Fuel cell technologies - Part 8-201: Energy storage systems using fuel cell modules in reverse mode - Test procedures for the performance of power-to-power systems (IEC 62282-8-201:2020)

EN-IEC 62282-8-201 defines the evaluation methods of typical performances for electricenergy storage systems using hydrogen. This is applicable to the systems that useelectrochemical reaction devices for both power charge and discharge. This document appliesto systems that are designed and used for service and operation in stationary locations (indoorand outdoor).The conceptual configurations of the electric energy storage systems using hydrogen are shownin Figure 1 and Figure 2. Figure 1 shows the system independently equipped with an electrolysermodule and a fuel cell module. Figure 2 shows the system equipped with a reversible cellmodule. There are an electrolyser, a hydrogen storage and a fuel cell, or a reversible cell, ahydrogen storage and an overall management system (which may include a pressuremanagement) as indispensable components. There may be a battery, an oxygen storage, a heatmanagement system (which may include a heat storage) and a water management system(which may include a water storage) as optional components. The performance measurement isexecuted in the area surrounded by the outside thick solid line square (system boundary).NOTE In the context of this document, the term "reversible" does not refer to the thermodynamic meaning of an idealprocess. It is common practice in the fuel cell community to call the operation mode of a cell that alternates betweenfuel cell mode and electrolysis mode "reversible".This document is intended to be used for data exchanges in commercial transactions betweenthe system manufacturers and customers. Users of this document can selectively execute testitems suitable for their purposes from those described in this document.

Brennstoffzellentechnologien – Teil 8-201: Energiespeichersysteme mit Brennstoffzellenmodulen im reversiblen Betrieb – Prüfverfahren zum Leistungsverhalten von Power-to-Power-Systemen (IEC 62282-8-201:2020)

Technologies des piles à combustible - Partie 8-201: Systèmes de stockage de l’énergie utilisant des modules à piles à combustible en mode inversé - Procédures d'essai pour la performance des systèmes électriques à électriques (IEC 62282-8-201:2020)

l'IEC 62282-8-201:2020 définit les méthodes d'évaluation des performances typiques des systèmes de stockage de l'énergie électrique utilisant de l'hydrogène. Ces méthodes s'appliquent aux systèmes qui utilisent des dispositifs à réaction électrochimique à la fois pour la charge électrique et la décharge électrique. Le présent document s'applique aux systèmes conçus et utilisés pour l'entretien et le fonctionnement dans des emplacements stationnaires (intérieur et extérieur).
La Figure 1 et la Figure 2 représentent les configurations conceptuelles des systèmes de stockage de l'énergie électrique utilisant de l'hydrogène. La Figure 1 présente un système indépendant équipé d'un module électrolyseur et d'un module à pile à combustible. La Figure 2 représente le système équipé d'un module à cellule réversible. Un électrolyseur, un système de stockage de l'hydrogène et une pile à combustible, ou une cellule réversible, un système de stockage de l'hydrogène et un système de gestion global (pouvant inclure la gestion de la pression) constituent les composants indispensables. Une batterie, un système de stockage de l'oxygène, un système de gestion thermique (pouvant inclure le stockage thermique) et un système de gestion de l'eau (pouvant inclure le stockage de l'eau) constituent les composants facultatifs. Le mesurage des performances s'effectue dans la zone délimitée par le carré extérieur à traits pleins épais (limites du système).

Tehnologija gorivnih celic - 8-201. del: Sistemi za shranjevanje energije, ki uporabljajo module gorivnih celic v obrnjeni smeri - Preskusni postopki za delovanje elektroenergetskih sistemov (IEC 62282-8-201:2020)

General Information

Status
Published
Publication Date
29-Mar-2020
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
12-Mar-2020
Due Date
17-May-2020
Completion Date
30-Mar-2020

