This document establishes a classification of fan efficiency for all jet fan types driven by motors with an electrical input power range from 5,5 kW to 155 kW (and this is likely to be in the size range 500 mm to 1600 mm diameter with motors rated between 5,5 kW and 150 kW from IEC 60034-30-1). This document is not applicable to jet fans for use in enclosed car parks. This document can be used by legislators or regulatory bodies for defining future energy saving targets.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off
  • Draft
    9 pages
    English language
    sale 15% off
  • Draft
    9 pages
    French language
    sale 15% off

This document deals with the likely degradation of air performance of fans tested in standardized airways in accordance with ISO 5801 when compared with the performance of fans tested under actual site conditions. It deals with the performance of a number of generic types of fan and fittings. The results given are intended as guidelines and only provide trends, as the system effect depends on the exact geometry of the fan and disturbing component. The test data presented in this document are taken from an extensive experimental program conducted 20 years ago by NEL (National Engineering Laboratory, UK), mainly on axial and centrifugal fans. Data are also taken from several research projects financially supported by ASHRAE, some of them being carried out in the AMCA laboratory in Chicago, as well as from results published previously by individual fan manufacturers.

  • Technical report
    83 pages
    English language
    sale 15% off
  • Technical report
    87 pages
    French language
    sale 15% off
  • Draft
    83 pages
    English language
    sale 15% off

This document establishes a system for the classification of fan efficiency for all fan types driven by motors of nominal rating 0,125 kW and above. It applies to driven fans only, but not to the system (finished original equipment manufacturer's product, for example box fans and roof fans or ventilation system) in which they might be installed. This document describes a number of different procedures to classify the efficiency of a fan or to apply a minimum efficiency limit (MEL). Those procedures are described in: — ISO 12759-3; — this document (ISO 12759-4); — ISO 12759-5; — ISO 12759-6. There is no method described to compare these classifications and MEL's.

  • Standard
    25 pages
    English language
    sale 15% off
  • Standard
    26 pages
    French language
    sale 15% off

This document establishes a classification for fan efficiency. It applies to all electric-motor-driven fan systems that utilize a specific combination of components as defined below: a) fan airflow performance determined in accordance with an accepted performance standard; b) polyphase induction motors with nominal motor efficiency specified in this document; NOTE 1 Other types of motors are explicitly excluded. c) pulse-width modulated variable frequency drives (VFDs) for use with single motors; NOTE 2 Single VFDs that service multiple, parallel fan motors are excluded. d) mechanical power transmissions that utilize V-belts, flat belts, cog belts or couplings.

  • Standard
    21 pages
    English language
    sale 15% off
  • Standard
    21 pages
    French language
    sale 15% off

This document establishes a system for the classification of fan efficiency for all fan types which have a nominal fan shaft power rating of 0,125 kW and above. This document is applicable to fans only. It does not apply to drives or the system in which fans are installed. This document can be used by legislators or regulatory bodies for defining future energy saving targets.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off

ISO 5801:2017 specifies procedures for the determination of the performance of fans of all types except those designed solely for air circulation, e.g. ceiling fans and table fans. Testing of jet fans is described in ISO 13350. ISO 5801:2017 provides estimates of uncertainty of measurement and rules for the conversion, within specified limits, of test results for changes in speed, gas handled and, in the case of model tests, size are given.

  • Standard
    136 pages
    English language
    sale 15% off
  • Standard
    142 pages
    French language
    sale 15% off

ISO 13350:2015 deals with the determination of those technical characteristics needed to describe all aspects of the performance of jet fans as defined in ISO 13349. It does not cover those fans designed for ducted applications, nor those designed solely for air circulation, e.g. ceiling fans and table fans. The test procedures described in this International Standard relate to laboratory conditions. The measurement of performance under on-site conditions is not included.

  • Standard
    30 pages
    English language
    sale 15% off
  • Standard
    31 pages
    French language
    sale 15% off
  • Standard
    1 page
    English language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off

ISO 27327-2:2014 deals with the determination of the acoustic performance of air curtain units. In addition, it can be used to determine the acoustic performance of air curtain units combined with an ancillary device.

  • Standard
    38 pages
    English language
    sale 15% off
  • Standard
    38 pages
    English language
    sale 15% off
  • Standard
    1 page
    English language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off

ISO 13349:2010 defines terms and categories in the field of fans used for all purposes. It is not applicable to electrical safety.

