Satellite Earth Stations and Systems (SES) - Harmonized EN for Satellite Interactive Terminals (SIT) and Satellite User Terminals (SUT) transmitting towards satellites in geostationary orbit in the 29,5 GHz to 30,0 GHz frequency bands covering essential requirements under article 3.2 of the R&TTE Directive

The present document applies to Satellite Interactive Terminals (SIT) and Satellite User Terminals (SUT) operating as part of a bi-directional satellite network. Satellite Terminal (ST) is used in the present document as a generic name that refers equally to a SIT and/or a SUT. In such a network a Network Control Facility (NCF) is responsible for the monitoring and control of the transmit functions of the STs. These STs have the following characteristics:
• in the case of SITs reception is in the Fixed Satellite Service (FSS) frequency ranges from 10,70 GHz to 11,70 GHz and from 12,50 GHz to 12,75 GHz, as well as the Broadcast Satellite Service (BSS) frequency range from 11,70 GHz to 12,50 GHz;
• in the case of SUTs reception is in the Fixed Satellite Service (FSS) frequency ranges from 19,70 GHz to 20,20 GHz and from 17,70 GHz to 19,70 GHz, as well as the Broadcast Satellite Service (BSS) frequency range from 21,40 GHz to 22,00 GHz;
• in all cases ST transmission is in the frequency band allocated to FSS on a primary basis from 29,5 GHz to 30,0 GHz;
• STs transmit towards geostationary satellites with spacing down to 2° away from any other geostationary satellite operating in the same frequency band and covering the same area;
• linear or circular polarization is used for transmission or reception;
• the received signals may be analogue and/or digital;
• the transmitted signals are always of digital nature;
• the ST antenna diameter does not exceed 1,8 m, or equivalent effective area;
• the ST is designed for unattended operations.
The equipment considered in the present document comprises both the outdoor unit, usually composed of the antenna subsystem and associated upconverter, power amplifier and Low Noise Block (LNB) downconverter, and the indoor unit, usually composed of receive and transmit logic as well as the modulator, including cables between these two units. The present document applies to the ST with its ancillary equipment and its various ports and when operated within the boundary limits of all the operational environmental profile declared by the applicant and when installed as required by the applicant by declaration or in the user documentation. All parts of the indoor unit related to reception, processing and presentation of the received information except the control channel are not within the scope of the present document. The syntax of the control channel messages is outside the scope of the present document. The present document is intended to cover the provisions of Directive 1999/5/EC [2] (R&TTE Directive) article 3.2, which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [2] may apply to equipment within the scope of the present document.

Satelitske zemeljske postaje in sistemi (SES) - Harmonizirani EN za satelitske interaktivne terminale (SIT) in satelitske uporabniške terminale (SUT), ki oddajajo proti satelitom v geostacionarni orbiti v frekvenčnih pasovih od 29,5 GHz do 30,0 GHz, ki zajema bistvene zahteve člena 3.2 direktive R&TTE

General Information

Status
Published
Publication Date
06-Nov-2007
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
05-Nov-2007
Due Date
10-Jan-2008
Completion Date
07-Nov-2007
Mandate

Relations

Buy Standard

Standard
EN 301 459 V1.4.1:2007
English language
49 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 301 459 V1.4.1:2007
01-december-2007
6DWHOLWVNH]HPHOMVNHSRVWDMHLQVLVWHPL 6(6 +DUPRQL]LUDQL(1]DVDWHOLWVNH
LQWHUDNWLYQHWHUPLQDOH 6,7 LQVDWHOLWVNHXSRUDEQLãNHWHUPLQDOH 687 NLRGGDMDMR
SURWLVDWHOLWRPYJHRVWDFLRQDUQLRUELWLYIUHNYHQþQLKSDVRYLKRG*+]GR
*+]NL]DMHPDELVWYHQH]DKWHYHþOHQDGLUHNWLYH5 77(
Satellite Earth Stations and Systems (SES) - Harmonized EN for Satellite Interactive
Terminals (SIT) and Satellite User Terminals (SUT) transmitting towards satellites in
geostationary orbit in the 29,5 GHz to 30,0 GHz frequency bands covering essential
requirements under article 3.2 of the R&TTE Directive
Ta slovenski standard je istoveten z: EN 301 459 Version 1.4.1
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
SIST EN 301 459 V1.4.1:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 301 459 V1.4.1:2007

---------------------- Page: 2 ----------------------

SIST EN 301 459 V1.4.1:2007

ETSI EN 301 459 V1.4.1 (2007-06)
Harmonized European Standard (Telecommunications series)

Satellite Earth Stations and Systems (SES);
Harmonized EN for Satellite Interactive Terminals (SIT)
and Satellite User Terminals (SUT)
transmitting towards satellites in geostationary orbit
in the 29,5 GHz to 30,0 GHz frequency bands
covering essential requirements
under article 3.2 of the R&TTE Directive

---------------------- Page: 3 ----------------------

SIST EN 301 459 V1.4.1:2007
 2 ETSI EN 301 459 V1.4.1 (2007-06)



Reference
REN/SES-00282
Keywords
FSS, BSS, earth station, regulation, satellite,
terminal
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2007.
All rights reserved.

TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI

---------------------- Page: 4 ----------------------

SIST EN 301 459 V1.4.1:2007
 3 ETSI EN 301 459 V1.4.1 (2007-06)
Contents
Intellectual Property Rights.6
Foreword.6
Introduction .7
1 Scope.8
2 References.9
3 Definitions and abbreviations.9
3.1 Definitions.9
3.2 Abbreviations.11
4 Technical requirements specifications.12
4.1 General.12
4.1.1 Environmental profile.12
4.1.2 ST states and radio states .12
4.2 Conformance requirements.13
4.2.1 General.13
4.2.2 Off-axis spurious radiation .13
4.2.2.1 Purpose.13
4.2.2.2 Specification.13
4.2.2.3 Conformance tests.14
4.2.3 On-axis spurious radiation .14
4.2.3.1 Purpose.14
4.2.3.2 Specification.15
4.2.3.2.1 "Carrier-on" radio state.15
4.2.3.2.2 "Carrier-off" and "Emissions disabled" radio states.15
4.2.3.3 Conformance tests.15
4.2.4 Off-axis e.i.r.p. emission density within the band.15
4.2.4.1 Purpose.15
4.2.4.2 Specification.16
4.2.4.3 Conformance tests.17
4.2.5 Carrier suppression.17
4.2.5.1 Purpose.17
4.2.5.2 Specification.17
4.2.5.3 Conformance tests.17
4.2.6 Antenna pointing accuracy .18
4.2.6.1 Purpose.18
4.2.6.2 Specification.18
4.2.6.3 Conformance tests.18
4.2.7 Control and Monitoring Functions (CMF).18
4.2.7.1 General.18
4.2.7.2 Processor monitoring.19
4.2.7.2.1 Purpose.19
4.2.7.2.2 Specification.19
4.2.7.2.3 Conformance tests.20
4.2.7.3 Transmit subsystem monitoring.20
4.2.7.3.1 Purpose.20
4.2.7.3.2 Specification.20
4.2.7.3.3 Conformance tests.20
4.2.7.4 Power-on/Reset.20
4.2.7.4.1 Purpose.20
4.2.7.4.2 Specification.20
4.2.7.4.3 Conformance tests.20
4.2.7.5 Control Channel (CC) reception .20
4.2.7.5.1 Purpose.20
4.2.7.5.2 Specification.20
ETSI

---------------------- Page: 5 ----------------------

SIST EN 301 459 V1.4.1:2007
 4 ETSI EN 301 459 V1.4.1 (2007-06)
4.2.7.5.3 Conformance tests.21
4.2.7.6 Network control commands .21
4.2.7.6.1 Purpose.21
4.2.7.6.2 Specification.21
4.2.7.6.3 Conformance test.21
4.2.7.7 Initial burst transmission .21
4.2.7.7.1 Purpose.21
4.2.7.7.2 Specification.21
4.2.7.7.3 Conformance tests.21
5 Testing for compliance with technical requirements.22
5.1 Environmental conditions for testing .22
5.2 Essential radio test suites.22
6 Test method.22
6.1 General.22
6.2 Off-axis spurious radiation.23
6.2.1 Test method.23
6.2.1.1 General.23
6.2.1.2 Multi-carrier operation.23
6.2.2 Measurements up to 1 000 MHz.24
6.2.2.1 Test site.24
6.2.2.2 Measuring receivers.24
6.2.2.3 Procedure.24
6.2.3 Measurements above 1 000 MHz .24
6.2.3.1 Identification of the significant frequencies of spurious radiation .25
6.2.3.1.1 Test site.25
6.2.3.1.2 Procedure.25
6.2.3.2 Measurement of radiated power levels of identified spurious radiation.25
6.2.3.2.1 Test site.25
6.2.3.2.2 Procedure.26
6.2.3.3 Measurement of conducted spurious radiation at the antenna flange.27
6.2.3.3.1 Test site.27
6.2.3.3.2 Procedure.27
6.3 On-axis spurious radiation.28
6.3.1 Test method.28
6.3.1.1 Test site.28
6.3.1.2 Method of measurement.28
6.3.1.2.1 General.28
6.3.1.2.2 Method of measurement at the antenna flange .28
6.3.1.2.3 Method of measurement for an EUT with antenna.29
6.4 Off-axis e.i.r.p. emission density within the band .30
6.4.1 Test method.30
6.4.1.1 Transmit output power density.30
6.4.1.1.1 General.30
6.4.1.1.2 Test site.30
6.4.1.1.3 Method of measurement.31
6.4.1.2 Antenna transmit gain.32
6.4.1.2.1 General.32
6.4.1.2.2 Test site.32
6.4.1.2.3 Method of measurement.32
6.4.1.3 Antenna transmit radiation patterns .33
6.4.1.3.1 General.33
6.4.1.3.2 Test site.33
6.4.1.3.3 Test arrangement.33
6.4.1.3.4 Co-polar radiation pattern - azimuth.33
6.4.1.3.5 Co-polar radiation pattern - elevation.34
6.4.1.3.6 Cross-polar radiation pattern - azimuth .35
6.4.1.3.7 Cross-polar radiation pattern - elevation .35
6.4.2 Computation of results.36
6.5 Carrier suppression.36
6.6 Antenna pointing for STs .36
ETSI