Relations

Buy Standard

Standard
EN IEC 62282-8-201:2020 - BARVE
English language
36 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 62282-8-201:2020
01-maj-2020
Tehnologija gorivnih celic - 8-201. del: Sistemi za shranjevanje energije, ki
uporabljajo module gorivnih celic v obrnjeni smeri - Preskusni postopki za
delovanje elektroenergetskih sistemov (IEC 62282-8-201:2020)
Fuel cell technologies - Part 8-201: Energy storage systems using fuel cell modules in
reverse mode - Test procedures for the performance of power-to-power systems (IEC
62282-8-201:2020)
Brennstoffzellentechnologien – Teil 8-201: Energiespeichersysteme mit
Brennstoffzellenmodulen im reversiblen Betrieb – Prüfverfahren zum Leistungsverhalten
von Power-to-Power-Systemen (IEC 62282-8-201:2020)
Technologies des piles à combustible - Partie 8-201: Systèmes de stockage de l’énergie
utilisant des modules à piles à combustible en mode inversé - Procédures d'essai pour la
performance des systèmes électriques à électriques (IEC 62282-8-201:2020)
Ta slovenski standard je istoveten z: EN IEC 62282-8-201:2020
ICS:
27.070 Gorilne celice Fuel cells
SIST EN IEC 62282-8-201:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 62282-8-201:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 62282-8-201:2020


EUROPEAN STANDARD EN IEC 62282-8-201

NORME EUROPÉENNE

EUROPÄISCHE NORM
March 2020
ICS 27.070

English Version
Fuel cell technologies - Part 8-201: Energy storage systems
using fuel cell modules in reverse mode - Test procedures for
the performance of power-to-power systems
(IEC 62282-8-201:2020)
Technologies des piles à combustible - Partie 8-201: Brennstoffzellentechnologien – Teil 8-201:
Systèmes de stockage de l'énergie utilisant des modules à Energiespeichersysteme mit Brennstoffzellenmodulen im
piles à combustible en mode inversé - Procédures d'essai reversiblen Betrieb – Prüfverfahren zum Leistungsverhalten
pour la performance des systèmes électriques à électriques von Power-to-Power-Systemen
(IEC 62282-8-201:2020) (IEC 62282-8-201:2020)
This European Standard was approved by CENELEC on 2020-02-14. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 62282-8-201:2020 E

---------------------- Page: 3 ----------------------
SIST EN IEC 62282-8-201:2020
EN IEC 62282-8-201:2020 (E)
European foreword
The text of document 105/764/FDIS, future edition 1 of IEC 62282-8-201, prepared by IEC/TC 105
"Fuel cell technologies" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC
as EN IEC 62282-8-201:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-11-14
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-02-14
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 62282-8-201:2020 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60079-0 NOTE Harmonized as EN IEC 60079-0
IEC 60079-10-1 NOTE Harmonized as EN 60079-10-1
IEC 60079-29-2 NOTE Harmonized as EN 60079-29-2
IEC 60364 series NOTE Harmonized as HD 60364 series
IEC 61000-4-7 NOTE Harmonized as EN 61000-4-7
IEC 61000-4-13 NOTE Harmonized as EN 61000-4-13
IEC 61960-3 NOTE Harmonized as EN 61960-3
IEC 61987-1 NOTE Harmonized as EN 61987-1
IEC 62282-2 NOTE Harmonized as EN 62282-2
IEC 62282-3-100 NOTE Harmonized as EN 62282-3-100
IEC 62282-3-300 NOTE Harmonized as EN 62282-3-300
IEC 62933-1:2018 NOTE Harmonized as EN IEC 62933-1:2018 (not modified)
ISO 15839 NOTE Harmonized as EN ISO 15839


