištvo Furniture
SIST-TP CEN/TR 17292:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TP CEN/TR 17292:2019

---------------------- Page: 2 ----------------------

SIST-TP CEN/TR 17292:2019


CEN/TR 17292
TECHNICAL REPORT

RAPPORT TECHNIQUE

November 2018
TECHNISCHER BERICHT
ICS 97.140
English Version

Technical report regarding precision data for standards
EN 12720, EN 12721, EN 12722, EN 15185 and EN 15186
Rapport technique sur les données de fidélité Technischer Bericht über Präzisionsdaten der Normen
concernant les normes EN 12720, EN 12721, EN EN 12720, EN 12721, EN 12722, EN 15185 und EN
12722, EN 15185 et EN 15186 15186


This Technical Report was approved by CEN on 5 November 2018. It has been drawn up by the Technical Committee CEN/TC
207.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 17292:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TP CEN/TR 17292:2019
CEN/TR 17292:2018 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 General principles . 6
5 Repeatability standard deviation and reproducibility standard deviation . 7
5.1 Abrasion . 7
5.2 Scratching . 7
5.2.1 Lineal scratching . 7
5.2.2 Circular scratching . 7
5.3 Cold liquids . 8
5.4 Dry heat . 8
5.5 Wet heat . 8

2

---------------------- Page: 4 ----------------------

SIST-TP CEN/TR 17292:2019
CEN/TR 17292:2018 (E)
European foreword
This document (CEN/TR 17292:2018) has been prepared by Technical Committee CEN/TC 207
“Furniture”, the secretariat of which is held by UNI.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
3

---------------------- Page: 5 ----------------------

SIST-TP CEN/TR 17292:2019
CEN/TR 17292:2018 (E)
1 Scope
This document specifies repeatability standard deviation and reproducibility standard deviation for
results obtained from test methods carried out according to the following standards:
— EN 12720:2009+A1:2013, Furniture — Assessment of surface resistance to cold liquids,
— EN 12721:2009+A1:2013, Furniture — Assessment of surface resistance to wet heat,
— EN 12722:2009+A1:2013, Furniture — Assessment of surface resistance to dry heat,
— EN 15185:2011, Furniture — Assessment of the surface resistance to abrasion,
— EN 15186:2012, Furniture — Assessment of the surface resistance to scratching,
in order to provide the accuracy of results.
The above standards deal with all rigid furniture surfaces regardless of materials and they do not apply
to leather and textile surfaces.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 5725-1:1994, Accuracy (trueness and precision) of measurement methods and results — Part 1:
1)
General principles and definitions
ISO 5725-2:1994, Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic
2)
method for the determination of repeatability and reproducibility of a standard measurement method
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— IEC Electropedia. available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1
precision
closeness of agreement between independent test results obtained under stipulated conditions
Note 1 to entry: Precision depends only on the distribution of random errors and does not relate to the true
value or the specified value.

1)This document is impacted by the corrigendum ISO 5725-1:1994/COR 1:1998, Accuracy (trueness and precision)
of measurement methods and results — Part 1: General principles and definitions Technical corrigendum 1.
2)This document is impacted by the corrigendum ISO 5725-2:1994/COR 1:2002, Accuracy (trueness and precision)
of measurement methods and results — Part 2: Basic method for the determination of repeatability and
reproducibility of a standard measurement method Technical corrigendum 1.
4

---------------------- Page: 6 ----------------------

SIST-TP CEN/TR 17292:2019
CEN/TR 17292:2018 (E)
Note 2 to entry: The measure of precision is usually expressed in terms of imprecision and computed as a
standard deviation of the test results. Less precision is reflected by a larger standard deviation.
Note 3 to entry: “Independent test results” means results obtained in a manner not influenced by any previous
result on the same or similar test object. Quantitative measures of precision depend critically on the stipulated
conditions. Repeatability and reproducibility conditions are particular sets of extreme conditions.
3.2
accuracy
closeness of agreement between a test result and the accepted reference value
Note 1 to entry: The term accuracy, when applied to a set of test results, involves a combination of random
components and a common systematic error or bias component.
3.3
repeatability limit
r
value less than or equal t
...