  • Standard
    43 pages
    English language
    sale 15% off
  • Standard
    44 pages
    French language
    sale 15% off

ISO 13351:2009 specifies the dimensions of the circular and rectangular flanges of general‑purpose fans, as well as the fan size designations. It is not applicable to cross‑flow fans or to fan appliances used for individual household or similar applications.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    French language
    sale 15% off

ISO 27327-1:2009 establishes uniform methods for laboratory testing of air curtain units to determine aerodynamic performance in terms of airflow rate, outlet air velocity uniformity, power consumption and air velocity projection, for rating or guarantee purposes. ISO 27327-1:2009 is not applicable to the specification of test procedures to be used for design, production or field testing.

  • Standard
    29 pages
    English language
    sale 15% off

ISO 13348:2007 specifies performance tolerances and the technical data presentation of industrial fans of all types. It does not apply for fans designed solely for low-volume air circulation, such as those used for household or similar purposes (ceiling and table fans, extractor fans, etc.). ISO 13348:2007 covers the four installation categories defined in ISO 5801: A, free inlet, free outlet; B, free inlet, ducted outlet; C, ducted inlet, free outlet; D, ducted inlet, ducted outlet.

  • Standard
    53 pages
    English language
    sale 15% off
  • Standard
    55 pages
    French language
    sale 15% off

ISO 13347-2:2004 gives a detailed description of reverberant room methods for the determination of fan sound power levels. It is for use under standardized laboratory conditions and recognises that tests in situ are subject to increased uncertainty. These test procedures are not necessarily appropriate to site test conditions. Acoustic system effects are presently the subject of considerable research effort. ISO 5136, which covers the in-duct method, and ISO 10302 for small fans, should be used in conjunction with ISO 13347-2:2004.

  • Standard
    22 pages
    English language
    sale 15% off
  • Standard
    23 pages
    French language
    sale 15% off

ISO 13347-3:2004 applies to industrial fans as defined in ISO 5801 and ISO 13349. It is limited to the determination of airborne sound emission for the specified set-ups. Vibration is not measured, nor is the sensitivity of airborne sound emission to vibration effects determined. The sizes of fan which can be tested in accordance with ISO 13347-3:2004 are limited only by the practical aspects of the test set-up. Dimensional limitations, test fan dimensions, and air performance will control the room size, power and mounting requirements for the test fan. The test arrangements in ISO 13347-3:2004 establish the laboratory conditions necessary for a successful test. Rarely will it be possible to meet these requirements in situ and ISO 13347-3:2004 is not intended for field measurements. Intending users are reminded that, in these situations, there may well be additional acoustic system effects where inlet and outlet conditions at the fan are less than ideal. The enveloping surface methods may be used for the determination of open inlet and/or open outlet sound power level of fans for standardized installation types. An estimation (with increased uncertainty) of ducted sound power for fans too small, or otherwise inconvenient, for testing by the in-duct method described in ISO 5136 may also be obtained by the addition of end reflection corrections.

  • Standard
    22 pages
    English language
    sale 15% off
  • Standard
    23 pages
    French language
    sale 15% off

ISO 13347-4:2004 applies to industrial fans as defined in ISO 5801 and ISO 13349. It is limited to the determination of airborne sound emission for the specified set-ups. Vibration is not measured, nor is the sensitivity of airborne sound emission to vibration effects determined. The sizes of the fan, which can be tested in accordance with ISO 13347-4:2004, are limited only by the practical aspects of the test installations. ISO 13347-4:2004 determines sound power by using sound intensity measurements on a measurement surface which encloses the sound source. It provides guidelines on the acoustical environment, ambient noise, measurement surface, and number of measurements. The test set-ups are generally designed to represent the physical orientation of a fan installed in accordance with ISO 5801 and also used in ISO 13347-2.

  • Standard
    25 pages
    English language
    sale 15% off
  • Standard
    26 pages
    French language
    sale 15% off

ISO 13347:2004 deals with the determination of the acoustic performance of industrial fans. In addition, it may be used to determine the acoustic performance of fans combined with an ancillary device such as a roof cowl or damper or, where the fan is fitted with a silencer, the sound power resulting from the fan and silencer combination.

  • Standard
    34 pages
    English language
    sale 15% off
  • Standard
    36 pages
    French language
    sale 15% off

ISO 14695:2003 describes a method of measuring the vibrational characteristics of fans of all types, except those designed solely for air circulation, for example, ceiling fans and table fans. However, it is limited to fans of all types installed with a power of less than 300 kW. For fans of greater power than this, the methods described in ISO 10816-1 and the applicable limits given in ISO 10816-3 may be used. ISO 14695:2003 gives a general method only and does not give criteria for interpretation of data (see ISO 14694). ISO 14695:2003 specifies the measurement of vibration that may be recorded as overall root-mean- square (r.m.s.) velocity, acceleration or displacement, or in terms of a frequency spectrum, within the appropriate frequency range. Methods of testing when suspended on elastic ropes or when installed on resilient mountings are included. It is recognized that the oscillatory forces at mounting points can be a useful measurement for analysing the effects on support structures; but such measurements are outside the scope of ISO 14695:2003.

