Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures - General guidance (IEC 60794-1-2:2021)

This part of IEC 60794-1 applies to optical fibre cables for use with telecommunications
equipment and devices employing similar techniques, and to cables having a combination of
both optical fibres and electrical conductors.
An objective of this document is to define general requirements and methodology guidance
applicable to all of the cable test methods of IEC 60794-1 (all parts).
A second objective of this document is to provide the end user with an overview of the different
test methods contained in the different parts of the IEC 60794-1 series, numbered -Xnn.
Table 1 shows the different parts.
These documents define test procedures to be used in establishing uniform requirements for
the geometrical, transmission, material, mechanical, ageing (environmental exposure) and
climatic properties of optical fibre cables, and electrical requirements where appropriate.
Throughout the documents, the wording "optical cable" can also include optical fibre units,
microduct fibre units, etc.
The secondary objective of this document is to provide the end user with useful guidance when
testing optical fibre cables.

Lichtwellenleiterkabel - Teil 1-2: Fachgrundspezifikation - Grundlegende Prüfverfahren für Lichtwellenleiterkabel – Allgemeine Anleitung (IEC 60794-1-2:2021)

Câbles à fibres optiques - Partie 1-2: Spécification générique - Procédures fondamentales d'essais des câbles optiques - Lignes directrices générales (IEC 60794-1-2:2021)

IEC 60794-1-2:2021 est disponible sous forme de IEC 60794-1-2:2021 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'�dition pr�c�dente.

L'IEC 60794-1-2:2021 s’applique aux câbles à fibres optiques destinés à être utilisés dans les équipements de télécommunications et les dispositifs utilisant des techniques analogues, ainsi qu'aux câbles constitués d'une combinaison de fibres optiques et de conducteurs électriques. L'un des objectifs de cette spécification est de définir des exigences générales et des recommandations méthodologiques applicables à toutes les méthodes d'essai des câbles de l'IEC 60794-1 (toutes les parties). Un second objectif du présent document est de fournir à l'utilisateur final une vue d'ensemble des différentes méthodes d’essai contenues dans les différentes parties de la série IEC 60794-1. Cette cinquième édition annule et remplace la quatrième édition parue en 2017. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
- ajout de tableaux de correspondances énonçant les nouveaux numéros de méthodes d'essai et les anciens numéros de méthodes d'essai.

Optični kabli - 1-2. del: Splošna specifikacija - Osnovni preskusni postopki za optične kable - Splošno navodilo (IEC 60794-1-2:2021)

General Information

Status
Published
Publication Date
07-Mar-2021
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
05-Mar-2021
Due Date
10-May-2021
Completion Date
08-Mar-2021

Relations

Buy Standard

Standard
EN IEC 60794-1-2:2021
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 60794-1-2:2021
01-maj-2021
Nadomešča:
SIST EN 60794-1-2:2017
SIST EN 60794-1-2:2017/AC:2017
Optični kabli - 1-2. del: Splošna specifikacija - Osnovni preskusni postopki za
optične kable - Splošno navodilo (IEC 60794-1-2:2021)
Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures
- General guidance (IEC 60794-1-2:2021)
Lichtwellenleiterkabel - Teil 1-2: Fachgrundspezifikation - Grundlegende Prüfverfahren
für Lichtwellenleiterkabel – Allgemeine Anleitung (IEC 60794-1-2:2021)
Câbles à fibres optiques - Partie 1-2: Spécification générique - Procédures
fondamentales d'essais des câbles optiques - Lignes directrices générales (IEC 60794-1
-2:2021)
Ta slovenski standard je istoveten z: EN IEC 60794-1-2:2021
ICS:
33.180.10 (Optična) vlakna in kabli Fibres and cables
SIST EN IEC 60794-1-2:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60794-1-2:2021

