SIST EN IEC 60966-1:2019
(Main)Radio frequency and coaxial cable assemblies - Part 1: Generic specification - General requirements and test methods (IEC 60966-1:2019)
Radio frequency and coaxial cable assemblies - Part 1: Generic specification - General requirements and test methods (IEC 60966-1:2019)
This part of IEC 60966 specifies requirements for radio frequency coaxial cable assemblies
operating in the transverse electromagnetic mode (TEM) and establishes general
requirements for testing the electrical, mechanical and environmental properties of radio
frequency coaxial cable assemblies composed of cables and connectors. Additional
requirements relating to specific families of cable assemblies are given in the relevant
sectional specifications.
The design of the cables and connectors used will preferably conform to the applicable parts
of IEC 61196 and IEC 61169 respectively.
NOTE 1 This document does not include tests which are normally performed on the cables and connectors
separately. These tests are described in IEC 61196-1 (all parts) and IEC 61169-1 respectively.
NOTE 2 Wherever possible, cables and connectors used in cable assemblies, even if they are not described in
the IEC 61196 or IEC 61169 series, are tested separately according to the tests given in the relevant generic
specification.
NOTE 3 Where additional protection is applied to a cable assembly, the mechanical and environmental tests
described in this document are applicable.
Konfektionierte Koaxial- und Hochfrequenzkabel - Teil 1: Fachgrundspezifikation - Allgemeine Anforderungen und Prüfverfahren (IEC 60966-1:2019)
Ensembles de cordons coaxiaux et de cordons pour fréquences radioélectriques - Partie 1: Spécification générique - Généralités et méthodes d'essai (IEC 60966-1:2019)
IEC 60966-1:2019 est disponible sous forme de IEC 60966-1:2019 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.
L'IEC 60966-1:2019 définit les exigences relatives aux cordons coaxiaux et aux cordons pour fréquences radioélectriques travaillant en mode électromagnétique transversal (TEM: Transverse Electromagnetic Mode). Elle fixe des exigences générales pour contrôler les propriétés électriques, mécaniques et environnementales des cordons coaxiaux pour fréquences radioélectriques composés de câbles et de connecteurs. Des exigences supplémentaires relatives à des familles spécifiques de cordons figurent dans les spécifications intermédiaires applicables. Cette troisième édition annule et remplace la deuxième édition parue en 1999. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) méthode de mesure de l’efficacité d’écran a été retiree;
b) donne les références aux procédures d'essai applicables pour impedance de transfert and affaiblissement d'écran.
Sestavi radiofrekvenčnih in koaksialnih kablov - 1. del: Splošna specifikacija - Splošne zahteve in preskusne metode (IEC 60966-1:2019)
Ta del standarda IEC 60966 določa zahteve za sestave radiofrekvenčnih koaksialnih kablov, ki delujejo v prečnem elektromagnetnem načinu (TEM), in določa splošne zahteve za preskušanje električnih, mehanskih ter okoljskih lastnosti sestavov radiofrekvenčnih koaksialnih kablov, sestavljenih iz kablov in priključkov. Dodatne zahteve v zvezi s specifičnimi družinami kabelskih sestavov so podane v ustreznih področnih specifikacijah.
Zasnova uporabljenih kablov in priključkov naj bo po možnosti skladna z veljavnimi deli standarda IEC 61196 oziroma IEC 61169.
OPOMBA 1: Ta dokument ne vključuje preskusov, ki se običajno izvajajo ločeno na kablih in priključkih. Ti preskusi so opisani v standardih IEC 61196-1 (vsi deli) in IEC 61169-1.
OPOMBA 2: Če je to mogoče, se preskusi kablov in priključkov, ki se uporabljajo v kabelskih sestavih, tudi če niso opisani v skupini standardov IEC 61196 ali IEC 61169, izvajajo ločeno v skladu s preskusi, podanimi v ustrezni splošni specifikaciji.
OPOMBA 3: Če je na kabelskem sestavu dodatna zaščita, se uporabljajo mehanski in okoljski preskusi, opisani v tem dokumentu.
