This document specifies the requirements for solid-wall styrene copolymer blend (SAN + PVC) pipes and fittings for soil and waste discharge (low and high temperature) above ground inside buildings, and for the system itself. It does not include buried pipework. It also specifies the test parameters for the test methods referred to within this document. This document is applicable to SAN + PVC pipes and fittings, as well as assemblies of such pipes and fittings, intended to be used for the following purposes: a) soil and waste discharge pipework for the conveyance of domestic waste waters (low and high temperature); b) ventilation pipework associated with a); c) rainwater pipework inside the building. This document is applicable to pipes and fittings designed for jointing by means of elastomeric sealing rings, solvent cementing or integral dual-purpose sockets, i.e. for elastomeric ring seal joints and/or for solvent cement joints.

  • Standard
    30 pages
    English language
    sale 15% off
  • Draft
    30 pages
    English language
    sale 15% off

This document specifies a test method for determining the leaktightness of elastomeric sealing ring type joints for buried thermoplastics non-pressure piping systems. Unless otherwise specified in the referring standard, the tests are carried out at the following basic test pressures: — p1: internal negative air pressure (partial vacuum); — p2: a low internal hydrostatic pressure; — p3: a higher internal hydrostatic pressure. It also describes the following four test conditions under which the tests are performed: a) Condition A: without any additional diametric or angular deflection; b) Condition B: with diametric deflection; c) Condition C: with angular deflection; d) Condition D: with simultaneous angular and diametric deflection. The applicable selection of the test pressure(s) and the test condition(s) is/are specified in the referring standard.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    11 pages
    French language
    sale 15% off
  • Draft
    10 pages
    English language
    sale 15% off

This document, together with ISO 21138‑1, specifies the definitions and requirements for pipes with a non-smooth external surface and a smooth internal surface (Type B), fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems intended to be used in non-pressure underground drainage and sewerage applications. NOTE 1 Pipes, fittings and the systems complying with this document can also be used for highway drainage and surface water. This document specifies test methods and test parameters. This document covers a range of pipe and fitting sizes, materials, pipe constructions and nominal ring stiffnesses, and gives recommendations concerning colours. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes. In conjunction with ISO 21138‑1, this document is applicable to structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials. It is applicable to pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. NOTE 3 Pipes, fittings and other components conforming to any plastics product standards referred to in Clause 2 are deemed to be suitable for use with pipes and fittings conforming to this document, when they conform to the requirements for joint dimensions given in ISO 21138‑2 or ISO 21138‑3 (this document) and to the performance requirements given in Clause 10. NOTE 4 For dimensions larger than DN/OD 1200 or DN/ID 1200, this document can serve as general guidance regarding appearance, colour, physical and mechanical characteristics as well as performance requirements. Test methods are not included in this document.

  • Standard
    38 pages
    English language
    sale 15% off

This document, together with ISO 21138‑2 and ISO 21138‑3, specifies the definitions and requirements for pipes, fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems intended to be used in non-pressure underground drainage and sewerage applications. NOTE 1 Pipes, fittings and the system complying with this document can also be used for highway drainage and surface water. This document covers a range of pipe and fitting sizes, materials, pipe constructions, nominal ring stiffnesses, and gives recommendations concerning colours. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes. In conjunction with ISO 21138‑2 and ISO 21138‑3, this document is applicable to structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials. It is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. NOTE 3 Pipes, fittings and other components conforming to any plastics product standards referred to in the Bibliography can be used with pipes and fittings conforming to this document when they conform to the requirements for joint dimensions given in ISO 21138-2 and ISO 21138-3 and to the performance requirements given in Clause 9. NOTE 4 For dimensions larger than DN/OD 1200 or DN/ID 1200, this document can serve as a general guideline regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.

