Small wastewater treatment systems for up to 50 PT - Part 7: Prefabricated tertiary treatment units

This European Standard specifies requirements, test methods, the marking and evaluation of conformity for a packaged and/or site assembled tertiary treatment unit for installation either separately or in a pre-existing unit. It applies for tertiary treatment units that are placed on the market as complete units used for the tertiary treatment of domestic wastewater by biological, physical, chemical, electrical processes and coming from: a) units in accordance with EN 12566-3 or EN 12566-6; b) installations designed and constructed in accordance with CEN/TR 12566-5. Equivalent secondary treated effluent may come from existing systems. Package and/or site assembled tertiary treatment units according to this standard consist of one or more watertight tanks without any direct infiltration into the ground, made of concrete, corrosion resistant or coated steel, un-plasticised poly-vinyl chloride (PVC-U), polyethylene (PE), glass reinforced thermosetting plastics (GRP) based on polyester resin (UP) (GRP-UP), polypropylene (PP) and polydicyclopentadiene (PDCPD).

Kleinkläranlagen für bis zu 50 EW - Teil 7: Vorgefertigte Anlagen für eine dritte Reinigungsstufe

Petites installations de traitement des eaux usées pour une population totale équivalente (PTE) jusqu’à 50 habitants - Partie 7 : Unités préfabriquées de traitement tertiaire

Male čistilne naprave do 50 PE - 7. del: Predizdelane čistilne enote za terciarno čiščenje

Ta evropski standard podaja zahteve, preskusne metode, označevanje in ocenjevanje skladnosti za predizdelane in/ali na mestu postavitve sestavljene terciarne čistilne enote za namestitev posebej ali v obstoječe enote. Uporablja se za terciarne čistilne enote, ki so na trgu na voljo kot celotne enote za terciarno čiščenje odpadne vode iz gospodinjstev z biološkimi, fizičnimi, kemičnimi in električnimi postopki ter izhajajo iz: a) enot, ki so v skladu s standardom EN 12566-3 ali EN 12566-6; b) naprav, ki so načrtovane in izdelane v skladu s standardom CEN/TR 12566-5. Iz obstoječih naprav lahko izhajajo enakovredne sekundarno prečiščene odplake. Embalaža in/ali na kraju samem sestavljene terciarne čistilne enote, ki so v skladu s tem standardom, so sestavljene iz enega ali več vodotesnih rezervoarjev brez infiltracije v zemljo in so izdelane iz betona, prevlečenega ali proti koroziji odpornega jekla, neplastificiranega polivinilklorida (PVC-U), polietilena (PE), s steklenimi vlakni ojačanih duromernih materialov (GRP) na osnovi nenasičene poliestrske smole (UP) (GRP-UP), polipropilena (PP) in polidiciklopentadiena (PDCPD).

General Information

Status
Published
Public Enquiry End Date
30-Mar-2016
Publication Date
09-Jan-2017
Current Stage
6100 - Translation of adopted SIST standards (Adopted Project)
Start Date
07-Nov-2017
Due Date
06-Nov-2018
Completion Date
11-Jun-2018

Relations

Buy Standard

Standard
EN 12566-7:2017
English language
47 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard – translation
EN 12566-7:2017
Slovenian language
46 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.þLãþHQMHKleinkläranlagen für bis zu 50 EW - Teil 7: Vorgefertigte Anlagen für eine dritte ReinigungsstufePetites installations de traitement des eaux usées pour une population totale équivalente (PTE) jusqu’à 50 habitants - Partie 7 : Unités préfabriquées de traitement tertiaireSmall wastewater treatment systems for up to 50 PT - Part 7: Prefabricated tertiary treatment units13.060.30Odpadna vodaSewage waterICS:Ta slovenski standard je istoveten z:EN 12566-7:2016SIST EN 12566-7:2017en,fr,de01-februar-2017SIST EN 12566-7:2017SLOVENSKI
STANDARDSIST EN 12566-7:20131DGRPHãþD



SIST EN 12566-7:2017



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12566-7
August
t r s x ICS
s uä r x rä u r Supersedes EN
s t w x xæ yã t r s uEnglish Version
Small wastewater treatment systems for up to
w r PT æ Part
yã Prefabricated tertiary treatment units Petites installations de traitement des eaux usées jusqu 5à
w r PTE æ Partie
yã Unités préfabriquées de traitement tertiaire
Kleinkläranlagen für bis zu
w r EW æ Teil
yã Im Werk vorgefertigte Einheiten für eine dritte ReinigungsstufeThis European Standard was approved by CEN on
t w June
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s t w x xæ yã t r s x ESIST EN 12566-7:2017