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 60966-1:2019
01-junij-2019
Nadomešča:
SIST EN 60966-1:2001
Sestavi radiofrekvenčnih in koaksialnih kablov - 1. del: Splošna specifikacija -
Splošne zahteve in preskusne metode (IEC 60966-1:2019)
Radio frequency and coaxial cable assemblies - Part 1: Generic specification - General
requirements and test methods (IEC 60966-1:2019)
Konfektionierte Koaxial- und Hochfrequenzkabel - Teil 1: Fachgrundspezifikation -
Allgemeine Anforderungen und Prüfverfahren (IEC 60966-1:2019)
Ensembles de cordons coaxiaux et de cordons pour fréquences radioélectriques - Partie
1: Spécification générique - Généralités et méthodes d'essai (IEC 60966-1:2019)
Ta slovenski standard je istoveten z: EN IEC 60966-1:2019
ICS:
33.120.10 Koaksialni kabli. Valovodi Coaxial cables. Waveguides
SIST EN IEC 60966-1:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 60966-1:2019
---------------------- Page: 2 ----------------------
SIST EN IEC 60966-1:2019
EUROPEAN STANDARD EN IEC 60966-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2019
ICS 33.120.10 Supersedes EN 60966-1:1999
English Version
Radio frequency and coaxial cable assemblies - Part 1: Generic
specification - General requirements and test methods
(IEC 60966-1:2019)
Cordons coaxiaux et cordons pour fréquences Konfektionierte Koaxial- und Hochfrequenzkabel - Teil 1:
radioélectriques - Partie 1: Spécification générique - Fachgrundspezifikation - Allgemeine Anforderungen und
Exigences générales et méthodes d'essai Prüfverfahren
(IEC 60966-1:2019) (IEC 60966-1:2019)
This European Standard was approved by CENELEC on 2019-03-06. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60966-1:2019 E
---------------------- Page: 3 ----------------------
SIST EN IEC 60966-1:2019
EN IEC 60966-1:2019 (E)
European foreword
The text of document 46/700A/FDIS, future edition 3 of IEC 60966-1, prepared by IEC/TC 46 "Cables,
wires, waveguides, RF connectors, RF and microwave passive components and accessories" was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 60966-1:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2019-12-15
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-03-15
document have to be withdrawn
This document supersedes EN 60966-1:1999.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60966-1:2019 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60339 (series) NOTE Harmonized as HD 350.1 S1 (series)
ISO 9000 NOTE Harmonized as EN ISO 9000
ISO 9001:2015 NOTE Harmonized as EN ISO 9001:2015 (not modified)
2
---------------------- Page: 4 ----------------------
SIST EN IEC 60966-1:2019
EN IEC 60966-1:2019 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068 series Environmental testing EN 60068 series
IEC 60068-2-6 - Environmental testing - Part 2-6: Tests - EN 60068-2-6 -
Test Fc: Vibration (sinusoidal)
IEC 60068-2-11 - Basic environmental testing procedures - EN 60068-2-11 -
Part 2-11: Tests - Test Ka: Salt mist
IEC 60068-2-14 - Environmental testing - Part 2-14: Tests - EN 60068-2-14 -
Test N: Change of temperature
IEC 60068-2-27 - Environmental testing - Part 2-27: Tests - EN 60068-2-27 -
Test Ea and guidance: Shock
IEC 60068-2-42 - Environmental testing - Part 2-42: Tests - EN 60068-2-42 -
Test Kc: Sulphur dioxide test for contacts
and connections
IEC 60068-2-68 - Environmental testing - Part 2-68: Tests - EN 60068-2-68 -
Test L: Dust and sand
IEC 60068-2-78 - Environmental testing - Part 2-78: Tests - EN 60068-2-78 -
Test Cab: Damp heat, steady state
IEC 60332-1-2 2004 Tests on electric and optical fibre cables EN 60332-1-2 2004
under fire conditions - Part 1-2: Test for
vertical flame propagation for a single
insulated wire or cable - Procedure for 1
kW pre-mixed flame
- - + A11 2016
IEC 60512-6-2 - Connectors for electronic equipment - EN 60512-6-2 -
Tests and measurements - Part 6-2:
Dynamic stress tests - Test 6b: Bump
IEC 60512-7-2 - Connectors for electronic equipment - EN 60512-7-2 -
