This document specifies methods for the hydrostatic testing of rubber and plastics hoses and hose assemblies, including methods for the determination of dimensional stability.

    • sale 15% off
    • Standard
      9 pages
      English language
    • sale 15% off
    • Standard
      10 pages
      French language
    • sale 15% off
    • Draft
      9 pages
      English language
    • sale 15% off
    • Draft
      9 pages
      French language

This document specifies requirements for two types of reinforced hoses and hose assemblies of nominal size from 3,2 to 25, dependent on relation of minimum burst pressure to maximum working pressure. Each type is divided into classes dependent on maximum working pressure. They are suitable for use with: —   oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C; —   water-based fluids HFC, HFAE, HFAS and HFB as de...view more

    • sale 15% off
    • Standard
      13 pages
      English language
    • sale 15% off
    • Draft
      13 pages
      English language

This document specifies three methods for determining the resistance to vacuum of hoses and hose assemblies manufactured from plastic or rubber. Applicable dimensions of hoses for each method are as follows: —   method A for hoses of nominal size up to and including 80; —   method B for hoses of nominal size greater than 80; —   method C for hoses of all dimensions. If not otherwise specified in the product standard, method C can be used as an alternative to methods A and B....view more

    • sale 15% off
    • Standard
      5 pages
      English language
    • sale 15% off
    • Standard
      5 pages
      French language
    • sale 15% off
    • Draft
      5 pages
      English language
    • sale 15% off
    • Draft
      5 pages
      French language

This document establishes the requirements and test methods for rubber and plastics suction hoses for fire-fighting purposes. These hoses can also be used manually to supply unpressurized water to the pump or for water discharge. NOTE      All pressures are expressed in megapascals and in bar (1 MPa = 10 bar). Additional requirements are specified for hose assemblies, that is, hoses with couplings already fitted, where this is carried out by the hose manufacturer (see Clause 8). TypeÂ...view more

    • sale 15% off
    • Standard
      18 pages
      English language
    • sale 15% off
    • Standard
      20 pages
      French language
    • sale 15% off
    • Draft
      18 pages
      English language
    • sale 15% off
    • Draft
      20 pages
      French language

This document specifies requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas and designed for use at working pressures ranging from vacuum to a maximum of 2,5 MPa (25 bar) within the temperature range −30 °C to +70 °C or, for low-temperature hoses (designated -LT), within the temperature range −50 °C to +70 °C.

    • sale 15% off
    • Standard
      12 pages
      English language
    • sale 15% off
    • Draft
      12 pages
      English language

This document specifies the requirements for rubber hoses and hose assemblies for wet and dry sand and grit blasting, suitable for use up to a maximum working pressure of 0,63 MPa (6,3 bar) and over an operating temperature range of −25 °C to +70 °C.

    • sale 15% off
    • Standard
      7 pages
      English language
    • sale 15% off
    • Standard
      8 pages
      French language
    • sale 15% off
    • Draft
      7 pages
      English language
    • sale 15% off
    • Draft
      8 pages
      French language

This document specifies the requirements for rubber or thermoplastic hoses and hose assemblies used for circulating liquid and gaseous R1234yf (tetrafluoropropene) in the air-conditioning systems of automobiles. The hoses and hose assemblies are designed in such a way as to restrict losses of refrigerant and contamination of the system. The operational temperature range is −40 °C to +125 °C. Due to the critical relationship between the hose and coupling for this application, a requirement that t...view more

    • sale 15% off
    • Standard
      28 pages
      English language

This document specifies requirements for three types of textile-reinforced thermoplastics hoses and hose assemblies of nominal size from 3,2 to 25. Each type is divided into two classes dependent on electrical conductivity requirements. They are suitable for use with: — oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743‑4 at temperatures ranging from −40 °C to +93 °C; — water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743‑4 at temperatures ranging from 0 °C to +...view more

    • sale 15% off
    • Standard
      13 pages
      English language
    • sale 15% off
    • Standard
      13 pages
      English language
    • sale 15% off
    • Standard
      13 pages
      French language
    • sale 15% off
    • Standard
      13 pages
      French language
    • sale 15% off
    • Standard
      13 pages
      French language
    • sale 15% off
    • Draft
      13 pages
      English language

This document specifies electrical test methods for rubber and plastics hoses, tubing and hose assemblies to determine the resistance of conductive, antistatic and non-conductive hoses and the electrical continuity or discontinuity between metal end fittings. All the test methods described for rubber hoses in this document can also be applied to plastics hoses.