2

---------------------- Page: 4 ----------------------
SIST EN IEC 62282-8-201:2020
EN IEC 62282-8-201:2020 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61427-1 - Secondary cells and batteries for EN 61427-1 -
renewable energy storage - General
requirements and methods of test - Part 1:
Photovoltaic off-grid application
IEC 61427-2 - Secondary cells and batteries for EN 61427-2 -
renewable energy storage - General
requirements and methods of test - Part 2:
On-grid applications
IEC 62282-3-200 - Fuel cell technologies - Part 3-200: EN 62282-3-200 -
Stationary fuel cell power systems -
Performance test methods
IEC 62282-3-201 - Fuel cell technologies - Part 3-201: EN 62282-3-201 -
Stationary fuel cell power systems -
Performance test methods for small fuel
cell power systems
IEC 62282-8-101 - Fuel cell technologies - Part 8-101: Energy - -
storage systems using fuel cell modules in
reverse mode - Test procedures for the
performance of solid oxide single cells and
stacks, including reversible operation
1
IEC 62282-8-102 - Fuel cell technologies - Part 8-102: Energy EN IEC 62282-8-102 -
storage systems using fuel cell modules in
reverse mode - Test procedures for the
performance of single cells and stacks with
proton exchange membrane, including
reversible operation
IEC 62933-2-1 2017 Electrical energy storage (EES) systems - EN IEC 62933-2-1 2018
Part 2-1: Unit parameters and testing
methods - General specification

1
To be published. Stage at the time of publication: prEN IEC 62282-8-102:2018.
3

---------------------- Page: 5 ----------------------
SIST EN IEC 62282-8-201:2020
EN IEC 62282-8-201:2020 (E)
ISO/IEC Guide - Uncertainty of measurement - Part 3: Guide - -
98-3 to the expression of uncertainty in
measurement (GUM:1995)
ISO 3746 - Acoustics - Determination of sound power EN ISO 3746 -
levels and sound energy levels of noise
sources using sound pressure - Survey
method using an enveloping measurement
surface over a reflecting plane
ISO 4064-1 - Water meters for cold potable water and EN ISO 4064-1 -
hot water - Part 1: Metrological and
technical requirements
ISO 4064-2 - Water meters for cold potable water and EN ISO 4064-2 -
hot water - Part 2: Test methods
ISO 7888 - Water quality - Determination of electrical EN 27888 -
conductivity
ISO 9614-1 - Acoustics - Determination of sound power EN ISO 9614-1 -
levels of noise sources using sound
intensity - Part 1: Measurement at discrete
points
ISO 11204 - Acoustics - Noise emitted by machinery EN ISO 11204 -
and equipment - Determination of emission
sound pressure levels at a work station and
at other specified positions applying
accurate environmental corrections
ISO 16111 - Transportable gas storage devices - - -
Hydrogen absorbed in reversible metal
hydride
ISO 19880-1 - Gaseous hydrogen - Fuelling stations - Part - -
1: General requirements
ISO 19881 - Gaseous hydrogen - Land vehicle fuel - -
containers
ISO 19882 - Gaseous hydrogen - Thermally activated - -
pressure relief devices for compressed
hydrogen vehicle fuel containers
2
ISO 19884 - Gaseous hydrogen - Cylinders and tubes EN ISO 19884 -
for stationary storage
ISO 22734-1 - Hydrogen generators using water - -
electrolysis process - Part 1: Industrial and
commercial applications
ISO 22734-2 - Hydrogen generators using water - -
electrolysis process - Part 2: Residential
applications



2
To be published. Stage at the time of publication: FprEN ISO 19884:2019.
4

---------------------- Page: 6 ----------------------
SIST EN IEC 62282-8-201:2020




IEC 62282-8-201

®


Edition 1.0 2020-01




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Fuel cell technologies –

Part 8-201: Energy storage systems using fuel cell modules in reverse mode –

Test procedures for the performance of power-to-power systems




Technologies des piles à combustible –

Partie 8-201: Systèmes de stockage de l'énergie utilisant des modules à piles à


combustible en mode inversé – Procédures d'essai pour la performance des

systèmes électriques à électriques












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 27.070 ISBN 978-2-8322-7685-3