Tests and measurements - Part 7-2:
Impact tests (free components) - Test 7b:
Mechanical strength impact
IEC 60529 - Classification of degrees of protection - -
provided by enclosures
3
---------------------- Page: 5 ----------------------
SIST EN IEC 60966-1:2019
EN IEC 60966-1:2019 (E)
Publication Year Title EN/HD Year
IEC 60966-2 series Radio frequency and coaxial cable EN 60966-2 series
assemblies
IEC 60966-3 series Radio frequency and coaxial cable EN 60966-3 series
assemblies
IEC 60966-4 series Radio frequency and coaxial cable EN 60966-4 series
assemblies
IEC 61169 series Radio frequency connectors EN 61169 series
IEC 61169-1 2013 Radio frequency connectors - Part 1: EN 61169-1 2013
Generic specification - General
requirements and measuring methods
IEC 61196 series Coaxial communication cables - series
IEC 61196-1-119 - Coaxial communication cables - Part 1- - -
119: Electrical test methods - RF power
rating
IEC 62037-2 - Passive RF and microwave devices, EN 62037-2 -
intermodulation level measurement - Part
2: Measurement of passive intermodulation
in coaxial cable assemblies
IEC 62153-4-6 - Metallic cables and other passive - -
components test methods - Part 4-6:
Electromagnetic compatibility (EMC) -
Surface transfer impedance - line injection
method
IEC 62153-4-7 2015 Metallic communication cable test methods EN 62153-4-7 2016
– Part 4-7: Electromagnetic compatibility
(EMC) – Test method for measuring of
transfer impedance Z and screening
T
attenuation a or coupling attenuation a
s C
of connectors and assemblies up to and
above 3 GHz – Triaxial tube in tube
method
4
---------------------- Page: 6 ----------------------
SIST EN IEC 60966-1:2019
IEC 60966-1
®
Edition 3.0 2019-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Radio frequency and coaxial cable assemblies –
Part 1: Generic specification – General requirements and test methods
Cordons coaxiaux et cordons pour fréquences radioélectriques –
Partie 1: Spécification générique – Exigences générales et méthodes d’essai
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.10 ISBN 978-2-8322-6259-7
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 60966-1:2019
– 2 – IEC 60966-1:2019 © IEC 2019
CONTENTS
FOREWORD . 7
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 10
4 Design and manufacturing requirements . 12
4.1 Cable design and construction . 12
4.2 Connector design and construction . 12
4.3 Outline and interface dimensions . 13
5 Workmanship, marking and packaging . 13
5.1 Workmanship . 13
5.2 Marking . 13
5.3 End caps. 13
5.4 Packaging and labelling . 13
6 Quality management . 13
7 Test methods – General . 13
7.1 Standard atmospheric conditions for testing . 13
7.2 Visual inspection . 14
7.3 Dimensions inspection . 14
7.3.1 Interface dimensions . 14
7.3.2 Outline dimensions . 14
8 Electrical tests . 15
8.1 Reflection properties . 15
8.1.1 Object . 15
8.1.2 Test equipment . 15
8.1.3 Procedure . 15
8.1.4 Requirements . 16
8.1.5 Information to be given in the detail specification . 16
8.2 Uniformity of impedance . 16
8.2.1 Object . 16
8.2.2 Procedure . 16
8.2.3 Requirements . 16
8.2.4 Information to be given in the detail specification . 16
8.3 Insertion loss . 16
8.3.1 Procedure . 16
8.3.2 Requirements . 16
8.3.3 Information to be given in the detail specification . 16
8.4 Insertion loss stability . 17
8.4.1 Object . 17
8.4.2 Procedure . 17
8.4.3 Requirements . 17
8.4.4 Information to be given in the detail specification . 17
8.5 Propagation time . 17
8.5.1 Procedure . 17
8.5.2 Requirements . 17
8.5.3 Information to be given in the detail specification . 17
---------------------- Page: 8 ----------------------
SIST EN IEC 60966-1:2019
IEC 60966-1:2019 © IEC 2019 – 3 –
8.6 Stability of electrical length . 17
8.6.1 Object . 17
8.6.2 Procedures . 17
8.6.3 Requirements . 19
8.6.4 Information to be given in the detail specification . 19
8.7 Phase difference . 19
8.7.1 Object . 19
8.7.2 Procedure . 19
