SIST EN 60745-2-17:2010
Hand-held motor-operated electric tools - Safety - Part 2-17: Particular requirements for routers and trimmers (IEC 60745-2-17:2010, modified)
Hand-held motor-operated electric tools - Safety - Part 2-17: Particular requirements for routers and trimmers (IEC 60745-2-17:2010, modified)
This standard applies to routers and trimmers.
Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit - Teil 2-17: Besondere Anforderungen für Oberfräsen und Kantenfräsen (IEC 60745-2-17:2010, modifiziert)
Outils électroportatifs à moteur - Sécurité - Partie 2-17: Règles particulières pour les défonceuses et les affleureuses (CEI 60745-2-17:2010, modifiée)
La CEI 60745-2-17:2010 Traite de la sécurité des défonceuses et aux affleureuses ou la tension assignée des outils n'étant pas supérieure à 250 V pour les outils à courant monophasé alternatif ou continu et à 440 V pour les outils à courant alternatif triphasé. Complète ou modifie les articles correspondants de la CEI 60745-1. Cette troisième édition annule et remplace la deuxième édition parue en 2003 dont elle constitue une révision technique. Les principaux changements comprennent: Article 8: Marquages et instructions, addition de certaines mises en garde de sécurité spécifiques aux défonceuses, clarifications en Annexe K, addition de l'Annexe M: Sécurité des plans de travail pour le fonctionnement avec des outils électroportatifs à moteur, et modifications rédactionnelles en vue de l'adaptation à la quatrième édition de la CEI 60745-1.
Električna ročna orodja - Varnost - 2-17. del: Posebne zahteve za rezkalnike in obrezovalnike (IEC 60745-2-17:2010, spremenjen)
Ta standard velja za rezkalnike in obrezovalnike.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60745-2-17:2010
01-december-2010
1DGRPHãþD
SIST EN 60745-2-17:2003
SIST EN 60745-2-17:2003/A11:2007
(OHNWULþQDURþQDRURGMD9DUQRVWGHO 3RVHEQH]DKWHYH]DUH]NDOQLNHLQ
REUH]RYDOQLNH ,(& VSUHPHQMHQ
Hand-held motor-operated electric tools - Safety - Part 2-17: Particular requirements for
routers and trimmers (IEC 60745-2-17:2010, modified)
Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit - Teil 2-17: Besondere
Anforderungen für Oberfräsen und Kantenfräsen (IEC 60745-2-17:2010, modifiziert)
Outils électroportatifs à moteur - Sécurité - Partie 2-17: Règles particulières pour les
défonceuses et les affleureuses (CEI 60745-2-17:2010, modifiée)
Ta slovenski standard je istoveten z: EN 60745-2-17:2010
ICS:
25.080.20 Frezalniki Boring and milling machines
25.140.20 (OHNWULþQDRURGMD Electric tools
SIST EN 60745-2-17:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60745-2-17:2010
---------------------- Page: 2 ----------------------
SIST EN 60745-2-17:2010
EUROPEAN STANDARD
EN 60745-2-17
NORME EUROPÉENNE
September 2010
EUROPÄISCHE NORM
ICS 25.140.20 Supersedes EN 60745-2-17:2003 + A11:2007
English version
Hand-held motor-operated electric tools -
Safety -
Part 2-17: Particular requirements for routers and trimmers
(IEC 60745-2-17:2010, modified)
Outils électroportatifs à moteur - Handgeführte motorbetriebene
Sécurité - Elektrowerkzeuge -
Partie 2-17: Règles particulières Sicherheit -
pour les défonceuses et les affleureuses Teil 2-17: Besondere Anforderungen
(CEI 60745-2-17:2010, modifiée) für Oberfräsen und Kantenfräsen
(IEC 60745-2-17:2010, modifiziert)
This European Standard was approved by CENELEC on 2010-09-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60745-2-17:2010 E
---------------------- Page: 3 ----------------------
SIST EN 60745-2-17:2010
EN 60745-2-17:2010 - 2 -
Foreword
The text of document 116/38/FDIS, future edition 3 of IEC 60745-2-17, prepared by TC 116, Safety of
hand-held motor-operated electric tools, was submitted to the IEC-CENELEC parallel vote.
A draft amendment, prepared by the Technical Committee CENELEC TC 116, Safety of motor-
operated electric tools, was submitted to the formal vote.
The combined texts were approved by CENELEC as EN 60745-2-17 on 2010-09-01.
This European Standard supersedes EN 60745-2-17:2003 + A11:2007.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the amendment has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop) 2011-09-01
– latest date by which the national standards conflicting
with the amendment have to be withdrawn
(dow) 2013-09-01
This European Standard is divided into two parts:
Part 1: General requirements which are common to most hand-held electric motor operated tools
(for the purpose of this standard referred to simply as tools) which could come within the
scope of this standard;
Part 2: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.