EN 12566-7:2016 (E) 2 Contents Page European foreword . 4 1 Scope . 6 2 Normative references . 6 3 Terms, definitions, symbols and abbreviated terms . 6 3.1 Terms and definitions . 6 3.2 Symbols and abbreviated terms . 8 4 Product characteristics . 8 4.1 Design . 8 4.1.1 General . 8 4.1.2 Overall dimensions . 8 4.1.3 Inlets, outlets, internal pipework and connections . 8 4.1.4 Access . 9 4.2 Load bearing capacity . 9 4.3 Tertiary treatment efficiency . 9 4.4 Watertightness . 10 4.5 Power consumption . 10 4.6 Durability . 10 4.6.1 General . 10 4.6.2 Concrete, steel, PVC-U, PE, GRP, PDCPD and flexible sheets . 10 4.7 Reaction to fire . 10 4.7.1 General . 10 4.7.2 Units classified as Class A1 without the need for testing . 11 4.7.3 Units classified according to the test results . 11 4.8 Dangerous substances . 11 5 Testing, assessment and sampling . 12 5.1 Load bearing capacity . 12 5.1.1 Generals . 12 5.1.2 Load bearing capacity determined by calculation . 12 5.1.3 Load bearing capacity determined by testing . 13 5.2 Tertiary treatment efficiency . 15 5.3 Watertightness . 15 5.4 Power consumption . 15 6 Assessment and verification of constancy of performance – AVCP. 15 6.1 General . 15 6.2 Type testing . 16 6.2.1 General . 16 6.2.2 Test samples, testing and compliance criteria . 16 6.2.3 Test reports . 18 6.2.4 Shared other party results . 18 6.2.5 Cascading determination of the product type results . 19 6.3 Factory production control . 20 6.3.1 General . 20 6.3.2 Requirements . 20 6.3.3 Product specific requirements . 23 6.3.4 Initial inspection of factory and of FPC . 23 6.3.5 Continuous surveillance of FPC . 24 6.3.6 Procedure for modifications . 24 SIST EN 12566-7:2017



EN 12566-7:2016 (E) 3 6.3.7 One-off products, pre-production products (e.g. prototypes) and products produced in very low quantity . 24 7 Nominal designation. 25 8 Marking, labelling and packaging . 25 8.1 Marking . 25 8.2 Technical information accompanying the unit . 26 8.3 Installation instructions . 27 8.4 Operation manual . 27 Annex A (normative)
Tertiary treatment efficiency test procedure . 29 A.1 Preliminary requirements . 29 A.1.1 General . 29 A.1.2 Installation and commissioning . 29 A.1.3 Operation procedures during testing. 29 A.1.4 Data to be monitored. 29 A.2 Test procedure . 30 A.2.1 Time for establishment . 30 A.2.2 Influent characteristics . 30 A.2.3 Daily flow pattern for testing . 30 A.2.4 Test procedure . 30 A.2.4.1 General . 30 A.2.4.2 Overload . 31 A.2.4.3 Power breakdown/Machine breakdown . 31 A.2.4.4 Power consumption . 31 A.2.5 Influent and effluent sampling. 32 A.3 Sample analysis . 32 A.4 Test report . 32 Annex B (normative)
Definition of processes . 33 Annex C (informative)
Analysis method . 34 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation . 35 ZA.1 Scope and relevant characteristics . 35 ZA.2 Procedure of attestation of conformity of prefabricated tertiary treatment unit . 36 ZA.2.1 System(s) of AVCP . 36 ZA.2.2 Declaration of performance (DoP) . 39 ZA.2.2.1 General . 39 ZA.2.2.2 Content . 40 ZA.2.2.3 Example of DoP . 41 ZA.3 CE marking and labelling . 43 Bibliography . 46 SIST EN 12566-7:2017



EN 12566-7:2016 (E) 4
European foreword This document (EN 12566-7:2016) has been prepared by Technical Committee CEN/TC 165 “Wastewater engineering”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2017, and conflicting national standards shall be withdrawn at the latest by May 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12566-7:2013. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. The differences between this version and EN 12566-7:2013 are mainly editorial changes according to the Construction Product Regulation (CPR) and declaration of power consumption and desludging during treatment efficiency test. The standard series EN 12566 “Small wastewater treatment systems for up to 50 PT” contains the following parts (see Figure 1): — Part 1: Prefabricated septic tanks; — Part 3: Packaged and/or site assembled domestic wastewater treatment plants; — Part 4: Septic tanks assembled in situ from prefabricated kits; — Part 6: Prefabricated treatment unit used for septic tank effluent; — Part 7: Prefabricated tertiary treatment unit (this document). For filtration systems, CEN/TC 165 decided to publish the following CEN Technical reports, which are considered as Code of practices and do not specify treatment requirements: — Part 2: Soil infiltration systems; — Part 5: Pre-treated Effluent Filtration systems. SIST EN 12566-7:2017



EN 12566-7:2016 (E) 5
Key A domestic wastewater 1 prefabricated septic tank B septic tank effluent 2 soil infiltration system C treated infiltrated effluent 3 packaged and/or site assembled domestic wastewater treatment plant D treated wastewater 4 septic tank assembled in situ from prefabricated kit E tertiary treated wastewater 5 pre-treated effluent filtration system
6 prefabricated treatment unit used for septic tank effluent
7 prefabricated tertiary treatment unit National regulations may specify different arrangements between the products described in the standard series EN 12566. Figure 1 — Scheme related to the arrangement of the parts of EN 12566 According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 12566-7:2017