8.7.3 Requirements . 19
8.7.4 Information to be given in the detail specification . 20
8.8 Phase variation with temperature . 20
8.8.1 Object . 20
8.8.2 Procedure . 20
8.8.3 Requirements . 20
8.8.4 Information to be given in the detail specification . 20
8.9 Screening effectiveness . 20
8.9.1 Transfer impedance . 20
8.9.2 Screening attenuation . 20
8.10 Voltage proof . 21
8.10.1 Procedure . 21
8.10.2 Requirements . 21
8.10.3 Information to be given in the detail specification . 21
8.11 Insulation resistance . 21
8.11.1 Procedure . 21
8.11.2 Requirements . 21
8.11.3 Information to be given in the detail specification . 21
8.12 Inner and outer conductor continuity . 22
8.12.1 Object . 22
8.12.2 Procedure . 22
8.12.3 Requirements . 22
8.12.4 Information to be given in the detail specification . 22
8.13 Power rating . 22
8.13.1 Object . 22
8.13.2 Procedure . 22
8.13.3 Requirements . 22
8.13.4 Information to be given in the detail specification . 22
8.14 Intermodulation level measurement . 23
8.14.1 Procedure . 23
8.14.2 Requirements . 23
8.14.3 Information to be given in the detail specification . 23
9 Mechanical robustness tests . 23
9.1 Tensile . 23
9.1.1 Object . 23
9.1.2 Procedure . 23
9.1.3 Requirements . 23
9.1.4 Information to be given in the detail specification . 23
9.2 Flexure . 24
9.2.1 Object . 24
9.2.2 Procedure . 24
---------------------- Page: 9 ----------------------
SIST EN IEC 60966-1:2019
– 4 – IEC 60966-1:2019 © IEC 2019
9.2.3 Requirements . 24
9.2.4 Information to be given in the detail specification . 24
9.3 Flexing endurance . 24
9.3.1 Object . 24
9.3.2 Procedure . 25
9.3.3 Requirements . 25
9.3.4 Information to be given in the detail specification . 25
9.4 Cable assembly crushing . 25
9.4.1 Object . 25
9.4.2 Procedure . 25
9.4.3 Requirements . 26
9.4.4 Information to be given in the detail specification . 26
9.5 Torque . 26
9.5.1 Procedure . 26
9.5.2 Requirements . 27
9.5.3 Information to be given in the detail specification . 27
9.6 Multiple bending. 27
9.6.1 Object . 27
9.6.2 Procedure . 27
9.6.3 Requirements . 28
9.6.4 Information to be given in the detail specification . 28
9.7 Abrasion test of cable assembly . 28
9.7.1 Object . 28
9.7.2 Procedure . 28
9.8 Vibrations, shocks . 28
9.9 Impact test . 28
9.10 Mechanical endurance . 28
10 Environmental tests . 29
10.1 Recommended severities . 29
10.2 Vibration, bumps and shock . 29
10.3 Climatic sequence. 29
10.3.1 Procedure . 29
10.3.2 Requirements . 29
10.3.3 Information to be given in the detail specification . 29
10.4 Damp heat, steady state . 29
10.4.1 Procedure . 29
10.4.2 Requirements . 29
10.4.3 Information to be given in the detail specification . 30
10.5 Rapid change of temperature . 30
10.5.1 Procedure . 30
10.5.2 Requirements . 30
10.5.3 Information to be given in the detail specification . 30
10.6 Resistance to solvents and contaminating fluids . 30
10.6.1 Procedure . 30
10.6.2 Requirements . 30
10.6.3 Information to be given in the detail specification . 31
10.7 Water immersion . 31
10.7.1 Procedure . 31
10.7.2 Requirements . 31
---------------------- Page: 10 ----------------------
SIST EN IEC 60966-1:2019
IEC 60966-1:2019 © IEC 2019 – 5 –
10.7.3 Information to be given in the detail specification . 31
10.8 Salt mist and sulphur dioxide tests . 31
10.8.1 Procedure . 31
10.8.2 Requirements . 31
10.8.3 Information to be given in the detail specification . 31
10.9 Dust tests . 31
10.9.1 Object . 31
10.9.2 Procedure . 31
10.9.3 Requirements . 32
10.9.4 Information to be given in the detail specification . 32
10.10 Flammability . 32
10.10.1 Procedure . 32
10.10.2 Requirements . 32
10.10.3 Information to be given in the detail specification . 32
11 Specialized test methods . 32
12 Test schedules . 32
Annex A (normative) Test methods for insertion loss determination . 33
A.1 Purpose . 33
A.2 Test methods . 33
A.2.1 General . 33
A.2.2 Test method 1 . 33
A.2.3 Test method 2 . 34
A.2.4 Test method 3 .
...