This draft European Standard has been prepared under Mandate M/396 given to CENELEC by the
European Commission and the European Free Trade Association and covers essential requirements
of EC Directive 2006/42/EC. See Annex ZZ.
Compliance with the relevant clauses of Part 1 together with this Part 2 provides one means of
conforming with the essential health and safety requirements of the Directive concerned.
Warning: Other requirements and other EC Directives can be applicable to the products falling within
the scope of this standard.
This standard follows the overall requirements of EN ISO 12100-1 and EN ISO 12100-2.
This Part 2-17 is to be used in conjunction with EN 60745-1:2009. When this standard states
"addition", "modification" or "replacement", the relevant text in Part 1 is to be adapted accordingly.
Subclauses, tables and figures which are additional to those in Part 1 are numbered starting from 101;
additional annexes are lettered AA, BB, etc.
Subclauses, tables and figures which are additional to those in IEC 60745-2-17:2010 (116/38/FDIS)
are prefixed “Z”.
---------------------- Page: 4 ----------------------
SIST EN 60745-2-17:2010
- 3 - EN 60745-2-17:2010
Annex ZZ has been added by CENELEC.
NOTE In this standard the following print types are used:
- requirements proper: in roman type
- test specifications: in italic type;
- explanatory matter: in smaller roman type.
__________
Endorsement notice
The text of the International Standard IEC 60745-2-17:2010 was approved by CENELEC as a
European Standard with agreed common modifications as given below.
COMMON MODIFICATIONS
6 Void
Replace by:
6 Environmental requirements
This clause of Part 1 is applicable except as follows:
6.1.2.4 Modification:
Routers and trimmers are suspended. The base plate of the tool shall be horizontal.
6.1.2.5 Modification:
Routers and trimmers are tested at no-load.
6.2 Vibration
6.2.4.2 Location of the measurement
Addition:
Figure Z101 shows the positions at both handles.
6.2.6.3 Operating conditions
Modification:
Trimmers are tested at no-load.
Routers are tested under load observing the conditions shown in Table Z101.
---------------------- Page: 5 ----------------------
SIST EN 60745-2-17:2010
EN 60745-2-17:2010 - 4 -
Table Z101 – Test conditions
Orientation Cutting grooves in a horizontal piece of medium density fibreboard (MDF) having the
minimum dimensions 800 mm (length) x 400 mm (width) x 30 mm (depth).
The board is fixed on a bench by screws, clamps, air cylinders or the like with a resilient
material between bench and workpiece
Tool bit ∅ 12 mm straight sided bit as specified for MDF
Feed force As necessary for smoothly working without overloading the machine. Apply equal force to
both handles avoiding excessive gripping forces
Test cycle Cutting a 10 mm deep groove across the 400 mm width of the MDF. Distance between
grooves to be 10 mm using the guide fence if supplied
6.2.7.2 Declaration of the vibration total value
Addition:
The vibration total value a of the handle with the highest emission and the uncertainty K shall be
h
declared.
8 Marking and instructions
8.12.2 a) Add to the addition:
Z101) for routers: information on the correct use of the dust collection system
Z102) for routers: advice to wear a dust mask
21 Construction
Replace by:
This clause of Part 1 is applicable except as follows:
21.Z1 Addition:
Routers are considered to be tools where a considerable amount of dust is produced.
Trimmers are considered not to be tools where a considerable amount of dust is produced.
Add the following new figure:
---------------------- Page: 6 ----------------------
SIST EN 60745-2-17:2010
- 5 - EN 60745-2-17:2010
Figure Z101 - Position of transducers
---------------------- Page: 7 ----------------------
SIST EN 60745-2-17:2010
EN 60745-2-17:2010 - 6 -
Add the following annex:
Annex ZZ
(informative)
Coverage of Essential Requirements of Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant Essential Requirements as given in EC Directive 2006/42/EC (Machinery Directive).
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directives concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling
within the scope of this standard.
