SIST ISO 3547-2:2020
(Main)Plain bearings - Wrapped bushes - Part 2: Test data for outside and inside diameters
Plain bearings - Wrapped bushes - Part 2: Test data for outside and inside diameters
ISO 3547-2:2017 specifies the test data for outside and inside diameters of wrapped bushes made of mono and multi-layer bearing material for plain bearing applications. It also specifies test designations.
Since the wall thickness of the bush is measured in the free condition, no special test data are required for this on the drawing (see ISO 3547‑5 and ISO 3547‑6).
NOTE Depending on the manufacturing method, the back of the bushes can show isolated light depressions and, similarly, bushes with lubrication holes, grooves and bore indentations can show distortion. It is therefore suggested to measure the wall thickness away from these areas.
Paliers lisses - Bagues roulées
Drsni ležaji - Zvite puše - 2. del: Podatki za preskus zunanjega in notranjega premera
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ISO 3547-2:2020
01-oktober-2020
Drsni ležaji - Zvite puše - 2. del: Podatki za preskus zunanjega in notranjega
premera
Plain bearings - Wrapped bushes - Part 2: Test data for outside and inside diameters
Paliers lisses - Bagues roulées
Ta slovenski standard je istoveten z: ISO 3547-2:2017
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 3547-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 3547-2:2020
---------------------- Page: 2 ----------------------
SIST ISO 3547-2:2020
INTERNATIONAL ISO
STANDARD 3547-2
Third edition
2017-02
Plain bearings — Wrapped bushes —
Part 2:
Test data for outside and inside
diameters
Paliers lisses — Bagues roulées —
Partie 2: Données d’essai pour le diamètre extérieur et le diamètre
intérieur
Reference number
ISO 3547-2:2017(E)
©
ISO 2017
---------------------- Page: 3 ----------------------
SIST ISO 3547-2:2020
ISO 3547-2:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 3547-2:2020
ISO 3547-2:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units . 2
5 Presentation of data on drawing. 2
6 Tests . 4
6.1 Test A . 4
6.2 Test B . 4
6.3 Test C . 4
6.4 Test D . 4
7 Test A . 4
7.1 Description . 4
7.2 Calculation basis . 4
7.2.1 Elastic reduction, v, of outside diameter, D .
o 4
7.2.2 Calculation of diameter of checking block, d .
ch, 1 5
7.2.3 Effective cross-sectional area, A .
cal 5
7.2.4 Calculation of checking load, F .
ch 6
7.2.5 Limits for Δz .7
7.3 Obtaining data — Example . 7
7.4 Presentation of data on drawing — Example . 8
8 Test B . 8
8.1 Description . 8
8.2 Obtaining data — Example . 9
8.3 Presentation of data on drawing — Example . 9
9 Test C . 9
9.1 Description . 9
9.2 Obtaining data — Example .10
9.3 Presentation of data on drawing — Example .10
10 Test D .11
10.1 Description .11
10.2 Obtaining data — Example .11
10.3 Presentation of data on drawing — Example .11
11 Designation of tests according to this document .12
Bibliography .13
© ISO 2017 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 3547-2:2020
ISO 3547-2:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www . i so .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3,
Dimensions, tolerances and construction details.
This third edition cancels and replaces the second edition (ISO 3547-2:2006), which has been technically
revised.
A list of all the parts in the ISO 3547 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 3547-2:2020
INTERNATIONAL STANDARD ISO 3547-2:2017(E)
Plain bearings — Wrapped bushes —
Part 2:
Test data for outside and inside diameters
1 Scope
This document specifies the test data for outside and inside diameters of wrapped bushes made of
mono and multi-layer bearing material for plain bearing applications. It also specifies test designations.
Since the wall thickness of the bush is measured in the free condition, no special test data are required
for this on the drawing (see ISO 3547-5 and ISO 3547-6).