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 62282-8-201:2020
– 2 – IEC 62282-8-201:2020 © IEC 2020
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 8
3 Terms, definitions and symbols . 9
3.1 Terms and definitions. 9
3.2 Symbols . 13
4 Measurement instruments and measurement methods . 14
4.1 General . 14
4.2 Instrument uncertainty . 15
4.3 Measurement plan . 15
4.4 Environmental conditions . 16
4.5 Maximum permissible variation in test operating conditions . 17
5 System parameters . 17
5.1 General . 17
5.2 Electric energy storage capacity . 17
5.3 Rated electric power input . 18
5.4 Rated net electric power output. 18
5.5 Roundtrip electrical efficiency . 18
5.6 System response (step response time and ramp rate) . 18
5.6.1 Step response time . 18
5.6.2 Ramp rate . 19
5.7 Minimum switchover time . 20
5.8 Quiescent state loss rate . 20
5.9 Heat input rate . 20
5.10 Recovered heat output rate . 20
5.11 Acoustic noise level . 20
5.12 Total harmonic distortion . 20
5.13 Discharge water quality . 21
6 Test methods and procedures . 21
6.1 General . 21
6.2 Electric energy storage capacity test . 21
6.3 Rated electric power input test . 22
6.4 Rated net electric power output test . 22
6.5 Roundtrip electrical efficiency test . 23
6.6 Other system performance test . 23
6.6.1 System response test, step response time and ramp rate . 23
6.6.2 Minimum switchover time test . 25
6.6.3 Quiescent state loss rate test . 25
6.6.4 Heat input rate test . 26
6.6.5 Recovered heat output rate test . 26
6.6.6 Acoustic noise level test . 26
6.6.7 Total harmonic distortion test . 27
6.6.8 Discharge water quality test . 27
6.7 Component performance test . 27
6.7.1 Electrolyser performance test . 27

---------------------- Page: 8 ----------------------
SIST EN IEC 62282-8-201:2020
IEC 62282-8-201:2020 © IEC 2020 – 3 –
6.7.2 Hydrogen storage performance test . 28
6.7.3 Fuel cell performance test . 28
6.7.4 Water management system performance test . 29
6.7.5 Battery performance test . 29
6.7.6 Oxygen storage performance test . 29
7 Test reports . 29
7.1 General . 29
7.2 Report items . 29
7.3 Tested system data description . 30
7.4 Test condition description . 30
7.5 Test data description . 30
7.6 Uncertainty evaluation . 30
Bibliography . 31

Figure 1 – System configuration of electric energy storage system using hydrogen – Type
with electrolyser and fuel cell . 7
Figure 2 – System configuration of electric energy storage system using hydrogen – Type
with reversible cell . 8
Figure 3 – Typical sequence of phases during the system operation . 16
Figure 4 – Step response time and ramp rate of EES system . 19
Figure 5 – Step response test . 24
Figure 6 – Minimum switch over time test . 25

Table 1 – Symbols . 14
Table 2 – Required steps before executing the measurement . 16
Table 3 – Example of document format of roundtrip electrical efficiency . 23
Table 4 – Additional parameters measured on the electrolyser or the reversible cell

module in electrolysis mode . 27
Table 5 – Additional parameters measured on the hydrogen storage component . 28
Table 6 – Additional parameters measured on the fuel cell or the reversible cell module
in fuel cell mode . 28

---------------------- Page: 9 ----------------------
SIST EN IEC 62282-8-201:2020
– 4 – IEC 62282-8-201:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FUEL CELL TECHNOLOGIES –

Part 8-201: Energy storage systems using fuel cell modules in reverse
mode – Test procedures for the performance of power-to-power systems

FOREWORD
1) The International Electro technical Commission (IEC) is a worldwide organization for standardization comprising
all national electro technical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in
addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses
arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62282-8-201 has been prepared by IEC technical committee 105:
Fuel cell technologies.
The text of this International Standard is based on the following documents:
FDIS Report on voting
105/764/FDIS 105/777/RVD

Full information on the voting for the approval of this International Standard can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 62282 series, published under the general title Fuel cell technologies,
can be found on the IEC website.

---------------------- Page: 10 ----------------------
SIST EN IEC 62282-8-201:2020
IEC 62282-8-201:2020 © IEC 2020 – 5 –
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this document using a colour printer.