    • sale 15% off
    • Standard
      16 pages
      English language
    • sale 15% off
    • Standard
      16 pages
      French language
    • sale 15% off
    • Draft
      16 pages
      English language

This document specifies requirements for five types of textile-reinforced hydraulic hoses and hose assemblies of nominal size from 5 to 100. They are suitable for use with: — oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743‑4 at temperatures ranging from −40 °C to +100 °C; — water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743‑4 at temperatures ranging from −40 °C to +70 °C; — water at temperatures ranging from 0 °C to +70 °C. This document does not include re...view more

    • sale 15% off
    • Standard
      13 pages
      English language
    • sale 15% off
    • Standard
      13 pages
      English language

This document specifies requirements for wire-reinforced hoses and hose assemblies for underground coal mining applications of nominal sizes 6,3 to 51 for use with: — oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +120 °C; — water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from −40 °C to +70 °C; — water at temperatures ranging from 0 °C to +70 °C. There is a possibility that operation at ...view more

    • sale 15% off
    • Standard
      4 pages
      English language
    • sale 15% off
    • Standard
      4 pages
      English language

This document specifies requirements for six types of wire-braid-reinforced hoses and hose assemblies of nominal size from 5 to 51. This document also specifies the hose of nominal size 63 for types 2SN and R2AT, and the hose of nominal size 76 for type 2SN. They are suitable for use with: — oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743‑4 at temperatures ranging from −40 °C to +100 °C; — water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743‑4 at temperatures...view more

    • sale 15% off
    • Standard
      13 pages
      English language
    • sale 15% off
    • Standard
      13 pages
      English language

This document specifies requirements for five types of spiral-wire-reinforced hydraulic hoses and hose assemblies of nominal size from 6,3 to 51. They are suitable for use with: — oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C for types 4SP and 4SH hoses and from −40 °C to +120 °C for types R12, R13 and R15 hoses; — water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from −40 °C to +...view more

    • sale 10% off
    • Standard
      17 pages
      English language
    • e-Library read for
      1 day
    • sale 15% off
    • Standard
      13 pages
      English language

This document specifies the requirements for rubber hoses and hose assemblies, up to a maximum hose size of 19, for use in motor vehicles with liquefied petroleum gas (LPG) installations. The hoses are designed for use up to a maximum working pressure of 3,0 MPa (30 bar) and at working temperatures from −40 °C up to and including +80 °C.

    • sale 15% off
    • Standard
      9 pages
      English language

This document specifies the requirements for three types of general-purpose textile-reinforced rubber water hose with an operating temperature range of −25 °C to +70 °C and a maximum working pressure of up to 2,5 MPa (25 bar). These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine inlets, as firefighting hoses, for special agricultural machines or as collapsible water hoses. These hoses can be used with additives which lower the freezing point of ...view more

    • sale 15% off
    • Standard
      4 pages
      English language
    • sale 15% off
    • Standard
      4 pages
      French language

This document specifies the requirements for rubber tubing and hoses used in diesel fuel circuits for internal combustion engines. The diesel fuels covered include "bio-diesels" which consist of the methyl ester of rape seed oil at levels up to 20 % by volume in conventional diesel fuels. This document can also be applied as a classification system to enable original equipment manufacturers (OEMs) to detail a "line call-out" of tests for specific applications where these are not covered by the m...view more

    • sale 15% off
    • Standard
      17 pages
      English language
    • sale 15% off
    • Standard
      1 page
      English language
    • sale 15% off
    • Standard
      1 page
      French language

This document specifies requirements for five types of hose and hose assembly used in automobile power-steering systems, the five types differing in their pressure ratings and volumetric expansion. They are for use with fluids in the temperature range −40 °C to +135 °C. This document is based on performance tests. In order to take account of technological developments, no requirements are included for specific materials, detailed construction or manufacturing methods.