---------------------- Page: 2 ----------------------
SIST EN IEC 60794-1-2:2021


EUROPEAN STANDARD EN IEC 60794-1-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
February 2021
ICS 33.180.10 Supersedes EN 60794-1-2:2017 and all of its
amendments and corrigenda (if any)
English Version
Optical fibre cables - Part 1-2: Generic specification - Basic
optical cable test procedures - General guidance
(IEC 60794-1-2:2021)
Câbles à fibres optiques - Partie 1-2: Spécification Lichtwellenleiterkabel - Teil 1-2: Fachgrundspezifikation -
générique - Procédures fondamentales d'essais des câbles Grundlegende Prüfverfahren für Lichtwellenleiterkabel -
optiques - Recommandations générales Allgemeine Anleitung
(IEC 60794-1-2:2021) (IEC 60794-1-2:2021)
This European Standard was approved by CENELEC on 2021-02-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60794-1-2:2021 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60794-1-2:2021
EN IEC 60794-1-2:2021 (E)
European foreword
The text of document 86A/2009/CDV, future edition 5 of IEC 60794-1-2, prepared by SC 86A "Fibres
and cables" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 60794-1-2:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-11-19
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-02-19
document have to be withdrawn
This document supersedes EN 60794-1-2:2017 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60794-1-2:2021 was approved by CENELEC as a
European Standard without any modification.
2

---------------------- Page: 4 ----------------------
SIST EN IEC 60794-1-2:2021
EN IEC 60794-1-2:2021 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60793-1-40 - Optical fibres - Part 1-40: Attenuation EN IEC 60793-1-40 -
measurement methods
IEC 60793-1-46 - Optical fibres - Part 1-46: Measurement EN 60793-1-46 -
methods and test procedures - Monitoring
of changes in optical transmittance
IEC 60793-2-40 - Optical fibres - Part 2-40: Product EN 60793-2-40 -
specifications - Sectional specification for
category A4 multimode fibres
IEC 60794-1-1 - Optical fibre cables - Part 1-1: Generic EN 60794-1-1 -
specification - General
IEC 60794-1-21 2015 Optical fibre cables - Part 1-21: Generic EN 60794-1-21 2015
specification - Basic optical cable test
procedures - Mechanical tests methods
IEC 60794-1-22 2017 Optical fibre cables - Part 1-22: Generic EN IEC 60794-1-22 2018
specification - Basic optical cable test
procedures - Environmental test methods
IEC 60794-1-23 2019 Optical fibre cables - Part 1-23: Generic EN IEC 60794-1-23 2019
specification - Basic optical cable test
procedures - Cable element test methods
IEC 60794-1-24 2014 Optical fibre cables - Part 1-24: Generic EN 60794-1-24 2014
specification - Basic optical cable test
procedures - Electrical test methods

3

---------------------- Page: 5 ----------------------
SIST EN IEC 60794-1-2:2021

---------------------- Page: 6 ----------------------
SIST EN IEC 60794-1-2:2021



IEC 60794-1-2

®


Edition 5.0 2021-01




INTERNATIONAL



STANDARD




NORME


INTERNATIONALE











Optical fibre cables –

Part 1-2: Generic specification – Basic optical cable test procedures – General

guidance



Câbles à fibres optiques –

Partie 1-2: Spécification générique – Procédures fondamentales d'essais des


câbles optiques – Recommandations générales













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.180.10 ISBN 978-2-8322-9248-8




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 60794-1-2:2021
– 2 – IEC 60794-1-2:2021 © IEC 2021
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 7
3 Terms and definitions . 7
4 General guidance . 7
4.1 Test procedure format . 7
4.2 Standard atmospheric conditions . 7
4.3 Symbols and abbreviated terms . 8
4.4 Safety and environmental aspects. 8
4.5 Calibration . 8
4.5.1 Calibration process . 8
4.5.2 Assessment of uncertainties . 8
4.6 Preconditioning . 9
4.7 Guide to qualification sampling . 9
4.8 Optical launch conditions . 9
4.9 Standard optical test wavelengths . 9
Annex A (informative) Cross-references between new and old test method numbers . 10
Bibliography . 16

Table 1 – Document overview . 6
Table 2 – Standard optical test wavelengths . 9
Table 3 – Alternative optical test wavelengths . 9
Table A.1 – IEC 60794-1-1xx series . 10
Table A.2 – IEC 60794-1-2xx series . 11
Table A.3 – IEC 60794-1-3xx series . 12
Table A.4 – IEC 60794-1-4xx series . 12
Table A.5 – IEC 60794-1-21 method numbers . 12
Table A.6 – IEC 60794-1-22 method numbers . 14
Table A.7 – IEC 60794-1-23 method numbers . 14
Table A.8 – IEC 60794-1-24 method numbers . 15

---------------------- Page: 8 ----------------------
SIST EN IEC 60794-1-2:2021
IEC 60794-1-2:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

OPTICAL FIBRE CABLES –

Part 1-2: Generic specification –
Basic optical cable test procedures –
General guidance

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60794-1-2 has been prepared by subcommittee 86A: Fibres and
cables, of IEC technical committee 86: Fibre optics.
This fifth edition cancels and replaces the fourth edition published in 2017. This edition
constitutes an technical revision.
This edition includes the following significant technical change with respect to the previous
edition:
a) addition of cross-reference tables listing the new test method numbers and the previous test
method numbers.