---------------------- Page: 11 ----------------------
SIST EN IEC 62282-8-201:2020
– 6 – IEC 62282-8-201:2020 © IEC 2020
INTRODUCTION
This part of IEC 62282 describes performance evaluation methods for electric energy storage
systems using hydrogen that employ electrochemical reactions both for water/steam electrolysis
and electric generation.
This document is intended for power to power systems which typically employ a set of
electrolyser and fuel cell, or a reversible cell for devices of electric charge and discharge.
A typical targeting application of the electric energy storage systems using hydrogen is in the
class of energy intensive electric energy storage. The systems are recognized as critically
useful for the relatively long-term power storage operation, such as efficient storage and supply
of the renewable power derived electric energy and grid stabilization.
IEC 62282-8 (all parts) aims to develop performance test methods for power storage and
buffering systems based on electrochemical modules (combining electrolysis and fuel cells, in
particular reversible cells), taking into consideration both options of re-electrification and
substance (and heat) production for sustainable integration of renewable energy sources.
Under the general title Energy storage systems using fuel cell modules in reverse mode, the
IEC 62282-8 series consists of the following parts:
• IEC 62282-8-101: Test procedures for the performance of solid oxide single cells and stacks,
including reversible operation
• IEC 62282-8-102: Test procedures for the performance of single cells and stacks with proton
exchange membranes, including reversible operation
1
• IEC 62282-8-103 : Alkaline single cell and stack performance including reversible operation
• IEC 62282-8-201: Test procedures for the performance of power-to-power systems
2
• IEC 62282-8-202 : Power-to-power systems – Safety
3
• IEC 62282-8-300 (all parts) : Power-to-substance systems
As a priority dictated by the emerging needs for industry and opportunities for technological
development, IEC 62282-8-101, IEC 62282-8-102 and IEC 62282-8-201 have been initiated
jointly and firstly. These parts are presented as a package to highlight the need for an integrated
approach as regards the system's application (i.e. a solution for energy storage) and its
fundamental constituent components (i.e. fuel cells operated in reverse or reversing mode).
IEC 62282-8-103, IEC 62282-8-202 and IEC 62282-8-300 (all parts) are suggested but are left
for initiation at a later stage.


____________
1
 Under consideration.
2
 Under consideration.
3
 Under consideration.

---------------------- Page: 12 ----------------------
SIST EN IEC 62282-8-201:2020
IEC 62282-8-201:2020 © IEC 2020 – 7 –
FUEL CELL TECHNOLOGIES –

Part 8-201: Energy storage systems using fuel cell modules in reverse
mode – Test procedures for the performance of power-to-power systems



1 Scope
This part of IEC 62282 defines the evaluation methods of typical performances for electric
energy storage systems using hydrogen. This is applicable to the systems that use
electrochemical reaction devices for both power charge and discharge. This document applies
to systems that are designed and used for service and operation in stationary locations (indoor
and outdoor).
The conceptual configurations of the electric energy storage systems using hydrogen are shown
in Figure 1 and Figure 2. Figure 1 shows the system independently equipped with an electrolyser
module and a fuel cell module. Figure 2 shows the system equipped with a reversible cell
module. There are an electrolyser, a hydrogen storage and a fuel cell, or a reversible cell, a
hydrogen storage and an overall management system (which may include a pressure
management) as indispensable components. There may be a battery, an oxygen storage, a heat
management system (which may include a heat storage) and a water management system
(which may include a water storage) as optional components. The performance measurement is
executed in the area surrounded by the outside thick solid line square (system boundary).
NOTE In the context of this document, the term "reversible" does not refer to the thermodynamic meaning of an ideal
process. It is common practice in the fuel cell community to call the operation mode of a cell that alternates between
fuel cell mode and electrolysis mode "reversible".
This document is intended to be used for data exchanges in commercial transactions between
the system manufacturers and customers. Users of this document can selectively execute test
items suitable for their purposes from those described in this document.

Figure 1 – System configuration of electric energy storage system using hydrogen
– Type with electrolyser and fuel cell

---------------------- Page: 13 ----------------------
SIST EN I
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.