---------------------- Page: 6 ----------------------

SIST EN 301 459 V1.4.1:2007
 5 ETSI EN 301 459 V1.4.1 (2007-06)
6.7 ST Control and Monitoring Functions (CMF).37
6.7.1 Test arrangement.37
6.7.2 Processor monitoring - Test method .38
6.7.3 Transmit subsystem monitoring - Test method.38
6.7.4 Power-on/Reset - Test method.39
6.7.5 Control Channel (CC) reception - Test method .39
6.7.6 Network Control commands - Test method.40
6.7.7 Initial burst transmission - Test method.41
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT).43
Annex B (informative): Pointing stability methodology .45
Annex C (informative): The EN title in the official languages .46
Annex D (informative): Bibliography.48
History .49

ETSI

---------------------- Page: 7 ----------------------

SIST EN 301 459 V1.4.1:2007
 6 ETSI EN 301 459 V1.4.1 (2007-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Satellite Earth Stations and Systems (SES).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [2] of the European Parliament and
of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [2] are given in annex A.

National transposition dates
Date of adoption of this EN: 8 June 2007
Date of latest announcement of this EN (doa): 30 September 2007
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2008
Date of withdrawal of any conflicting National Standard (dow): 31 March 2009

ETSI

---------------------- Page: 8 ----------------------

SIST EN 301 459 V1.4.1:2007
 7 ETSI EN 301 459 V1.4.1 (2007-06)
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive. The modular
structure is shown in EG 201 399 (see bibliography).
Remarks on the present document
The present document applies to Satellite Interactive Terminals (SITs) and Satellite User Terminals (SUTs) either for
individual or collective use.
The present document deals with the specification defined to protect other users of the frequency spectrum, both
satellite and terrestrial, from harmful interference.
The determination of the parameters of the user earth stations using a given geostationary satellite for the protection of
the spectrum allocated to that satellite, is considered to be under the responsibility of the satellite operator or the
satellite network operators.
The requirements have been selected to ensure an adequate level of compatibility with other radio services. The levels,
however, do not cover extreme cases which may occur in any location but with a low probability of occurrence.
The present document may not cover those cases where a potential source of interference which is producing
individually repeated transient phenomena or a continuous phenomenon is present, e.g. a radar or broadcast site in the
near vicinity. In such a case it may be necessary to use special protection applied to the source of interference, or the
interfered part or both.
The present document does not contain any requirement, recommendation or information about the installation of SITs
and SUTs.
ETSI

---------------------- Page: 9 ----------------------

SIST EN 301 459 V1.4.1:2007
 8 ETSI EN 301 459 V1.4.1 (2007-06)
1 Scope
The present document applies to Satellite Interactive Terminals (SIT) and Satellite User Terminals (SUT) operating as
part of a bi-directional satellite network. Satellite Terminal (ST) is used in the present document as a generic name that
refers equally to a SIT and/or a SUT.
In such a network a Network Control Facility (NCF) is responsible for the monitoring and control of the transmit
functions of the STs. These STs have the following characteristics:
• in the case of SITs reception is in the Fixed Satellite Service (FSS) frequency ranges from 10,70 GHz to
11,70 GHz and from 12,50 GHz to 12,75 GHz, as well as the Broadcast Satellite Service (BSS) frequency
range from 11,70 GHz to 12,50 GHz;
• in the case of SUTs reception is in the Fixed Satellite Service (FSS) frequency ranges from 19,70 GHz to
20,20 GHz and from 17,70 GHz to 19,70 GHz, as well as the Broadcast Satellite Service (BSS) frequency
range from 21,40 GHz to 22,00 GHz;
• in all cases ST transmission is in the frequency band allocated to FSS on a primary basis from 29,5 GHz to
30,0 GHz;
• STs transmit towards geostationary satellites with spacing down to 2° away from any other geostationary
satellite operating in the same frequency band and covering the same area;
• linear or circular polarization is used for transmission or reception;
• the received signals may be analogue and/or digital;
• the transmitted signals are always of digital nature;
• the ST antenna diameter does not exceed 1,8 m, or equivalent effective area;
• the ST is designed for unattended operations.
The equipment considered in the present document comprises both the outdoor unit, usually composed of the antenna
subsystem and associated upconverter, power amplifier and Low Noise Block (LNB) downconverter, and the indoor
unit, usually composed of receive and transmit logic as well as the modulator, including cables between these two units.
The present document applies to the ST with its ancillary equipment and its various ports and when operated within the
boundary limits of all the operational environmental profile declared by the applic
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.