Thermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying

This European Standard specifies the processing of surface preparation for thermal spraying. Important principles indicated in this European Standard should be taken into consideration when surfaces of metallic parts are to be prepared for thermal spraying. This European Standard applies for production of new parts as well as for the repair of worn parts.
This European Standard does not apply for thermal spraying in the case of protection against atmospheric corrosion by coatings of zinc and/or aluminium and their alloys, for which prEN ISO 2063 1:2014 and prEN ISO 2063 2:2014 apply.

Thermisches Spritzen - Vorbehandlung von Oberflächen metallischer Werkstücke und Bauteile für das thermische Spritzen

Dieses Dokument legt die Vorgehensweise zur Vorbereitung von Oberflächen zum thermischen Spritzen fest. Es ist vorgesehen, dass die in dieser Europäischen Norm angegebenen wichtigen Grundsätze beim Vorbereiten von Oberflächen metallischer Bauteile zum thermischen Spritzen berücksichtigt werden. Dieses Dokument gilt sowohl für die Neufertigung als auch für das Instandsetzen verschlissener Teile.
Dieses Dokument gilt nicht für das thermische Spritzen zum Schutz gegen atmosphärische Korrosion durch Schichten aus Zink und/oder Aluminium und deren Legierungen, dafür gelten EN ISO 2063-1:2017 und EN ISO 2063-2:2017.

Projection thermique - Traitement préalable de surface de pièces et composants métalliques pour projection thermiques

Le présent document spécifie les opérations associées à la préparation des surfaces destinées à recevoir un revêtement appliqué par projection thermique. Les principes importants indiqués dans la présente Norme européenne doivent être pris en considération lors de la préparation des surfaces métalliques destinées à être soumises à l'opération de projection thermique. Le présent document s’applique à la fois à la production de nouvelles pièces et à la réparation de pièces usées.
Le présent document ne s'applique pas à la projection thermique en cas de protection contre la corrosion atmosphérique par des revêtements de zinc et/ou d’aluminium et leurs alliages, pour lesquels EN ISO 2063‐1:2017 et EN ISO 2063‐2:2017 sont applicables.

Vroče brizganje - Predobdelava površin kovinskih delov in komponent za vroče brizganje

Ta evropski standard določa obdelavo priprave površin za vroče brizganje. Pri pripravi površin kovinskih delov za vroče brizganje je treba upoštevati pomembna načela v tem evropskem standardu. Ta evropski standard se uporablja tako za proizvodnjo novih delov kot popravilo obrabljenih delov.
Ta evropski standard se ne uporablja za vroče brizganje kot zaščito pred atmosfersko korozijo s premazi iz cinka in/ali aluminija ter njunih zlitin, za kar se uporabljata standarda prEN ISO 2063 1:2014 in prEN ISO 2063 2:2014.

General Information

Status
Published
Public Enquiry End Date
09-Aug-2016
Publication Date
11-Nov-2018
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
17-Oct-2018
Due Date
22-Dec-2018
Completion Date
12-Nov-2018

Relations

Buy Standard

Standard
EN 13507:2018
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.EUL]JDQMHThermisches Spritzen - Vorbehandlung von Oberflächen metallischer Werkstücke und Bauteile für das thermische SpritzenProjection thermique - Traitement préalable de surface de pièces et composants métalliques pour projection thermiquesThermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying25.220.20Površinska obdelavaSurface treatment25.220.10Priprava površineSurface preparationICS:Ta slovenski standard je istoveten z:EN 13507:2018SIST EN 13507:2018en,fr,de01-december-2018SIST EN 13507:2018SLOVENSKI
STANDARDSIST EN 13507:20101DGRPHãþD



SIST EN 13507:2018



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13507
August
t r s z ICS
t wä t t rä s râ
t wä t t rä t r Supersedes EN
s u w r yã t r s rEnglish Version
Thermal spraying æ Preætreatment of surfaces of metallic parts and components for thermal spraying Projection thermique æ Traitement préalable de surface de pièces et composants métalliques pour projection thermiques
Thermisches Spritzen æ Vorbehandlung von Oberflächen metallischer Werkstücke und Bauteile für das thermische Spritzen This European Standard was approved by CEN on
{ April
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u w r yã t r s z ESIST EN 13507:2018