EN 12566-7:2016 (E) 6 1 Scope This European Standard specifies requirements, test methods, the marking and evaluation of conformity for a packaged and/or site assembled tertiary treatment unit (see Figure 1). It applies for tertiary treatment units that are placed on the market as complete units used for the tertiary treatment of domestic wastewater by biological, physical, chemical, electrical processes and coming from: a) units in accordance with EN 12566-3 or EN 12566-6; b) installations designed and constructed in accordance with CEN/TR 12566-5. Equivalent secondary treated effluent may come from existing systems. Package and/or site assembled tertiary treatment units according to this standard consist of one or more watertight tanks without any direct infiltration into the ground, made of concrete, corrosion resistant or coated steel, un-plasticised poly-vinyl chloride (PVC-U), polyethylene (PE), glass reinforced thermosetting plastics (GRP) based on polyester resin (UP) (GRP-UP), polypropylene (PP), polydicyclopentadiene (PDCPD) and flexible sheets (HDPE, PP, PVE and EPDM). This standard applies to tertiary treatment units for use above ground (outside the building) or buried in the ground where no vehicle loads are applied to the unit. This standard does not apply to tertiary treatment systems forming part of units covered by EN 12566-3 and EN 12566-6. This standard does not cover the systems for microorganism reduction. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12566-3:2016, Small wastewater treatment systems for up to 50 PT — Part 3: Packaged and/or site assembled domestic wastewater treatment plants CEN/TR 12566-5, Small wastewater treatment systems up to 50 PT — Part 5: Pre-treated Effluent Filtration systems EN 12566-6:2016, Small wastewater treatment systems for up to 50 PT — Part 6: Prefabricated treatment units for septic tank effluent EN 13501-1, Fire classification of construction products and building elements — Part 1: Classification using data from reaction to fire tests EN 16323:2014, Glossary of wastewater engineering terms 3 Terms, definitions, symbols and abbreviated terms 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12566-3:2016,
EN 12566-6:2016, EN 16323:2014 and the following apply. SIST EN 12566-7:2017



EN 12566-7:2016 (E) 7 3.1.1 tertiary treatment additional treatment process which results in further purification than that obtained by applying primary and secondary treatment Note 1 to entry: It is recommended that the expression for the treatment, e.g. nitrogen removal, phosphorus removal, polishing effects, suspended solid removal, is used since in some case the tertiary treatment can also be integrated in the secondary treatment. 3.1.2 packaged unit prefabricated factory-built unit 3.1.3 site assembled unit unit composed of prefabricated components assembled on site coming from one manufacturer 3.1.4 biological processes processes in which the treatment is mainly carried out by micro-organism activity 3.1.5 physical processes processes in which the treatment is mainly carried out by using the physical properties of a media 3.1.6 chemical processes processes in which the treatment is mainly carried out by the addition of chemical agents 3.1.7 electrical processes processes in which the treatment is mainly carried out by the use of electricity 3.1.8 product family group of products in which, for the purpose of evaluation, the selected property(s) is/are similar for all products within the group Note 1 to entry: The definition of family takes into account at least similar shape, equipment, materials and conditions of end use and ensures the minimum hydraulic efficiency and minimum structural behaviour for all the products in the range. Note 2 to entry: The minimum level of performance (hydraulic efficiency and structural behaviour) are given by the test carried out on one model of the family. 3.1.9 tertiary treatment retrofit unit tertiary treatment unit installed within an existing package and/or site assembled domestic wastewater treatment plant in accordance with EN 12566-3, or a secondary treatment unit in accordance with EN 12566-6 or a pre-treated effluent filtration system in accordance with CEN/TR 12566-5 Note 1 to entry: Where such a retrofit unit affects the declared performance of EN 12566–3 or EN 12566–6 unit in which it is installed, then the overall unit should be tested for its conformity with the relevant standard. SIST EN 12566-7:2017



EN 12566-7:2016 (E) 8 3.1.10 nominal designation expressed as an integer giving the maximum number of population equivalent appropriate to the plant 3.2 Symbols and abbreviated terms The following symbols and abbreviations are used in this standard: BOD5 (or BOD7) Biochemical oxygen demand at 5 days (or 7 days) COD Chemical oxygen demand SS Suspended solids Total N Total nitrogen Total P Total phosphorus TOC Total organic carbon PP Polypropylene PDCPD Polydicyclopentadiene HDPE High Density Polyethylene PVC Polyvinyl Chloride EPDM Ethylene Propylene Diene Monomer PE Polyethylene 4 Product characteristics 4.1 Design 4.1.1 General Tertiary treatment units shall be designed to be structurally stable with the expected loads for the intended use. In addition, the units shall be durable, watertight and corrosion resistant. Where electrical, mechanical or hydraulic malfunction of the unit could lead to any failure, it shall be provided with an alarm to indicate such failure. The functionality of the alarm shall be verified as referenced in Table A.2. 4.1.2 Overall dimensions The overall dimensions of the prefabricated tertiary treatment unit (i.e. height, width, length, diameters, etc.) shall be measured and declared together with a tolerance. Assessment of overall dimensions shall be done by measurement with accuracy of ± 0,5 % of the dimension. 4.1.3 Inlets, outlets, internal pipework and connections The nominal diameters for inlet and outlet pipework of the prefabricated tertiary treatment unit shall be declared in the technical documentation. The hydraulic design of the unit, the internal pipework and the connections shall ensure that no accidental back-flows, blockage or surcharging occur during normal operation of the plant. Inlet and outlet pipes shall be compatible with standardised pipe systems. SIST EN 12566-7:2017