  • Standard
    33 pages
    English language
    sale 15% off
  • Standard
    34 pages
    French language
    sale 15% off

ISO 14694:2003 gives specifications for vibration and balance limits of fans for all applications except those designed solely for air circulation, for example, ceiling fans and table fans. However, it is limited to fans of all types installed with a power of less than 300 kW or to commercially available standard electric motor with a maximum power of 355 kW (following an R20 series). For fans of greater power than this, the applicable limits are those given in ISO 10816 - 3. Where the fans in an installation have varying powers both above and below 300 kW, and have been the subject of a single contract, then the manufacturer and purchaser shall agree on the appropriate standard to be used. This should normally be based on the majority of units. Fan-equipment foundations and installation practices are beyond the scope of ISO 14694:2003. Foundation design and fan installation are not normally the responsibilities of the fan manufacturer. It is fully expected that the foundations upon which the fan is mounted will provide the support and stability necessary to meet the vibration criteria of the fan as it is delivered from the factory. ISO 14694:2003 is intended to cover only the balance or vibration of the fan and does not take into account the effect of fan vibration on personnel, equipment or processes.

  • Standard
    39 pages
    English language
    sale 15% off
  • Standard
    42 pages
    French language
    sale 15% off
  • Standard
    86 pages
    English language
    sale 15% off
  • Standard
    88 pages
    French language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    16 pages
    French language
    sale 15% off
  • Draft
    26 pages
    English language
    sale 15% off
  • Draft
    26 pages
    English language
    sale 15% off
  • Draft
    27 pages
    French language
    sale 15% off
  • Standard
    1 page
    English language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off

ISO 12759:2010 specifies requirements for classification of fan efficiency for all fan types driven by motors with an electrical input power range from 0,125 kW to 500 kW. It is applicable to (bare shaft and driven) fans, as well as fans integrated into products. Fans integrated into products are measured as stand-alone fans. It is not applicable to fans for smoke and emergency smoke extraction; fans for industrial processes; fans for automotive application, trains, planes, etc.; fans for potentially explosive atmospheres; box fans, powered roof ventilators and air curtains or jet fans for use in car parks and tunnel ventilation.

  • Standard
    42 pages
    English language
    sale 15% off
  • Standard
    45 pages
    French language
    sale 15% off

ISO 5801:2007 deals with the determination of the performance of industrial fans of all types except those designed solely for air circulation e.g. ceiling fans and table fans. Estimates of uncertainty of measurement are provided and rules for the conversion, within specified limits, of test results for changes in speed, gas handled and, in the case of model tests, size, are given.

  • Standard
    228 pages
    English language
    sale 15% off
  • Standard
    236 pages
    French language
    sale 15% off

ISO 13348:2006 specifies performance tolerances and the technical data presentation of industrial fans of all types. It does not apply for fans designed solely for low-volume air circulation, such as those used for household or similar purposes (ceiling and table fans, extractor fans, etc.). ISO 13348:2006 covers the four installation categories defined in ISO 5801:A, free inlet, free outlet; B, free inlet, ducted outlet; C, ducted inlet, free outlet;D, ducted inlet, ducted outlet.

  • Standard
    53 pages
    English language
    sale 15% off
  • Standard
    55 pages
    French language
    sale 15% off

ISO 6580:2005 specifies the dimensions of circular flanges for general-purpose industrial fans

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    39 pages
    English language
    sale 15% off
  • Standard
    37 pages
    French language
    sale 15% off
  • Standard
    27 pages
    English language
    sale 15% off
  • Standard
    25 pages
    French language
    sale 15% off
  • Standard
    232 pages
    English language
    sale 15% off
  • Standard
    237 pages
    French language
    sale 15% off
  • Standard
    237 pages
    French language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    French language
    sale 15% off
  • Standard
    10 pages
    French language
    sale 15% off

Specifies the dimensions of circular flanges for industrial fans. It does not apply to heavy duty types with greater flange thickness. It adopts the R 20 Series as per ISO 497.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    French language
    sale 15% off
  • Standard
    2 pages
    French language
    sale 15% off