EN 13507:2018 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Principles . 4 5 Methods of surface preparation . 5 5.1 General . 5 5.2 Degreasing . 5 5.3 Grit blasting . 5 5.3.1 Cleanliness . 5 5.3.2 Roughness . 6 5.3.3 Abrasives . 6 5.3.4 Post cleaning after grit blasting . 6 5.3.5 Examination of grit blasted surfaces . 7 5.4 Threading/grooving . 7 5.5 Cleaning by reversed transferred arc . 7 5.6 Bond coatings . 7 5.7 Precautions for health, safety and environmental protection . 7 6 Preheating . 7 7 Masking of areas not to be coated . 8 8 Effect of pre-treatment on the fatigue strength . 8 Bibliography . 9 SIST EN 13507:2018



EN 13507:2018 (E) 3 European foreword This document (EN 13507:2018) has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed coatings”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2019, and conflicting national standards shall be withdrawn at the latest by February 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13507:2010. This third edition of EN 13507 cancels and replaces EN 13507:2010, which has been technically revised and, in addition to the change in number, contains the following changes: — update of normative references; — Revision of subclause 5.6 (Bond coatings). According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 13507:2018



EN 13507:2018 (E) 4 1 Scope This document specifies the processing of surface preparation for thermal spraying. Important principles indicated in this European Standard are intended to be taken into consideration when surfaces of metallic parts are to be prepared for thermal spraying. This document applies for production of new parts as well as for the repair of worn parts. This document does not apply for thermal spraying in the case of protection against atmospheric corrosion by coatings of zinc and/or aluminium and their alloys, for which EN ISO 2063-1:2017 and EN ISO 2063-2:2017 apply. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 8501-1, Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings (ISO 8501-1) EN ISO 11124-1, Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 1: General introduction and classification (ISO 11124-1) EN ISO 11124-2, Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 2: Chilled-iron grit (ISO 11124-2) EN ISO 11126-1, Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 1: General introduction and classification (ISO 11126-1) 3 Terms and definitions No terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in standardization at the following addresses:
IEC Electropedia: available at http://www.electropedia.org/
ISO Online browsing platform: available at http://www.iso.org/obp 4 Principles The surface preparation of a work piece has a substantial effect on the quality of the sprayed coating especially with regard to its adhesion to the substrate. To achieve a sufficient adhesive strength the metallic surface shall be processed until a technically clean interface is generated. The surface to be prepared shall be accessible for grit blasting. EN 15520 gives information regarding suitable component design. Welding splashes and residues of welding slag shall be removed, and weld seams and brazed or soldered joints shall be prepared with particular accuracy. Oxides, oil, grease and other contamination shall be removed. SIST EN 13507:2018



EN 13507:2018 (E) 5 The roughness of the surface shall enable a good interlocking of the sprayed coating to the substrate. Grit blasting is a suitable method for obtaining appropriate roughened metallic surfaces, thereby also enlarging the effective area. The surface to be sprayed shall be kept dry during the preparation and spraying process. For outdoor spraying this requirement shall be met by taking suitable precautions. The prepared surface shall be coated subsequently after carrying out the grit blasting without any undue loss of time1). 5 Methods of surface preparation 5.1 General Depending upon the function of the sprayed coating and the initial condition of the surface, different preparation procedures are used. In any case scale, rust, dust and other contaminants shall be removed by mechanical cleaning. 5.2 Degreasing Oil and grease contaminants shall be removed thoroughly prior to processing the surface. In particular attention shall be given to bores, slots and channels. Design of components shall be such that fluids can drain out. Degreasing can be done by heating, dipping and spraying processes with or without additional mechanical support by ultrasonic cleaning, brushing or steam jet blower. Aqueous wash solutions or organic solvents are suitable. For the application of wash solutions a mild alkaline cleaner with a high content of surfactants may be preferred. Whenever possible cleaner free of phosphate should be used. The application of chlorinated or fluorinated hydrocarbons should be avoided due to their detrimental effect on health and the environment. Subsequent rinsing and drying is necessary. For health, safety and environment aspects see 5.7. 5.3 Grit blasting 5.3.1 Cleanliness For thermal spraying the surface shall be sufficiently cleaned and roughened by applying a suitable grit. The grit blasting process shall be continued until the area to be coated shows a metallic surface with a uniform structure according to EN ISO 8501-1 Sa 3. Unwanted loss of material, which can occur by excessive blasting, shall be considered. Generally, the preparation grade Sa 3 is necessary but often not sufficient for the purpose. I
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.