EN 12566-7:2016 (E) 9 Assessment of inlets, outlets, internal pipework and connections shall be done by measurement with accuracy of ± 0,5 % of the dimension. 4.1.4 Access The prefabricated tertiary treatment unit shall be designed to restrict unauthorised access (e.g. locking mechanism). The design of the unit shall provide access to allow routine maintenance sampling, removal of sludge (where applicable), cleaning and maintenance. An opening with a dimension (i.e. length for rectangular section or diameter for circular section) of a minimum 400 mm shall be required. For open unit, access is not required. For installation purposes of open units, there may be local regulations for maintenance access. NOTE 1 For installation purposes of open units, there may be local regulations for maintenance access. NOTE 2 The requirements to provide facility for the access of a person into the plant may depend on applicable regulations, valid in the member state for the intended end use conditions. For example, the minimum dimension of the opening for the access of a person in EN 476 is 600 mm. Extension shafts, where applicable, and access covers of the prefabricated tertiary treatment unit shall be designed to be fit for purpose. The access dimensions shall be declared. Assessment of access dimension shall be done by measurement with accuracy of 0,5 % of the dimension. The plant shall be designed to restrict unauthorized access by one of the following means: a) mass of the individual covers; b) securing feature; or c) locking accessory. Where a locking accessory or securing feature is used, it shall be designed so that the cover cannot be easily opened with objects readily accessible by children. 4.2 Load bearing capacity For units not including a tank, load bearing capacity assessment is not required. Test methods and values for mechanical characteristics of the materials of the tank, used for calculation of the load bearing capacity of the tank, shall be in accordance with EN 12566-3:2016, Annex D. The prefabricated tertiary treatment units shall resist the loads resulting from handling, installation and use including desludging and maintenance, for their design life. When tested according to 5.1, the load bearing capacity is declared as: — maximum allowed height of backfill (m); — possibility to install the unit in water table or not, expressed as WET or DRY, respectively. 4.3 Tertiary treatment efficiency For the purpose of determination of the tertiary treatment efficiency the tertiary treatment unit shall be determined by testing in accordance with Annex A. If there is an effect of the tertiary treatment process on BOD5 or BOD7, COD, SS inlet concentrations and nitrogen parameters and total phosphorus, then that effect shall be declared. SIST EN 12566-7:2017



EN 12566-7:2016 (E) 10 All parameters relevant for the treatment process of upstream units according to EN 12566-3 or EN 12566-6 shall be measured even if not declared by the manufacturer for CE-marking. The tertiary treatment efficiency shall be expressed in terms of tertiary treatment efficiency ratios with the indication of the organic load tested and the parameter to be reduced. In addition, the number of desludging procedures carried out during the test according to Annex A, shall be declared. Each tertiary treatment efficiency ratio shall be calculated according to 5.2. 4.4 Watertightness The tertiary treatment unit shall be watertight. It shall be tested according to 5.3 For units not including a tank, watertightness test is not required. 4.5 Power consumption The power consumption of the unit shall be declared according to 5.4. The declared power consumption value shall be higher or equal to the measured value during the test in A.2.4.4. 4.6 Durability 4.6.1 General The prefabricated tertiary treatment units, including all their internal components, shall be manufactured from materials that make them, from the durability aspects, suitable for use in a domestic wastewater environment. Materials of the other components of the unit (i.e. filter material, pump, etc.) shall be in accordance with the specifications given by the manufacturer to the material/component supplier. 4.6.2 Concrete, steel, PVC-U, PE, GRP, PDCPD and flexible sheets For concrete,
...

ba

SLOVENSKI SIST EN 12566-7


STANDARD februar 2017













Male čistilne naprave do 50 PE – 7. del: Predizdelane čistilne enote za
terciarno čiščenje

Small wastewater treatment systems for up to 50 PT – Part 7: Prefabricated
tertiary treatment units

Petites installations de traitement des eaux usées pour une population totale
équivalente (PTE) jusqu’à 50 habitants – Partie 7: Unités préfabriquées de
traitement tertiaire

Kleinkläranlagen für bis zu 50 EW – Teil 7: Vorgefertigte Anlagen für eine dritte
Reinigungsstufe


















Referenčna oznaka
ICS 13.060.30 SIST EN 12566-7:2017 (sl)

Nadaljevanje na straneh II do III in od 1 do 44

© 2018-07. Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 12566-7 : 2017

NACIONALNI UVOD

Standard SIST EN 12566-7 (sl), Male čistilne naprave do 50 PE – 7. del: Predizdelane čistilne enote za
terciarno čiščenje, 2017, ima status slovenskega standarda in je enakovreden evropskemu standardu
EN 12566-7 (en, de, fr), Small wastewater treatment systems for up to 50 PT – Part 7: Prefabricated
tertiary treatment units, 2016.

Ta standard nadomešča SIST EN 12566-7:2013.

NACIONALNI PREDGOVOR

Evropski standard EN 12566-7:2016 je pripravil tehnični odbor Evropskega komiteja za standardizacijo
CEN/TC 165 Projektiranje kanalizacijskih sistemov. Slovenski standard SIST EN 12566-7:2017 je
prevod evropskega standarda EN 12566-7:2016. V primeru spora glede besedila slovenskega prevoda
v tem standardu je odločilen izvirni evropski standard v enem izmed treh uradnih jezikov CEN.
Slovensko izdajo standarda je potrdil Strokovni svet SIST za splošno področje standardizacije.

Odločitev za izdajo tega standarda je dne 10. januarja 2017 sprejel Strokovni svet SIST za splošno
področje standardizacije.

ZVEZA S STANDARDI

S privzemom tega evropskega standarda veljajo za omejeni namen referenčnih standardov vsi
standardi, navedeni v izvirniku, razen tistih, ki so že sprejeti v nacionalno standardizacijo:

SIST EN 12566-3:2017 Male čistilne naprave do 50 PE – 3. del: Predizdelane in/ali na mestu
postavitve sestavljene čistilne naprave za gospodinjsko odpadno vodo

SIST-TP CEN/TR 12566-5 Male čistilne naprave do 50 PE – 5. del: Filtrirne naprave za predčiščeno
gospodinjsko odpadno vodo

SIST EN 12566-6:2017 Male čistilne naprave do 50 PE – 6. del: Predizdelane enote za čiščenje
odpadne vode iz greznic

SIST EN 13501-1 Požarna klasifikacija gradbenih proizvodov in elementov stavb – 1. del:
Klasifikacija po podatkih iz preskusov odziva na ogenj

SIST EN 16323:2014 Slovar s področja odpadnih voda

OSNOVA ZA IZDAJO STANDARDA

— privzem standarda EN 12566-7:2016

PREDHODNA IZDAJA

‒ SIST EN 12566-7:2013, Male čistilne naprave do 50 PE – 7. del: Predizdelane terciarne čistilne
enote

OPOMBE

— Povsod, kjer se v besedilu standarda uporablja izraz "evropski standard", v SIST EN 12566-7:2017
to pomeni "slovenski standard".