---------------------- Page: 9 ----------------------
SIST EN IEC 60794-1-2:2021
– 4 – IEC 60794-1-2:2021 © IEC 2021
The text of this International Standard is based on the following documents:
CDV Report on voting
86A/2009/CDV 86A/2057/RVC

Full information on the voting for the approval of this International Standard can be found in the
report on voting indicated in the above table.
This International Standard is to be used in conjunction with IEC 60794-1-1.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 60794 series, published under the general title Optical fibre cables,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to
the specific publication. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 10 ----------------------
SIST EN IEC 60794-1-2:2021
IEC 60794-1-2:2021 © IEC 2021 – 5 –
INTRODUCTION
A decision has been reached to reorganize the IEC 60794-1-2 set of test methods into single-
subject documents. This will be a migration as the existing test methods are revised and as new
test methods are promulgated, rather than a wholesale rewrite. Part of this migration is a
decision to maintain the traditional letter-number classification and to use a numbering system
which maintains connection to the existing numbering system.
The new test method numbering format has been agreed, in line with IEC Secretariat guidelines,
to help the cross-referencing from old to new and that will make the updating of the relevant
sectional and product specifications easier. Cross-reference tables listing the new test method
numbers and the previous test method numbers have been included (see Annex A, Table A.1
to Table A.8).
The format agreed is as follows:
IEC 60794-1-Xnn
where
nd
X = 2 digit of the old 2-digit reference;
nn = incremental number (starting with old test method number).
For example:
IEC 60794-1-21 method E1 (tensile) becomes IEC 60794-1-101;
IEC 60794-1-22 method F5 (water penetration) becomes IEC 60794-1-205;
IEC 60794-1-23 method G7 (tube kinking) becomes IEC 60794-1-307;
IEC 60794-1-24 method H2 (lightning) becomes IEC 60794-1-402.
Annex A has been added to this document containing a cross-reference between the old and
new number scheme.

---------------------- Page: 11 ----------------------
SIST EN IEC 60794-1-2:2021
– 6 – IEC 60794-1-2:2021 © IEC 2021
OPTICAL FIBRE CABLES –

Part 1-2: Generic specification –
Basic optical cable test procedures –
General guidance



1 Scope
This part of IEC 60794-1 applies to optical fibre cables for use with telecommunications
equipment and devices employing similar techniques, and to cables having a combination of
both optical fibres and electrical conductors.
An objective of this document is to define general requirements and methodology guidance
applicable to all of the cable test methods of IEC 60794-1 (all parts).
A second objective of this document is to provide the end user with an overview of the different
test methods contained in the different parts of the IEC 60794-1 series, numbered -Xnn.
Table 1 shows the different parts.
Table 1 – Document overview
Test methods IEC reference Previous Test method category
compendium reference letter
reference
General guidance IEC 60794-1-2 IEC 60794-1-2 -
Mechanical IEC 60794-1-1nn IEC 60794-1-21:2015 Methods E
Environmental IEC 60794-1-2nn IEC 60794-1-22:2017 Methods F
Cable elements IEC 60794-1-3nn IEC 60794-1-23:2019 Methods G
Electrical IEC 60794-1-4nn IEC 60794-1-24:2014 Methods H
NOTE 1 The compendium reference specifications detailed in column 3 will continue in force until all of the test
methods therein are revised into the single-subject documents using the new numbering scheme.
NOTE 2 For existing test methods, "nn" is the test method number. For new test methods, "nn" is an incremental
number following the last test method number for that test category.
NOTE 3 Several numbers in the test method numbering sequence are missing. The reasons for these omissions
are historical. To avoid confusion, the existing numb
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.