  • Standard
    17 pages
    English language
    sale 15% off

This document, together with ISO 21138-1, specifies the definitions and requirements for pipes with smooth external and internal surfaces (Type A), fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems intended to be used in non-pressure underground drainage and sewerage applications. NOTE 1 Pipes, fittings and the system complying with this document can also be used for highway drainage and surface water. This document specifies test methods and test parameters. This document covers a range of pipe and fitting sizes, materials, pipe constructions and nominal ring stiffnesses, and gives recommendations concerning colours. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes. In conjunction with ISO 21138-1, this document is applicable to structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials. It is applicable to pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. NOTE 3 For dimensions larger than DN/OD 1200, or DN/ID 1200, this document can serve as general guidance regarding appearance, colour, physical and mechanical characteristics as well as performance requirements. Test methods are not included in this document.

  • Standard
    39 pages
    English language
    sale 15% off

This document specifies a test method for determining the resistance to elevated temperature cycling of thermoplastics piping systems for non‑pressure applications, inside buildings or buried in the ground within the building structure. This document is applicable to piping systems with components of nominal outside diameters up to and including 200 mm. Although limited to nominal outside diameters up to and including 200 mm, the test results may be extrapolated to products of larger nominal outside diameters from the same range.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    French language
    sale 15% off

ISO/TS 17902:2016 specifies the definitions and requirements for wrapped electrofoaming joints for polyethylene (PE) piping systems with smooth outer wall for underground drains and sewer without pressure. ISO/TS 17902:2016 specifies product range, material characteristics, test methods and test parameters, dimension and characteristics of wrap. ISO/TS 17902:2016 is applicable to jointing pipes which have external wall thickness greater than 1,4 mm and a diameter up to DN/OD 2000, or DN/ID 2200.

  • Technical specification
    13 pages
    English language
    sale 15% off

ISO 15398:2012 specifies the definitions and requirements for thermoplastics covers and frames for inspection chambers and other such pipeline access products installed in light vehicular access and pedestrian areas and manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE). The products are rated up to B 125 max. and are intended for use either inside or outside buildings including swimming pool areas but are not intended for use in the carriageway of trafficked areas. It is only applicable to those covers and frames where the manufacturer has clearly stated in the documentation how the frames are installed and assembled to the intended access product, identifying as necessary the manufacturer and grades of product or riser to which the frame is intended to fit.

  • Standard
    15 pages
    English language
    sale 15% off

ISO 13272:2011 specifies the definitions and requirements for buried manholes and inspection chambers (circular or non-circular) installed to a maximum depth of 6 m from ground level to the invert of the main chamber and manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifiers (PP-MD) or polyethylene (PE). These products are intended for use in traffic areas and underground installations conforming to the general requirements given in EN 476 and are used outside the building structure (application area code "U"). They are therefore marked accordingly with a "U". ISO 13272:2011 is only applicable to those chamber/manhole items where the manufacturer has clearly stated in the documentation how the components shall be assembled to create a complete manhole or inspection chamber. The inspection chambers covered by ISO 13272:2011 comprise the following: inspection chambers providing access to the drainage or sewerage system by means of inspection and cleaning equipment; chambers designated as manholes providing man access to the drainage or sewerage system.

  • Standard
    20 pages
    English language
    sale 15% off
  • Standard
    23 pages
    French language
    sale 15% off

ISO 13260:2010 specifies two methods for testing pipes and fittings or joints for plastics piping systems intended for use in underground drainage and sewerage systems for their resistance to deformation and leakage, when subjected to sustained external loading in conjunction with the passage of hot water.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    French language
    sale 15% off

ISO 13268:2010 specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off

ISO 13264:2010 specifies a method for testing the mechanical strength or flexibility of a fabricated thermoplastic fitting intended to be used in non-pressure underground applications.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off

ISO 13265:2010 specifies a method for the determination of the long-term sealing pressure of elastomeric seals in assembled joints for buried non-pressure sewerage plastics piping and ducting systems.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    French language
    sale 15% off

ISO 13267:2010 specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    10 pages
    French language
    sale 15% off

ISO 13266:2010 specifies a method of testing the resistance of the upper assembly of inspection chambers and manhole components against surface and traffic loading. It is not applicable to requirements for testing the cover and frame.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off