— Uvod in nacionalni predgovor nista sestavni del standarda.


II

---------------------- Page: 2 ----------------------

SIST EN 13108-7 : 2017

‒ Ta nacionalni dokument je istoveten EN 12566-7:2016 in je objavljen z dovoljenjem

CEN-CENELEC
Upravni center
Avenue Marnix 17
B-1000 Bruselj

This national document is identical with EN 12566-7:2016 and is published with the permission of
CEN-CENELEC
Management Centre
Avenue Marnix 17
B-1000 Brussels


III

---------------------- Page: 3 ----------------------

SIST EN 12566-7 : 2017






















(prazna stran)

IV

---------------------- Page: 4 ----------------------

EVROPSKI STANDARD            EN 12566-7
EUROPEAN STANDARD

NORME EUROPÉENNE
avgust 2016
EUROPÄISCHE NORM

ICS 13.060.30



Slovenska izdaja

Male čistilne naprave do 50 PE –
7. del: Predizdelane čistilne enote za terciarno čiščenje


Small wastewater treatment Petites installations de traitement Kleinkläranlagen für bis zu 50
systems for up to 50 PT – Part 7: des eaux usées pour une EW – Teil 7: Vorgefertigte
Prefabricated tertiary treatment population totale équivalente Anlagen für eine dritte
units (PTE) jusqu’à 50 habitants – Reinigungsstufe
Partie 7: Unités préfabriquées de
traitement tertiaire





Ta evropski standard je CEN sprejel dne 25. junija 2016.

Člani CEN morajo izpolnjevati notranje predpise CEN/CENELEC, ki določajo pogoje, pod katerimi dobi
ta standard status nacionalnega standarda brez kakršnihkoli sprememb. Seznami najnovejših izdaj teh
nacionalnih standardov in njihovi bibliografski podatki so na voljo na zahtevo pri centralnem sekretariatu
CEN-CENELEC ali članih CEN.

Ta evropski standard obstaja v treh uradnih izdajah (angleški, francoski in nemški). Izdaje v drugih
jezikih, ki jih člani CEN na lastno odgovornost prevedejo in izdajo ter prijavijo pri centralnem sekretariatu
CEN-CENELEC, veljajo kot uradne izdaje.

Člani CEN so nacionalni organi za standarde Avstrije, Belgije, Bolgarije, Cipra, Češke republike,
Danske, Estonije, Finske, Francije, Grčije, Hrvaške, Irske, Islandije, Italije, Latvije, Litve, Luksemburga,
Madžarske, Malte, Nekdanje jugoslovanske republike Makedonije, Nemčije, Nizozemske, Norveške,
Poljske, Portugalske, Romunije, Slovaške, Slovenije, Španije, Švedske, Švice, Turčije in Združenega
kraljestva.














CEN
Evropski komite za standardizacijo
European Committee for Standardization
Comité Européen de Normalisation
Europäisches Komitee für Normung

Upravni center CEN-CENELEC: Avenue Marnix 17, B-1000 Bruselj

© 2016 CEN Lastnice vseh oblik avtorskih pravic so vse države članice CEN. Ref. oznaka EN 12566-7:2016 E

---------------------- Page: 5 ----------------------

SIST EN 12566-7 : 2017

VSEBINA Stran

Evropski predgovor . 5
1 Področje uporabe . 7
2  Zveze s standardi . 7
3  Izrazi, definicije, simboli in kratice . 7
3.1 Izrazi in definicije . 7
3.2 Simboli in kratice . 9
4  Lastnosti proizvoda . 9
4.1 Projektiranje . 9
4.1.1 Splošno . 9
4.1.2 Skupne dimenzije . 9
4.1.3 Vtočne in iztočne odprtine, notranji cevovod ter priključki . 9
4.1.4 Dostop . 10
4.2 Obremenitvena zmogljivost . 10
4.3 Učinkovitost terciarnega čiščenja . 10
4.4 Vodotesnost . 11
4.5 Poraba energije . 11
4.6 Trajnost . 11
4.6.1 Splošno . 11
4.6.2 Beton, jeklo, PVC-U, PE, GRP, PDCPD in hidroizolacijski trakovi . 11
4.7 Odziv na ogenj . 11
4.7.1 Splošno . 11
4.7.2 Enote, klasificirane kot razred A1 brez potrebe po preskušanju . 12
4.7.3 Enote, klasificirane v skladu z rezultati preskušanja . 12
4.8 Nevarne snovi . 12
5 Preskušanje, ocenjevanje in vzorčenje . 13
5.1 Obremenitvena zmogljivost . 13
5.1.1 Splošno . 13
5.1.2 Obremenitvena zmogljivost, določena z izračunom . 13
5.1.3 Obremenitvena zmogljivost, določena s preskušanjem . 14
5.2 Učinkovitost terciarnega čiščenja . 16
5.3 Vodotesnost . 16
5.4 Poraba energije . 16
6 Ocenjevanje in preverjanje nespremenljivosti lastnosti – AVCP . 16
6.1 Splošno . 16
6.2 Tipsko preskušanje . 16
6.2.1 Splošno . 16
6.2.2 Preskusni vzorci, preskušanje in merila skladnosti . 17
6.2.3 Poročila o preskusih . 19
6.2.4 Rezultati, pridobljeni od tretjih oseb . 19
2