SLOVENSKI STANDARD
SIST EN IEC 60966-1:2019
01-junij-2019
Nadomešča:
SIST EN 60966-1:2001
Radijska frekvenca in sestavi koaksialnih kablov - 1. del: Splošna specifikacija -
Splošne zahteve in preskusne metode (IEC 60966-1:2019)
Radio frequency and coaxial cable assemblies - Part 1: Generic specification - General
requirements and test methods (IEC 60966-1:2019)
Konfektionierte Koaxial- und Hochfrequenzkabel - Teil 1: Fachgrundspezifikation -
Allgemeine Anforderungen und Prüfverfahren (IEC 60966-1:2019)
Ensembles de cordons coaxiaux et de cordons pour fréquences radioélectriques - Partie
1: Spécification générique - Généralités et méthodes d'essai (IEC 60966-1:2019)
Ta slovenski standard je istoveten z: EN IEC 60966-1:2019
ICS:
33.120.10 Koaksialni kabli. Valovodi Coaxial cables. Waveguides
SIST EN IEC 60966-1:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 60966-1:2019
---------------------- Page: 2 ----------------------
SIST EN IEC 60966-1:2019
EUROPEAN STANDARD EN IEC 60966-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2019
ICS 33.120.10 Supersedes EN 60966-1:1999
English Version
Radio frequency and coaxial cable assemblies - Part 1: Generic
specification - General requirements and test methods
(IEC 60966-1:2019)
Cordons coaxiaux et cordons pour fréquences Konfektionierte Koaxial- und Hochfrequenzkabel - Teil 1:
radioélectriques - Partie 1: Spécification générique - Fachgrundspezifikation - Allgemeine Anforderungen und
Exigences générales et méthodes d'essai Prüfverfahren
(IEC 60966-1:2019) (IEC 60966-1:2019)
This European Standard was approved by CENELEC on 2019-03-06. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60966-1:2019 E
---------------------- Page: 3 ----------------------
SIST EN IEC 60966-1:2019
EN IEC 60966-1:2019 (E)
European foreword
The text of document 46/700A/FDIS, future edition 3 of IEC 60966-1, prepared by IEC/TC 46 "Cables,
wires, waveguides, RF connectors, RF and microwave passive components and accessories" was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 60966-1:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2019-12-15
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-03-15
document have to be withdrawn
This document supersedes EN 60966-1:1999.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60966-1:2019 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60339 (series) NOTE Harmonized as HD 350.1 S1 (series)
ISO 9000 NOTE Harmonized as EN ISO 9000
ISO 9001:2015 NOTE Harmonized as EN ISO 9001:2015 (not modified)
2
---------------------- Page: 4 ----------------------
SIST EN IEC 60966-1:2019
EN IEC 60966-1:2019 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068 series Environmental testing EN 60068 series
IEC 60068-2-6 - Environmental testing - Part 2-6: Tests - EN 60068-2-6 -
Test Fc: Vibration (sinusoidal)
IEC 60068-2-11 - Basic environmental testing procedures - EN 60068-2-11 -
Part 2-11: Tests - Test Ka: Salt mist
IEC 60068-2-14 - Environmental testing - Part 2-14: Tests - EN 60068-2-14 -
Test N: Change of temperature
IEC 60068-2-27 - Environmental testing - Part 2-27: Tests - EN 60068-2-27 -
Test Ea and guidance: Shock
IEC 60068-2-42 - Environmental testing - Part 2-42: Tests - EN 60068-2-42 -
Test Kc: Sulphur dioxide test for contacts
and connections
IEC 60068-2-68 - Environmental testing - Part 2-68: Tests - EN 60068-2-68 -
Test L: Dust and sand
IEC 60068-2-78 - Environmental testing - Part 2-78: Tests - EN 60068-2-78 -
Test Cab: Damp heat, steady state
IEC 60332-1-2 2004 Tests on electric and optical fibre cables EN 60332-1-2 2004
under fire conditions - Part 1-2: Test for
vertical flame propagation for a single
insulated wire or cable - Procedure for 1
kW pre-mixed flame
- - + A11 2016
IEC 60512-6-2 - Connectors for electronic equipment - EN 60512-6-2 -
Tests and measurements - Part 6-2:
Dynamic stress tests - Test 6b: Bump
IEC 60512-7-2 - Connectors for electronic equipment - EN 60512-7-2 -