    • sale 15% off
    • Standard
      10 pages
      English language

This document describes hose impulse testing, with flexing, of rubber or plastics hydraulic hose assemblies at both high and low impulse pressures. The high-pressure testing is carried out at pressures greater than 3 MPa and the low-pressure testing at pressures from 1,5 MPa to 3 MPa. The test procedure is applicable to hydraulic hose assemblies that are subject to pulsating pressures in service which are included in the product requirements. NOTE Impulse test procedures without flexing can be f...view more

    • sale 15% off
    • Standard
      7 pages
      English language
    • sale 15% off
    • Standard
      7 pages
      French language

ISO 28017:2018 specifies requirements for two types, seven classes and three grades of wire- or textile-reinforced dredging hoses with nominal sizes ranging from 100 to 1 200. Within each class, all grades and sizes have the same maximum working pressure. Such hoses are suitable for the delivery or suction of seawater or freshwater mixed with silt, sand, coral and small stones with a specific gravity in the range from 1,0 to 2,3 at ambient temperatures ranging from −10 °C to +40 °C. ISO 28017:20...view more

    • sale 15% off
    • Standard
      18 pages
      English language
    • sale 15% off
    • Standard
      20 pages
      French language

ISO 10619-1:2017 specifies three methods for measuring the flexibility of rubber and plastics hoses and tubing (methods A1, B and C1), where the deformation of the hose or tubing is measured, and two methods for measuring the stiffness (methods A2 and C2) by measuring the force required to bend rubber or plastics hoses or tubing to a specific radius at ambient temperature. Methods A1 and A2 are suitable for rubber and plastics hoses and tubing with inside diameter of up to and including 80 mm. M...view more

    • sale 15% off
    • Standard
      12 pages
      English language
    • sale 15% off
    • Standard
      13 pages
      French language

ISO 23297:2017 specifies requirements for eight classes and two types (construction with adhesive bond between layers and construction without adhesive bond between layers) of wire or synthetic yarn reinforced hydraulic hoses and hose assemblies of nominal size from 3,2 to 31,5. Each class has a single maximum working pressure for all sizes. Such hoses are suitable for use with hydraulic fluids HH, HL, HM, HR, and HV as defined in ISO 6743‑4 at temperatures ranging from −40 °C to +100 °C for gra...view more

    • sale 15% off
    • Standard
      13 pages
      English language

ISO 10619-2:2017 specifies two methods for measuring the stiffness and one method for the determination of the flexibility of rubber and plastics hoses and tubing when they are bent to a specific radius at sub-ambient temperatures. Method A is suitable for non-collapsible rubber and plastics hoses and tubing with a bore of up to and including 25 mm. This method provides a means of measuring the stiffness of the hose or tubing when the temperature is reduced from a standard laboratory temperature...view more

    • sale 15% off
    • Standard
      10 pages
      English language
    • sale 15% off
    • Standard
      10 pages
      French language

ISO 8028:2017 specifies the requirements for four types of hose and hose assemblies for use in airless paint spraying. The four types are differentiated by burst pressure and operating temperature, and can be constructed from rubber or plastic materials, or a combination of rubber and plastic material.

    • sale 15% off
    • Standard
      8 pages
      English language
    • sale 15% off
    • Standard
      8 pages
      French language

ISO 10960:2017 specifies a method of assessing the resistance of hoses to the deleterious effects of atmospheric ozone under dynamic conditions. It is applicable to hoses with bore diameters up to and including 25 mm.