NOTE Depending on the manufacturing method, the back of the bushes can show isolated light depressions
and, similarly, bushes with lubrication holes, grooves and bore indentations can show distortion. It is therefore
suggested to measure the wall thickness away from these areas.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 286-2, Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes —
Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
1)
ISO 3547-1:— , Plain bearings — Wrapped bushes — Part 1: Dimensions
ISO 3547-4, Plain bearings — Wrapped bushes — Part 4: Materials
ISO 3547-5, Plain bearings — Wrapped bushes — Part 5: Checking the outside diameter
ISO 4378-1, Plain bearings — Terms, definitions, classification and symbols — Part 1: Design, bearing
materials and their properties
ISO 4378-4, Plain bearings — Terms, definitions, classification and symbols — Part 4: Basic symbols
ISO 12301, Plain bearings — Quality control techniques and inspection of geometrical and material quality
characteristics
ISO 13715, Technical drawings — Edges of undefined shape — Vocabulary and indication
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4378-1 and ISO 4378-4 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http:// www .iso .
...
INTERNATIONAL ISO
STANDARD 3547-2
Third edition
2017-02
Plain bearings — Wrapped bushes —
Part 2:
Test data for outside and inside
diameters
Paliers lisses — Bagues roulées —
Partie 2: Données d’essai pour le diamètre extérieur et le diamètre
intérieur
Reference number
ISO 3547-2:2017(E)
©
ISO 2017
---------------------- Page: 1 ----------------------
ISO 3547-2:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 3547-2:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units . 2
5 Presentation of data on drawing. 2
6 Tests . 4
6.1 Test A . 4
6.2 Test B . 4
6.3 Test C . 4
6.4 Test D . 4
7 Test A . 4
7.1 Description . 4
7.2 Calculation basis . 4
7.2.1 Elastic reduction, v, of outside diameter, D .
o 4
7.2.2 Calculation of diameter of checking block, d .
ch, 1 5
7.2.3 Effective cross-sectional area, A .
cal 5
7.2.4 Calculation of checking load, F .
ch 6
7.2.5 Limits for Δz .7
7.3 Obtaining data — Example . 7
7.4 Presentation of data on drawing — Example . 8
8 Test B . 8
8.1 Description . 8
8.2 Obtaining data — Example . 9
8.3 Presentation of data on drawing — Example . 9
9 Test C . 9
9.1 Description . 9
9.2 Obtaining data — Example .10
9.3 Presentation of data on drawing — Example .10
10 Test D .11
10.1 Description .11
10.2 Obtaining data — Example .11
10.3 Presentation of data on drawing — Example .11
11 Designation of tests according to this document .12
Bibliography .13
© ISO 2017 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 3547-2:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www . i so .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3,
Dimensions, tolerances and construction details.
This third edition cancels and replaces the second edition (ISO 3547-2:2006), which has been technically
revised.
A list of all the parts in the ISO 3547 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 3547-2:2017(E)
Plain bearings — Wrapped bushes —
Part 2:
Test data for outside and inside diameters
1 Scope
This document specifies the test data for outside and inside diameters of wrapped bushes made of
mono and multi-layer bearing material for plain bearing applications. It also specifies test designations.
Since the wall thickness of the bush is measured in the free condition, no special test data are required
for this on the drawing (see ISO 3547-5 and ISO 3547-6).
NOTE Depending on the manufacturing method, the back of the bushes can show isolated light depressions
and, similarly, bushes with lubrication holes, grooves and bore indentations can show distortion. It is therefore
suggested to measure the wall thickness away from these areas.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 286-2, Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes —
Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
1)
ISO 3547-1:— , Plain bearings — Wrapped bushes — Part 1: Dimensions
ISO 3547-4, Plain bearings — Wrapped bushes — Part 4: Materials
ISO 3547-5, Plain bearings — Wrapped bushes — Part 5: Checking the outside diameter
ISO 4378-1, Plain bearings — Terms, definitions, classification and symbols — Part 1: Design, bearing
materials and their properties
ISO 4378-4, Plain bearings — Terms, definitions, classification and symbols — Part 4: Basic symbols
ISO 12301, Plain bearings — Quality control techniques and inspection of geometrical and material quality
characteristics
ISO 13715, Technical drawings — Edges of undefined shape — Vocabulary and indication
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4378-1 and ISO 4378-4 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
1) Under preparation. Stage at the time of publication: ISO/DIS 3547-1:2016.
© ISO 2017 – All rights reserved 1
---------------------- Page: 5 ----------------------
ISO 3547-2:2017(E)
4 Symbols and units
See Table 1.
Table 1 — Symbols
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.