Tests and measurements - Part 7-2:
Impact tests (free components) - Test 7b:
Mechanical strength impact
IEC 60529 - Classification of degrees of protection - -
provided by enclosures
3
---------------------- Page: 5 ----------------------
SIST EN IEC 60966-1:2019
EN IEC 60966-1:2019 (E)
Publication Year Title EN/HD Year
IEC 60966-2 series Radio frequency and coaxial cable EN 60966-2 series
assemblies
IEC 60966-3 series Radio frequency and coaxial cable EN 60966-3 series
assemblies
IEC 60966-4 series Radio frequency and coaxial cable EN 60966-4 series
assemblies
IEC 61169 series Radio frequency connectors EN 61169 series
IEC 61169-1 2013 Radio frequency connectors - Part 1: EN 61169-1 2013
Generic specification - General
requirements and measuring methods
IEC 61196 series Coaxial communication cables - series
IEC 61196-1-119 - Coaxial communication cables - Part 1- - -
119: Electrical test methods - RF power
rating
IEC 62037-2 - Passive RF and microwave devices, EN 62037-2 -
intermodulation level measurement - Part
2: Measurement of passive intermodulation
in coaxial cable assemblies
IEC 62153-4-6 - Metallic cables and other passive - -
components test methods - Part 4-6:
Electromagnetic compatibility (EMC) -
Surface transfer impedance - line injection
method
IEC 62153-4-7 2015 Metallic communication cable test methods EN 62153-4-7 2016
– Part 4-7: Electromagnetic compatibility
(EMC) – Test method for measuring of
transfer impedance Z and screening
T
attenuation a or coupling attenuation a
s C
of connectors and assemblies up to and
above 3 GHz – Triaxial tube in tube
method
4
---------------------- Page: 6 ----------------------
SIST EN IEC 60966-1:2019
IEC 60966-1
®
Edition 3.0 2019-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Radio frequency and coaxial cable assemblies –
Part 1: Generic specification – General requirements and test methods
Cordons coaxiaux et cordons pour fréquences radioélectriques –
Partie 1: Spécification générique – Exigences générales et méthodes d’essai
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.10 ISBN 978-2-8322-6259-7
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 60966-1:2019
– 2 – IEC 60966-1:2019 © IEC 2019
CONTENTS
FOREWORD . 7
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 10
4 Design and manufacturing requirements . 12
4.1 Cable design and construction . 12
4.2 Connector design and construction . 12
4.3 Outline and interface dimensions . 13
5 Workmanship, marking and packaging . 13
5.1 Workmanship . 13
5.2 Marking . 13
5.3 End caps. 13
5.4 Packaging and labelling . 13
6 Quality management . 13
7 Test methods – General . 13
7.1 Standard atmospheric conditions for testing . 13
7.2 Visual inspection . 14
7.3 Dimensions inspection . 14
7.3.1 Interface dimensions . 14
7.3.2 Outline dimensions . 14
8 Electrical tests . 15
8.1 Reflection properties . 15
8.1.1 Object . 15
8.1.2 Test equipment . 15
8.1.3 Procedure . 15
8.1.4 Requirements . 16
8.1.5 Information to be given in the detail specification . 16
8.2 Uniformity of impedance . 16
8.2.1 Object . 16
8.2.2 Procedure . 16
8.2.3 Requirements . 16
8.2.4 Information to be given in the detail specification . 16
8.3 Insertion loss . 16
8.3.1 Procedure . 16
8.3.2 Requirements . 16
8.3.3 Information to be given in the detail specification . 16
8.4 Insertion loss stability . 17
8.4.1 Object . 17
8.4.2 Procedure . 17
8.4.3 Requirements . 17
8.4.4 Information to be given in the detail specification . 17
8.5 Propagation time . 17
8.5.1 Procedure . 17
8.5.2 Requirements . 17
8.5.3 Information to be given in the detail specification . 17
---------------------- Page: 8 ----------------------
SIST EN IEC 60966-1:2019
IEC 60966-1:2019 © IEC 2019 – 3 –
8.6 Stability of electrical length . 17
8.6.1 Object . 17
8.6.2 Procedures . 17
8.6.3 Requirements . 19
8.6.4 Information to be given in the detail specification . 19
8.7 Phase difference . 19
8.7.1 Object . 19
8.7.2 Procedure . 19
8.7.3 Requirements . 19