---------------------- Page: 6 ----------------------

SIST EN 12566-7 : 2017

6.2.5 Rezultati kaskadne določitve tipa proizvoda . 20
6.3 Kontrola proizvodnje v obratu . 21
6.3.1 Splošno . 21
6.3.2 Zahteve . 21
6.3.3 Posebne zahteve za proizvod . 24
6.3.4 Začetni pregled obrata in kontrole proizvodnje v obratu . 24
6.3.5 Redni nadzor nad kontrolo proizvodnje v obratu . 25
6.3.6 Postopek za spremembe . 25
6.3.7 Enkratni proizvodi, predproizvodni proizvodi (na primer prototipi) in proizvodi,
proizvedeni v zelo majhnih količinah  . 25
7 Nazivna oznaka . 26
8 Označevanje, etiketiranje in pakiranje . 26
8.1 Označevanje . 26
8.2 Tehnične informacije, ki so priložene enoti . 27
8.3 Navodila za vgradnjo . 27
8.4 Priročnik o obratovanju . 28
Dodatek A (normativni): Postopek preskusa učinkovitosti terciarnega čiščenja . 29
A.1 Predhodne zahteve . 29
A.1.1 Splošno . 29
A.1.2 Vgradnja in usposobitev za zagon . 29
A.1.3 Postopki upravljanja med preskušanjem . 29
A.1.4 Podatki za nadzor . 29
A.2 Preskusni postopek . 30
A.2.1 Čas vzpostavitve . 30
A.2.2 Lastnosti vtoka . 30
A.2.3 Vzorec dnevnega pretoka za preskušanje . 30
A.2.4 Preskusni postopek . 30
A.2.4.1 Splošno . 30
A.2.4.2 Preobremenitev . 31
A.2.4.3 Izpad napajanja/zaustavitev stroja . 31
A.2.4.4 Poraba energije . 31
A.2.5 Vzorci na vtoku in iztoku . 32
A.3 Analiza vzorcev . 32
A.4 Poročilo o preskusu . 32
Dodatek B (normativni): Definicije procesov . 33
Dodatek C (informativni): Metoda analiziranja . 34
Dodatek ZA (informativni): Točke tega evropskega standarda, ki se nanašajo na določila
Uredbe EU o gradbenih proizvodih . 35
ZA.1 Področje uporabe in ustrezne lastnosti . 35
ZA.2 Postopek potrjevanja skladnosti predizdelane čistilne enote za terciarno čiščenje . 36
ZA.2.1 Sistem(-i) ocenjevanja in preverjanja nespremenljivosti lastnosti . 36
3

---------------------- Page: 7 ----------------------

SIST EN 12566-7 : 2017

ZA.2.2 Izjava o lastnostih (DoP) . 38
ZA.2.2.1 Splošno . 38
ZA.2.2.2 Vsebina . 38
ZA.2.2.3 Primer izjave o lastnostih . 40
ZA.3 CE-označevanje in etiketiranje . 42
Literatura . 44

4

---------------------- Page: 8 ----------------------

SIST EN 12566-7 : 2017

Evropski predgovor

Ta dokument (EN 12566-7:2016) je pripravil tehnični odbor CEN/TC 165 "Projektiranje kanalizacijskih
sistemov", katerega sekretariat vodi DIN.

Ta evropski standard mora dobiti status nacionalnega standarda z objavo istovetnega besedila ali z
razglasitvijo najpozneje do februarja 2017, nasprotujoče nacionalne standarde pa je treba razveljaviti
najpozneje do maja 2018.

Opozoriti je treba na možnost, da so lahko nekateri elementi tega dokumenta predmet patentnih pravic.
CEN [in/ali CENELEC] ne prevzema odgovornosti za ugotavljanje posameznih ali vseh takih patentnih
pravic.

Ta dokument nadomešča EN 12566-7:2013.

Ta dokument je bil pripravljen na podlagi mandata, ki sta ga Evropska komisija in Evropsko združenje
za prosto trgovino podelila CEN, in podpira bistvene zahteve direktive (direktiv) EU.

Za povezavo z direktivo(-ami) EU glej informativni dodatek ZA, ki je sestavni del tega dokumenta.

Razlike med to izdajo in EN 12566-7:2013 so predvsem uredniške spremembe v skladu z Uredbo o
gradbenih proizvodih (CPR) in izjavo o porabi energije ter odvzemanju blata med preskušanjem
učinkovitosti čiščenja.

Skupina standardov EN 12566, Male čistilne naprave do 50 PE, vključuje naslednje dele (glej sliko 1):

‒ 1. del: Predizdelane greznice

‒ 3. del: Predizdelane in/ali na mestu postavitve sestavljene čistilne naprave za gospodinjsko
odpadno vodo

‒ 4. del: Montažne greznice, sestavljene na mestu vgradnje iz predizdelanih kompletov

‒ 6. del: Predizdelane enote za čiščenje odpadne vode iz greznic

‒ 7. del: Predizdelane čistilne enote za terciarno čiščenje

Za sisteme za filtriranje je CEN/TC 165 objavil naslednja tehnična poročila CEN, ki se upoštevajo kot
pravila ravnanja in ne določajo zahtev za čiščenje:

‒ 2. del: Sistemi za infiltracijo v tla

‒ 5. del: Filtrirne naprave za predčiščeno gospodinjsko odpadno vodo


5

---------------------- Page: 9 ----------------------

SIST EN 12566-7 : 2017


Legenda:

A gospodinjska odpadna voda 1 predizdelana greznica
B odpadna voda iz greznice 2 sistem za infiltracijo v tla
C čiščena infiltrirana odpadna voda 3 predizdelana in/ali na mestu vgradnje sestavljena čistilna naprava za
gospodinjsko odpadno vodo
D čiščena odpadna voda 4 montažna greznica, sestavljena na mestu vgradnje
E terciarno čiščena odpadna voda 5 filtrirni sistem za predčiščeno odpadno vodo
 6 predizdelana čistilna enota za odpadno vodo iz greznic
 7 predizdelana čistilna enota za terciarno čiščenje

Nacionalni predpisi lahko določajo drugačne razporeditve med proizvodi, opisanimi v standardih skupine
EN 12566.

Slika 1: Shema ureditve delov standarda EN 12566

Skladno z notranjimi predpisi CEN/CENELEC morajo ta evropski standard prevzeti nacionalne
organizacije za standarde naslednjih držav: Avstrije, Belgije, Bolgarije, Cipra, Češke republike, Danske,
Estonije, Finske, Francije, Grčije, Hrvaške, Irske, Islandije, Italije, Latvije, Litve, Luksemburga,
Madžarske, Malte, Nekdanje jugoslovanske republike Makedonije, Nemčije, Nizozemske, Norveške,
Poljske, Portugalske, Romunije, Slovaške, Slovenije, Španije, Švedske, Švice, Turčije in Združenega
kraljestva.





6

---------------------- Page: 10 ----------------------

SIST EN 12566-7 : 2017

1 Področje uporabe

Ta evropski standard določa zahteve, preskusne metode, označevanje in vrednotenje skladnosti
predizdelanih in/ali na mestu vgradnje sestavljenih čistilnih enot za terciarno čiščenje (glej sliko 1).

Uporablja se za čistilne enote za terciarno čiščenje, ki so dane na trg kot kompletne enote za terciarno
čiščenje gospodinjske odpadne vode z biološkimi, fizikalnimi, kemijskimi in električnimi postopki ter
izhajajo iz:

a) enot v skladu z EN 12566-3 ali EN 12566-6,

b) naprav, projektiranih in izdelanih v skladu s CEN/TR 12566-5.

Iz obstoječih sistemov lahko izhajajo enakovredne sekundarno čiščene odpadne vode.

Predizdelane in/ali na mestu vgradnje sestavljene čistilne enote za terciarno čiščenje, ki so v skladu s
tem standardom, so sestavljene iz enega ali več vodotesnih rezervoarjev brez neposredne infiltracije v
tla in so izdelane iz betona, prevlečenega ali proti koroziji odpornega jekla, neplastificiranega
polivinilklorida (PVC-U), polietilena (PE), s steklenimi vlakni ojačenih duromernih materialov (GRP) na
osnovi nenasičene poliestrske smole (UP) (GRP-UP), polipropilena (PP), polidiciklopentadiena
(PDCPD) ali hidroizolacijskih trakov (PEHD, PP, PVE in EPDM).

Ta standard se uporablja za čistilne enote za terciarno čiščenje, ki se uporabljajo nad površino (zunaj
zgradb) ali so zakopane pod površino, kjer niso izpostavljene obremenitvam vozil.

Ta standard se ne uporablja za sestavne dele čistilnih naprav za terciarno čiščenje, ki so obravnavani
v EN 12566-3 in EN 12566-6.

Ta standard ne obravnava sistemov za zmanjšanje količine prisotnih mikroorganizmov.

2 Zveze s standardi

Za uporabo tega standarda so, delno ali v celoti, nujno potrebni spodaj navedeni referenčni dokumenti.
Pri datiranih sklicevanjih se uporablja le navedena izdaja. Pri nedatiranih sklicevanjih se uporablja
zadnja izdaja publikacije (vključno z dopolnili).
EN 12566-3:2016 Male čistilne naprave do 50 PE – 3. del: Predizdelane in/ali na mestu
postavitve sestavljene čistilne naprave za gospodinjsko odpadno vodo

EN 12566-5 Male čistilne naprave do 50 PE – 5. del: Filtrirne naprave za predčiščeno
gospodinjsko odpadno vodo

EN 12566-6:2016 Male čistilne naprave do 50 PE – 6. del: Predizdelane enote za čiščenje
odpadne vode iz greznic

EN 13501-1 Požarna klasifikacija gradbenih proizvodov in elementov stavb – 1. del:
Klasifikacija po podatkih iz preskusov odziva na ogenj

EN 16323:2014 Glosar izrazov na področju projektiranja kanalizacijskih sistemov

3 Izrazi, definicije, simboli in kratice

3.1 Izrazi in definicije

V tem dokumentu se uporabljajo izrazi in definicije, navedeni v EN 12566-3:2016, EN 12566-6:2016 in
EN 16323:2014, ter naslednji izrazi in definicije:

3.1.1
terciarno čiščenje
dodaten postopek čiščenja za dodatno čiščenje primarno in sekundarno čiščene odpadne vode

7

---------------------- Page: 11 ----------------------

SIST EN 12566-7 : 2017

Opomba 1: Priporoča se uporaba izraza za čiščenje (npr. odstranjevanje dušika, odstranjevanje fosforja, učinki
poliranja, odstranjevanje neraztopljenih trdnih snovi), saj je v nekaterih primerih lahko postopek terciarnega
čiščenja vključen v postopek sekundarnega čiščenja.