SLOVENSKI STANDARD
kSIST-TP FprCEN/TR 17292:2018
01-september-2018
7HKQLþQRSRURþLORRQDWDQþQRVWLUH]XOWDWRYGREOMHQLKYVNODGXVVWDQGDUGL(1
(1(1(1LQ(1
Technical report regarding precision data for standards EN 12720, EN 12721, EN 12722,
EN 15185 and EN 15186
Technischer Bericht über Präzisionsdaten der Normen EN 12720, EN 12721, EN 12722,
EN 15185 und EN 15186
Ta slovenski standard je istoveten z: FprCEN/TR 17292
ICS:
97.140 Pohištvo Furniture
kSIST-TP FprCEN/TR 17292:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
kSIST-TP FprCEN/TR 17292:2018

---------------------- Page: 2 ----------------------
kSIST-TP FprCEN/TR 17292:2018


FINAL DRAFT
TECHNICAL REPORT
FprCEN/TR 17292
RAPPORT TECHNIQUE

TECHNISCHER BERICHT

July 2018
ICS 97.140
English Version

Technical report regarding precision data for standards
EN 12720, EN 12721, EN 12722, EN 15185 and EN 15186
 Technischer Bericht über Präzisionsdaten der Normen
EN 12720, EN 12721, EN 12722, EN 15185 und EN
15186


This draft Technical Report is submitted to CEN members for Vote. It has been drawn up by the Technical Committee CEN/TC
207.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a Technical Report. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a Technical Report.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TR 17292:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
kSIST-TP FprCEN/TR 17292:2018
FprCEN/TR 17292:2018 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 General principles . 6
5 Repeatability standard deviation and reproducibility standard deviation . 7
5.1 Abrasion . 7
5.2 Scratching . 7
5.2.1 Lineal scratching . 7
5.2.2 Circular scratching . 7
5.3 Cold liquids . 7
5.4 Dry heat . 8
5.5 Wet heat . 8

2

---------------------- Page: 4 ----------------------
kSIST-TP FprCEN/TR 17292:2018
FprCEN/TR 17292:2018 (E)
European foreword
This document (FprCEN/TR 17292:2018) has been prepared by Technical Committee CEN/TC 207
“Furniture”, the secretariat of which is held by UNI.
This document is currently submitted to the Vote on TR.
3

---------------------- Page: 5 ----------------------
kSIST-TP FprCEN/TR 17292:2018
FprCEN/TR 17292:2018 (E)
1 Scope
This document specifies repeatability standard deviation and reproducibility standard deviation for
results obtained from tests methods carried out according to following standards:
— EN 12720:2009+A1:2013, Furniture — Assessment of surface resistance to cold liquids,
— EN 12721:2009+A1:2013, Furniture — Assessment of surface resistance to wet heat,
— EN 12722:2009+A1:2013, Furniture — Assessment of surface resistance to dry heat,
— EN 15185:2011, Furniture — Assessment of the surface resistance to abrasion,
— EN 15186:2012, Furniture — Assessment of the surface resistance to scratching,
in order to provide the accuracy of results.
The above standards deal with all rigid furniture surfaces regardless of materials and they not apply to
leather and textile surfaces.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 5725-1:1994, Accuracy (trueness and precision) of measurement methods and results — Part 1:
General principles and definitions
ISO 5725-1:1994/COR 1:1998, Accuracy (trueness and precision) of measurement methods and results —
Part 1: General principles and definitions Technical corrigendum 1
ISO 5725-2:1994, Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic
method for the determination of repeatability and reproducibility of a standard measurement method
ISO 5725-2:1994/COR 1:2002, Accuracy (trueness and precision) of measurement methods and results —
Part 2: Basic method for the determination of repeatability and reproducibility of a standard
measurement method Technical corrigendum 1
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia. available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1
precision
closeness of agreement between independent test results obtained under stipulated conditions
Note 1 to entry: Precision depends only on the distribution of random errors and does not relate to the true
value or the specified value.
4

---------------------- Page: 6 ----------------------
kSIST-TP FprCEN/TR 17292:2018
FprCEN/TR 17292:2018 (E)
Note 2 to entry: The measure of precision is usually expressed in terms of imprecision and computed as a
standard deviation of the test results. Less precision is reflected by a larger standard deviation.
Note 3 to entry: “Independent test results” means results obtained in a manner not influenced by any previous
result on the same or similar test object. Quantitative measures of precision depend critically on the stipulated
conditions. Repeatability and reproducibility conditions are particular sets of extreme conditions.
3.2
accuracy
closeness of agreement between a test result and the accepted reference value
Note 1 to entry: The term accuracy, when applied to a set of test results, involves a combination of random
components and a common systematic error or bias component.
3.3
repeatability limit
r
value less than or equal to which the absolute difference between two test results obtained under
repeatabili
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.