8.7.4 Information to be given in the detail specification . 20
8.8 Phase variation with temperature . 20
8.8.1 Object . 20
8.8.2 Procedure . 20
8.8.3 Requirements . 20
8.8.4 Information to be given in the detail specification . 20
8.9 Screening effectiveness . 20
8.9.1 Transfer impedance . 20
8.9.2 Screening attenuation . 20
8.10 Voltage proof . 21
8.10.1 Procedure . 21
8.10.2 Requirements . 21
8.10.3 Information to be given in the detail specification . 21
8.11 Insulation resistance . 21
8.11.1 Procedure . 21
8.11.2 Requirements . 21
8.11.3 Information to be given in the detail specification . 21
8.12 Inner and outer conductor continuity . 22
8.12.1 Object . 22
8.12.2 Procedure . 22
8.12.3 Requirements . 22
8.12.4 Information to be given in the detail specification . 22
8.13 Power rating . 22
8.13.1 Object . 22
8.13.2 Procedure . 22
8.13.3 Requirements . 22
8.13.4 Information to be given in the detail specification . 22
8.14 Intermodulation level measurement . 23
8.14.1 Procedure . 23
8.14.2 Requirements . 23
8.14.3 Information to be given in the detail specification . 23
9 Mechanical robustness tests . 23
9.1 Tensile . 23
9.1.1 Object . 23
9.1.2 Procedure . 23
9.1.3 Requirements . 23
9.1.4 Information to be given in the detail specification . 23
9.2 Flexure . 24
9.2.1 Object . 24
9.2.2 Procedure . 24
---------------------- Page: 9 ----------------------
SIST EN IEC 60966-1:2019
– 4 – IEC 60966-1:2019 © IEC 2019
9.2.3 Requirements . 24
9.2.4 Information to be given in the detail specification . 24
9.3 Flexing endurance . 24
9.3.1 Object . 24
9.3.2 Procedure . 25
9.3.3 Requirements . 25
9.3.4 Information to be given in the detail specification . 25
9.4 Cable assembly crushing . 25
9.4.1 Object . 25
9.4.2 Procedure . 25
9.4.3 Requirements . 26
9.4.4 Information to be given in the detail specification . 26
9.5 Torque . 26
9.5.1 Procedure . 26
9.5.2 Requirements . 27
9.5.3 Information to be given in the detail specification . 27
9.6 Multiple bending. 27
9.6.1 Object . 27
9.6.2 Procedure . 27
9.6.3 Requirements . 28
9.6.4 Information to be given in the detail specification . 28
9.7 Abrasion test of cable assembly . 28
9.7.1 Object . 28
9.7.2 Procedure . 28
9.8 Vibrations, shocks . 28
9.9 Impact test . 28
9.10 Mechanical endurance . 28
10 Environmental tests . 29
10.1 Recommended severities . 29
10.2 Vibration, bumps and shock . 29
10.3 Climatic sequence. 29
10.3.1 Procedure . 29
10.3.2 Requirements . 29
10.3.3 Information to be given in the detail specification . 29
10.4 Damp heat, steady state . 29
10.4.1 Procedure . 29
10.4.2 Requirements . 29
10.4.3 Information to be given in the detail specification . 30
10.5 Rapid change of temperature . 30
10.5.1 Procedure . 30
10.5.2 Requirements . 30
10.5.3 Information to be given in the detail specification . 30
10.6 Resistance to solvents and contaminating fluids . 30
10.6.1 Procedure . 30
10.6.2 Requirements . 30
10.6.3 Information to be given in the detail specification . 31
10.7 Water immersion . 31
10.7.1 Procedure . 31
10.7.2 Requirements . 31
---------------------- Page: 10 ----------------------
SIST EN IEC 60966-1:2019
IEC 60966-1:2019 © IEC 2019 – 5 –
10.7.3 Information to be given in the detail specification . 31
10.8 Salt mist and sulphur dioxide tests . 31
10.8.1 Procedure . 31
10.8.2 Requirements . 31
10.8.3 Information to be given in the detail specification . 31
10.9 Dust tests . 31
10.9.1 Object . 31
10.9.2 Procedure . 31
10.9.3 Requirements . 32
10.9.4 Information to be given in the detail specification . 32
10.10 Flammability . 32
10.10.1 Procedure . 32
10.10.2 Requirements . 32
10.10.3 Information to be given in the detail specification . 32
11 Specialized test methods . 32
12 Test schedules . 32
Annex A (normative) Test methods for insertion loss determination . 33
A.1 Purpose . 33
A.2 Test methods . 33
A.2.1 General . 33
A.2.2 Test method 1 . 33
A.2.3 Test method 2 . 34
A.2.4 Test method 3 .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.