    • sale 15% off
    • Standard
      3 pages
      English language
    • sale 15% off
    • Standard
      3 pages
      French language

ISO 1825:2017 specifies the dimensions and construction of, and requirements for, four types of hose and hose assembly for use in all operations associated with the ground fuelling and defuelling of aircraft. All four types are designed for: a) use with petroleum fuels having an aromatic-hydrocarbon content not exceeding 30 % by volume; b) operation within the temperature range of −30 °C to +65 °C and such that they will be undamaged by climatic conditions of −40 °C to +70 °C when stored in stat...view more

    • sale 15% off
    • Standard
      27 pages
      English language
    • sale 15% off
    • Standard
      29 pages
      French language

ISO 19385 specifies requirements for nine classes of reinforced hydraulic hoses and hose assemblies of nominal sizes ranging from 5 to 25. Each class has a single maximum working pressure. Such hoses and hose assemblies are intended to be used with very high-pressure water jetting and water blasting machines. ISO 19385 also reviews all the significant hazards, hazardous situations and events relevant to the equipment in the scope, when it is used as intended and under conditions of misuse which ...view more

    • sale 15% off
    • Standard
      13 pages
      English language
    • sale 15% off
    • Standard
      13 pages
      French language

ISO 16301 specifies the requirements for three classes of wire- or textile-reinforced hydraulic hoses and hose assemblies of nominal sizes ranging from 5 to 25. The hoses and hose assemblies are used in hydraulic jack applications with manually operated hand pumps. They are suitable for use with hydraulic fluids HH, HL, HM, HR and HV at temperature ranging from −40 °C to +55 °C. For tools that require heavy duty services such as a rescue tool, ISO 19718[3] applies. ISO 16301 does not include req...view more

    • sale 15% off
    • Standard
      17 pages
      English language

ISO 11237 specifies requirements for five types of compact, wire-braid-reinforced hose and hose assembly of nominal size from 5 to 31,5. They are suitable for use with - oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C; - water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from 0 °C to +60 °C; - water at temperatures ranging from 0 °C to +60 °C. ISO 11237 does not include requirements ...view more

    • sale 15% off
    • Standard
      11 pages
      English language

ISO 6806:2017 specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners. The following two types of hose assembly are specified. - Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 °C. - Type 2: Hose assemblies for insertion between the oil burner pump and the atomizing connection; maximum working pressure 4,0 MPa (...view more

    • sale 15% off
    • Standard
      14 pages
      English language
    • sale 15% off
    • Standard
      14 pages
      French language

ISO 6803:2017 describes hose impulse testing, without flexing, of rubber or plastics hydraulic hose assemblies at both high and low impulse pressures. The high-pressure testing is carried out at pressures greater than 3 MPa and the low-pressure testing at pressures from 1,5 MPa to 3 MPa. The test procedure is applicable to hydraulic hose assemblies that are subject to pulsating pressures in service which are included in the product requirements. NOTE Impulse test procedures with flexing can be f...view more

    • sale 15% off
    • Standard
      8 pages
      English language
    • sale 15% off
    • Standard
      8 pages
      French language

ISO 11424:2017 specifies requirements for rubber hoses and tubing for use in the various air and vacuum systems found on internal combustion engines. This document does not cover hoses used for direct power-brake actuation in trucks and trailers, nor for air intakes and ducting within the passenger compartment. The highest-temperature hoses are generally used for turbocharger applications. All hoses and tubing remain serviceable down to −40°C. NOTE Although the term vacuum is generally used, in ...view more

    • sale 15% off
    • Standard
      12 pages
      English language

ISO 6134:2017 specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high pressure with a maximum working pressure of 18 bar, made of rubber and hose fittings made of metal, designed to convey saturated steam and hot water condensate. Each type is divided into two classes having either an oil resistant or non-oil resistant cover. NOTE Information on the frequency of testing of hose assemblies in use and storage is given in Ann...view more

    • sale 15% off
    • Standard
      12 pages
      English language
    • sale 15% off
    • Standard
      13 pages
      French language