_______________
---------------------- Page: 8 ----------------------
SIST EN 60745-2-17:2010
IEC 60745-2-17
®
Edition 3.0 2010-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Hand-held motor-operated electric tools – Safety –
Part 2-17: Particular requirements for routers and trimmers
Outils électroportatifs à moteur – Sécurité –
Partie 2-17: Règles particulières pour les défonceuses et les affleureuses
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
V
CODE PRIX
ICS 25.140.20 ISBN 978-2-88910-990-6
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 9 ----------------------
SIST EN 60745-2-17:2010
– 2 – 60745-2-17 © IEC:2010
CONTENTS
FOREWORD.4
1 Scope.6
2 Normative references .6
3 Terms and definitions .6
4 General requirements .6
5 General conditions for the tests .6
6 Void.6
7 Classification.6
8 Marking and instructions.7
9 Protection against access to live parts.7
10 Starting .7
11 Input and current .7
12 Heating .7
13 Leakage current .7
14 Moisture resistance .8
15 Electric strength .8
16 Overload protection of transformers and associated circuits .8
17 Endurance.8
18 Abnormal operation .8
19 Mechanical hazards.8
20 Mechanical strength .9
21 Construction .9
22 Internal wiring.9
23 Components .9
24 Supply connection and external flexible cords .9
25 Terminals for external conductors.9
26 Provision for earthing .9
27 Screws and connections .10
28 Creepage distances, clearances and distances through insulation.10
29 Resistance to heat, fire and tracking.10
30 Resistance to rusting.10
31 Radiation, toxicity and similar hazards.10
Annexes .12
Annex K (normative) Battery tools and battery packs .12
Annex L (normative) Battery tools and battery packs provided with mains connection
or non-isolated sources.12
Annex M (normative) Safety of working stands for operation with hand-held motor-
operated electric tools .13
Bibliography.30
---------------------- Page: 10 ----------------------
SIST EN 60745-2-17:2010
60745-2-17 © IEC:2010 – 3 –
Figure 101 – Measurement of distance between handle and cutter .11
Figure M.301 – Working stand with installed hand-held router.23
Figure M.302 – Dimensions of table.23
Figure M.303 – Dimension of table rings .24
Figure M.304 – Fence.24
Figure M.305 – Examples of guides suitable for curved work .25
Figure M.306 – Test probe.26
Figure M.307 – Definition of fence pressure device deflection measuring point and
directions of application of test forces .26
Figure M.308 – Definition of fence pressure device deflection measuring point and
directions of application of test forces (vertical view) .27
Figure M.309 – Definition of table pressure device deflection measuring point and
directions of application of test forces (horizontal view) .27
Figure M.310 – Definition of the adjustable guard deflection measuring points and
directions of application of test forces .28
Figure M.311 – Definition of guiding steady deflection measuring points and directions
of application of test forces .29
Figure M.312 – Definition of the adjustment of the fence plates in the direction
perpendicular to the plane of the fence .29
Table M.301 – Fences and table pressure device displacement .21
Table M.302 – Adjustable guard deflection .21
Table M.303 – Guiding steady deflection .22
---------------------- Page: 11 ----------------------
SIST EN 60745-2-17:2010
– 4 – 60745-2-17 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS –
SAFETY –
Part 2-17: Particular requirements for routers and trimmers
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60745-2-17 has been prepared by IEC technical committee 116:
Safety of hand-held motor-operated electric tools.
This third edition cancels and replaces the second edition published in 2003, of which it
constitutes a technical revision. Main changes include: Clause 8: Marking and instructions,
addition of some router specific safety warnings, clarifications in Annex K, the addition of
Annex M: Safety of working stands for operation with hand-held motor-operated electric tools,
and editorial modifications to match with the fourth edition of IEC 60745-1.
---------------------- Page: 12 ----------------------
SIST EN 60745-2-17:2010
60745-2-17 © IEC:2010 – 5 –
The text of this standard is based on the following documents:
FDIS Report on voting
116/38/FDIS 116/47/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives.
This Part 2-17 is to be used in conjunction with the fourth edition (2006) of IEC 60745-1:
Safety of hand-held motor-operated electric tools – Part 1: General requirements. It was
established on the basis of the fourth edition of that standard.
When this standard states “addition”, “modification” or “replacement”, the relevant text in
Part 1 is to be adapted accordingly.
NOTE In this standard, the following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in smaller roman type.
Subclauses, tables and figures which are additional to those in Part 1 are numbered starting from 101; additional
annexes are lettered AA, BB, etc.
A list of all parts of the IEC 60745 series, under the general title: Hand-held motor-operated
electric tools – Safety, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 13 ----------------------
SIST EN 60745-2-17:2010
– 6 – 60745-2-17 © IEC:2010
HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS –
SAFETY –
Part 2-17: Particular requirements for routers and trimmers
1 Scope
This clause of Part 1 is applicable, except as follows:
Addition:
This standard applies to routers and trimmers.
2 Normative references
This clause of Part 1 is applicable.
3 Terms and definitions
This clause of Part 1 is applicable, except as follows:
Additional definitions:
3.101
router
tool designed to be fitted with rotary cutter and with a base that allows control of cutting slots
into or shaping the edge of various materials
3.102
trimmer
tool designed to be fitted with rotary cutter and a base that allows for control of trimming the
edge of laminate sheet or similar materials
4 General requirements
This clause of Part 1 is applicable.
5 General conditions for the tests
This clause of Part 1 is applicable.
6 Void
7 Classification
This clause of Part 1 is applicable.