3.1.2
predizdelana enota
tovarniško predizdelana enota

3.1.3
na mestu vgradnje sestavljena enota
enota, sestavljena na mestu vgradnje iz predizdelanih sestavnih delov istega proizvajalca

3.1.4
biološki procesi
procesi, v katerih se čiščenje izvaja v glavnem z dejavnostjo mikroorganizmov

3.1.5
fizikalni procesi
procesi, v katerih se čiščenje izvaja v glavnem z uporabo fizikalnih lastnosti medija

3.1.6
kemijski procesi
procesi, v katerih se čiščenje izvaja v glavnem z dodajanjem kemičnih sredstev

3.1.7
električni procesi
procesi, v katerih se čiščenje izvaja v glavnem z uporabo elektrike

3.1.8
družina proizvodov
skupina proizvodov, v kateri je (so) (za potrebe vrednotenja) izbrana(-e) lastnost(-i) podobna(-e) za vse
proizvode v skupini

OPOMBA 1: Definicija družine upošteva najmanj podobno obliko, opremo, materiale in pogoje končne uporabe ter
zagotavlja najmanjšo hidravlično učinkovitost in minimalno obnašanje konstrukcije za vse proizvode v
naboru.
OPOMBA 2: Najnižja raven zmogljivosti (hidravlična učinkovitost in obnašanje konstrukcije) se določi na podlagi
preskusa enega od modelov v družini.

3.1.9
čistilna enota za terciarno čiščenje za rekonstrukcijo
čistilna enota za terciarno čiščenje, vgrajena v obstoječo predizdelano in/ali na mestu vgradnje
sestavljeno čistilno napravo za gospodinjsko odpadno vodo v skladu z EN 12566-3, ali čistilna enota za
sekundarno čiščenje v skladu z EN 12566-6 ali filtrirna naprava za predčiščeno gospodinjsko odpadno
vodo v skladu s CEN/TR 12566-5

OPOMBA 1: Če enota za rekonstrukcijo vpliva na navedene lastnosti enote v skladu s standardom EN 12566-3 ali EN
12566-6, v katero je vgrajena, je treba preskusiti celotno enoto in preveriti njeno skladnost z ustreznim
standardom.

3.1.10
nazivna oznaka
izražena kot celo število, ki podaja največje število populacijskih ekvivalentov, ki ustreza napravi


8

---------------------- Page: 12 ----------------------

SIST EN 12566-7 : 2017

3.2 Simboli in kratice

V tem standardu se uporabljajo naslednji simboli in kratice:

BPK (ali BPK ) biokemijska potreba po kisiku po 5 ali 7 dneh
5 7

KPK kemijska potreba po kisiku

NS neraztopljene snovi

celotni N celotni dušik

celotni P celotni fosfor

TOC celotni organski ogljik

PP polipropilen

PDCPD polidiciklopentadien

HDPE polietilen z visoko gostoto

PVC polivinilklorid

EPDM etilen-propilen-dien monomer

PE polietilen

4 Lastnosti proizvoda

4.1 Projektiranje

4.1.1 Splošno

Čistilne enote za terciarno čiščenje morajo imeti stabilno konstrukcijo in prenesti pričakovane
obremenitve v okviru predvidene uporabe. Poleg tega morajo biti enote trajne, vodotesne in odporne
proti koroziji.

Kadar lahko električne, mehanske ali hidravlične pomanjkljivosti enote povzročijo morebitno odpoved,
mora biti enota opremljena z alarmom, ki opozarja na tako odpoved. Delovanje alarma mora biti
preverjeno, kot je navedeno v preglednici A.2.

4.1.2 Skupne dimenzije

Skupne dimenzije predizdelane čistilne enote za terciarno čiščenje (npr. višina, širina, dolžina, premeri
itd.) morajo biti izmerjene in navedene skupaj s tolerancami.

Skupne dimenzije morajo biti ocenjene z meritvami s točnostjo ±0,5 % pri posamezni dimenziji.
4.1.3 Vtočne in iztočne odprtine, notranji cevovod ter priključki

V tehnični dokumentaciji je treba navesti nazivne premere vtočnih in iztočnih cevi predizdelane čistilne
enote za terciarno čiščenje. Hidravlična zasnova enote, notranji cevovod in priključki morajo
preprečevati kakršnekoli povratne tokove, zamašitve ali preobremenitve pri običajnem obratovanju
enote.

Vtočne in iztočne cevi morajo biti združljive s standardiziranimi cevnimi sistemi.

Vtočne in iztočne cevi, notranji cevovod in priključki morajo biti ocenjeni z meritvami s točnostjo ±0,5 %
pri posamezni dimenziji.

9

---------------------- Page: 13 ----------------------

SIST EN 12566-7 : 2017

4.1.4 Dostop

Predizdelana čistilna enota za terciarno čiščenje mora biti zasnovana tako, da onemogoča
nepooblaščen dostop (npr. z zaklepnim mehanizmom).

Zasnova enote mora omogočati dostop za potrebe rednega vzdrževalnega vzorčenja, odvzemanja blata
(kjer je to primerno) ter čiščenja in vzdrževanja. Na voljo mora biti odprtina z dimenzijo (tj. širina pri
pravokotni površini ali premer pri krožni površini) vsaj 400 mm. Odprtina za dostop pri odprti enoti ni
potrebna.

Za vgradnjo odprtih enot lahko veljajo lokalni predpisi za dostop za vzdrževanje.

OPOMBA 1: Za vgradnjo odprtih enot lahko veljajo lokalni predpisi za dostop za vzdrževanje.

OPOMBA 2: Zahteve
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.