ISO 8033:2016 specifies methods for the determination of the adhesion between lining and reinforcement, between cover and reinforcement, between reinforcement layers, between cover and outer lamination (thin layer of material outside the cover for protection) and between lining and inner lamination (thin layer of material inside the lining to reduce permeation of fluid into the lining). It covers all bore sizes and the following types of hose construction: - woven textile fabric; - braided texti...view more

    • sale 15% off
    • Standard
      13 pages
      English language
    • sale 15% off
    • Standard
      13 pages
      English language
    • sale 15% off
    • Standard
      14 pages
      French language
    • sale 15% off
    • Standard
      14 pages
      French language

ISO 13775-2:2016 specifies test requirements and test methods for extruded thermoplastic tubing and hoses for use in petroleum-based-fuel lines in vehicles powered by internal-combustion engines.

    • sale 15% off
    • Standard
      19 pages
      English language
    • sale 15% off
    • Standard
      19 pages
      English language

ISO 4641:2016 specifies the minimum requirements for textile-reinforced, smooth-bore rubber water-suction and discharge hoses and hose assemblies. Three types of hoses and hose assemblies are specified according to their operating duty requirements, i.e. their ambient and water temperature ranges: - ambient temperatures: −25 °C to +70 °C; - water temperatures during operation: 0 °C to +70 °C.

    • sale 15% off
    • Standard
      11 pages
      English language
    • sale 15% off
    • Standard
      11 pages
      French language

ISO 6804:2016 specifies the requirements for three types of rubber or plastics inlet hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10 bar). It is applicable to the following types of hose: - type 1: rubber hoses for unheated water supply (maximum temperature 70 °C); - type 2: rubber hoses for heated water supply (maximum temperature 90 °C); - type 3: plastics hoses for unheated water supply (maximum temper...view more

    • sale 15% off
    • Standard
      13 pages
      English language

ISO 8331:2016 sets out recommendations designed to maintain rubber and plastics hoses and hose assemblies, prior to use, in a condition as close as possible to the condition they were in when they were received and to obtain the expected service life. NOTE It is intended that this document be used in conjunction with any applicable national statutory regulations.

    • sale 15% off
    • Standard
      13 pages
      English language
    • sale 15% off
    • Standard
      14 pages
      French language

ISO 1401:2016 specifies requirements for three types of flexible rubber hose for pressure spraying of agricultural chemicals and/or fertilizer products within a temperature range of ?10 °C to +60 °C.

    • sale 15% off
    • Standard
      8 pages
      English language
    • sale 15% off
    • Standard
      8 pages
      French language

ISO 2398:2016 specifies the requirements for three types, three classes and two categories of textile-reinforced rubber hose for compressed air, up to a maximum working pressure of 25 bar with an operating-temperature range of −40 °C to +70 °C, depending on the type and category.

    • sale 15% off
    • Standard
      8 pages
      English language
    • sale 15% off
    • Standard
      9 pages
      French language

ISO 7751:2016 specifies ratios of proof pressure and minimum burst pressure to maximum working pressure for various categories of hose service.

    • sale 15% off
    • Standard
      3 pages
      English language
    • sale 15% off
    • Standard
      3 pages
      French language

ISO 4081:2016 specifies the requirements for straight or pre-formed rubber hoses and tubing for use in pressurized or unpressurized cooling circuits containing 1,2-ethanediol-based coolants in internal-combustion engines for vehicles with an unladen mass (as defined in ISO 1176) of 3,5 t or less. In addition, this specification may also be applied as a classification system to enable original equipment manufacturers (OEMs) to detail a "line call-out" of tests for specific applications where thes...view more

    • sale 15% off
    • Standard
      15 pages
      English language

ISO 7326:2016 specifies five methods for determining the ozone resistance of the outer covers of hoses: - method 1, for bore sizes up to and including 25 mm, carried out on the hose itself; - method 2, for bore sizes greater than 25 mm, carried out on a test piece from the hose wall; - method 3, for bore sizes greater than 25 mm, carried out on a test piece from the cover; - method 4, for all bore sizes, carried out on the hose itself; - method 5, for all bore sizes, carried out on hoses that ar...view more