---------------------- Page: 14 ----------------------
SIST EN 60745-2-17:2010
60745-2-17 © IEC:2010 – 7 –
8 Marking and instructions
This clause of Part 1 is applicable except as follows:
8.1 Addition:
– rated no-load speed in revolutions per minute.
8.12.1.1 Addition:
– Hold power tool by insulated gripping surfaces, because the cutter may contact its
own cord. Cutting a "live" wire may make exposed metal parts of the power tool "live" and
shock the operator.
– Use clamps or another practical way to secure and support the workpiece to a stable
platform. Holding the work by your hand or against the body leaves it unstable and may
lead to loss of control.
8.12.2 a) Addition:
7) Details of the type of cutters for which the tool is designed
8) Draw attention to the necessity for using bits of the correct shank diameter suitable for the
speed of the tool
9) Information concerning the diameter of shank for which the collet is designed
9 Protection against access to live parts
This clause of Part 1 is applicable.
10 Starting
This clause of Part 1 is applicable.
11 Input and current
This clause of Part 1 is applicable.
12 Heating
This clause of Part 1 is applicable, except as follows:
12.4 Replacement:
The tool is operated for 15 cycles, each cycle comprising a period of continuous operation of
1 min and a rest period of 1 min with the tool switched off. During the periods of operation, the
tool is loaded by means of a brake adjusted so as to attain rated input or rated current. The
th
temperature rises are measured at the end of the 15 “on” period, or at the manufacturer’s
option, the tool may be operated continuously until thermal stabilisation.
13 Leakage current
This clause of Part 1 is applicable.
---------------------- Page: 15 ----------------------
SIST EN 60745-2-17:2010
– 8 – 60745-2-17 © IEC:2010
14 Moisture resistance
This clause of Part 1 is applicable.
15 Electric strength
This clause of Part 1 is applicable.
16 Overload protection of transformers and associated circuits
This clause of Part 1 is applicable.
17 Endurance
This clause of Part 1 is applicable.
18 Abnormal operation
This clause of Part 1 is applicable.
19 Mechanical hazards
This clause of Part 1 is applicable, except as follows:
19.1 Replacement:
Routers shall be equipped with a base plate which surrounds the cutter in the plane of the
plate so as to prevent inadvertent contact with the cutter during normal operation.
Compliance is checked by inspection.
Additional subclauses:
19.4.101 At least two handles are required if the mass exceeds 2 kg.
The handles shall be so shaped or located as to minimise the risk of inadvertent contact of
the user’s hand with rotating parts. Inadvertent contact of the user’s hand is, for example,
considered to be sufficiently prevented if the gripping area of the handle is provided with a
suitable shroud(s) or barrier at its end(s) adjacent to the body of the tool, or the distance from
a defined measuring point on the handle surface to the cutter is a minimum of 120 mm.
Compliance is checked by inspection and measurement. The measurement shall be carried
out as a chain distance (see Figure 101).
With the base plate set to maximum depth of cut, to establish the measuring point on the
auxiliary handle, follow the outlined procedure below.
a) Establish the closest (A) and the most distant (B) points from the plane of the base plate
on the handle. Equidistant between points (A) and (B), draw the horizontal intersecting line
on the plane parallel with the base plate and the surface of the handle.
b) The point on the intersecting line of the handle surface with the largest radial distance
from the centreline of the spindle is the defined measuring point.
---------------------- Page: 16 ----------------------
SIST EN 60745-2-17:2010
60745-2-17 © IEC:2010 – 9 –
The motor housing can be considered as a handle, if suitably shaped.
The mass is measured without accessories, e.g. mandrels, cutters and flexible cable or cord.
If the motor housing is considered as the only gripping area, it shall be so shaped as to
minimise the risk of inadvertent contact of the user with rotating parts. Inadvertent contact of
the hand of the user is considered to be sufficiently prevented, if there is a 6 mm high barrier
between the grasping surface and the cutter or if the mains switch area is at a distance of at
least 120 mm from the cutter, taking into account any base plate which may be fitted.
Adjustment elements capable of being readjusted while the tool is operating, e.g. “revolving
depth gauge”, shall be located so that touching of rotating parts is avoided.
Compliance is checked by inspection.
19.101 The no-load speed of the spindle at rated voltage or at the upper limit of the voltage
range shall not exceed 110 % of the rated no-load speed.
Compliance is checked by measuring the speed of the spindle after the tool has been
operating for 15 min at no-load.
20 Mechanical strength
This clause of Part 1 is applicable.
21 Construction
This clause of Part 1 is applicable.
22 Internal wiring
This clause of Part 1 is applicable.
23 Components
This clause of Part 1 is applicable.
24 Supply connection and external flexible cords
This clause of Part 1 i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.