    • sale 15% off
    • Standard
      8 pages
      English language
    • sale 15% off
    • Standard
      8 pages
      French language

ISO 7233:2016 specifies three methods for determining the resistance to vacuum of hoses and hose assemblies manufactured from plastic or rubber. Applicable dimensions of hoses for each method are as follows: - method A for hoses of nominal bore up to and including 80 mm; - method B for hoses of nominal bore greater than 80 mm; - method C for hoses of all dimensions. Methods A and B can also be used to check the adhesion of the lining to the reinforcement (delamination) in a length of hard-wall h...view more

    • sale 15% off
    • Standard
      6 pages
      English language
    • sale 15% off
    • Standard
      6 pages
      French language

ISO 5774:2016 specifies the requirements for four types of flexible thermoplastic hose, textile reinforced, for compressed-air applications in the temperature range from −10 °C to +60 °C. The four types are classified as light service for a maximum working pressure of 7 bar at 23 °C and 4,5 bar at 60 °C, medium service for a maximum working pressure of 10 bar at 23 °C and 6,5 bar at 60 °C, heavy service for a maximum working pressure of 16 bar at 23 °C and 11 bar at 60 °C, and heavy service for ...view more

    • sale 15% off
    • Standard
      13 pages
      English language
    • sale 15% off
    • Standard
      13 pages
      French language

ISO 13363:2016 specifies requirements for three types and two classes of hose. The hoses are intended for use in marine-engine wet-exhaust systems (where the exhaust gases are mixed with the discharge of cooling water). It does not apply to outboard motor/personal water craft. The three types are the following: - type 1: a softwall hose, made of oil-resistant material, with a synthetic-fabric reinforcement; - type 2: a hardwall hose, made of oil-resistant material, with a synthetic-fabric reinfo...view more

    • sale 15% off
    • Standard
      9 pages
      English language
    • sale 15% off
    • Standard
      9 pages
      English language

ISO 19013-2:2016 specifies the requirements for rubber tubing and hoses used in gasoline fuel circuits for internal combustion engines. The gasoline fuels covered include those containing oxygenates such as methanol and fuels that have become oxidized ("sour gas"). In addition, this part of ISO 19013 can also be applied as a classification system to enable original equipment manufacturers (OEMs) to detail a "line call-out" of tests for specific applications where these are not covered by the mai...view more

    • sale 15% off
    • Standard
      22 pages
      English language

ISO 4642-2:2015 specifies the requirements and test methods for semi-rigid reel hoses for use on fire-fighting vehicles and trailer pumps. The hoses are intended for use at a maximum working pressure of 1,5 MPa for normal pressure hoses (category I) and 4,0 MPa for high pressure hoses (category II). The hoses are further subdivided into types and classes (see Clause 4). ISO 4642-2:2015 applies to delivery hoses for fire-fighting purposes intended for use at a minimum ambient temperature of −20 °...view more

    • sale 15% off
    • Standard
      29 pages
      English language

ISO 4642-1:2015 specifies the requirements and test methods for semi-rigid reel hoses for fire-fighting purposes for use with fixed systems. The hoses are intended for use at a maximum working pressure of 1,2 MPa for hoses of 19 mm and 25 mm inside diameter and 0,7 MPa for hoses of 33 mm inside diameter. Hoses conforming to this part of ISO 4642 are intended for applications where long intervals can occur between the occasions of use, for example on fixed fire hose reels in buildings and other c...view more

    • sale 15% off
    • Standard
      18 pages
      English language

ISO 13775-1:2015 specifies the test requirements and the test methods for extruded thermoplastic tubing and hoses for use in vehicles powered by internal-combustion engines, excluding use in air braking systems (see ISO 7628), fuel lines (see ISO 13775‑2), and high-pressure hydraulic systems. This part of ISO 13775 is intended especially for use by original equipment manufacturers (OEMs).

    • sale 15% off
    • Standard
      13 pages
      English language