ISO 13262:2010 specifies a method for determining the tensile strength of a seam in a spirally-formed thermoplastics pipe. It is applicable to all such thermoplastics pipes, regardless of their intended use

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

ISO 13255:2010 specifies a method for testing the airtightness of joints of thermoplastics piping systems for soil and waste discharge inside buildings.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

ISO 13254:2010 specifies a test method for watertightness of thermoplastics products fabricated from more than one piece for non-pressure applications, and joints of thermoplastics piping systems for non-pressure applications.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off

ISO 13263:2010 specifies a method for testing the impact resistance of fittings by dropping them on to a rigid surface. For a fitting with seal-retaining components, such as seal-retaining caps or rings, the method includes assessment of the watertightness of the fittings when the fixing elements show disturbance as a result of the test. It is applicable to fittings made from thermoplastics materials intended to be used for buried and above-ground applications.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off

ISO 13229:2010 specifies a method for the determination of the viscosity number (also known as reduced viscosity) and K-value of an unplasticized poly(vinyl chloride) (PVC) resin derived from a pipe, fitting or compound. In ISO 13229:2010, only the method for isolation (or separation) of the PVC resin is detailed.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off

ISO 8772:2006 specifies the requirements for polyethylene (PE) pipes, fittings and piping systems intended for use for non-pressure underground drainage and sewerage for the conveyance of soil and waste discharge of domestic and industrial origin, as well as surface water. It covers buried pipework, as well as piping systems buried within the building structure. In the case of industrial discharge, it is necessary that the chemical and temperature resistance be taken into account, but this will need to be done separately. ISO 8772:2006 is applicable to PE pipes with or without an integral socket. This International Standard is applicable to PE pipes and fittings for the following types of joints: elastomeric ring seal joints; butt fused joints; electrofusion joints; mechanical joints. ISO 8772:2006 also specifies the test parameters for the test methods referred to therein.

  • Standard
    22 pages
    English language
    sale 15% off
  • Standard
    23 pages
    French language
    sale 15% off

ISO 8773:2006 specifies the requirements for polypropylene (PP) pipes, fittings and piping systems intended for use for non-pressure underground drainage and sewerage for the conveyance of soil and waste discharge of domestic and industrial origin, as well as surface water. It covers buried pipework, as well as piping systems buried within the building structure. In the case of industrial discharge, it is necessary that the chemical and temperature resistance be taken into account, but this will need to be done separately. ISO 8773:2006 is applicable to PP pipes with or without an integral socket and to jointing by means of push fit joints with sealing rings or butt-fused joints. It covers PP materials with normal E moduli and with higher E moduli, designated as HM (higher modulus), and gives a range of nominal sizes and pipe series, as well as recommendations concerning colours. ISO 8773:2006 also specifies the test parameters for the test methods referred to therein.

  • Standard
    22 pages
    English language
    sale 15% off
  • Standard
    23 pages
    French language
    sale 15% off

ISO/TS 7024:2005 gives the recommended practice for installation of thermoplastic piping systems in the field of soil and waste discharge (low and high temperature) inside buildings (marked with "B"). ISO/TS 7024:2005 is applicable to thermoplastic pipes and fittings as specified in the associated standards ISO 3633 (PVC-U), ISO 7671 (PP), ISO 7682 (ABS), ISO 8770 (PE-HD), ISO 19220 (SAN+PVC) and ISO 7675 (PVC-C), their joints and to joints with components of other plastic and non-plastic materials intended to be used for the following purposes: soil and waste discharge pipework for the conveyance of domestic waste waters (low and high temperature); ventilating pipework associated with 1); rainwater pipework within the building structure. If specified in the relevant associated standard, ISO/TS 7024:2004 also covers soil and waste discharge pipework fixed externally on to the building. It is not applicable to pipework that passes under the building without any connection from the discharge system.

  • Technical specification
    42 pages
    English language
    sale 15% off
  • Technical specification
    43 pages
    French language
    sale 15% off

ISO 7671:2003 specifies the requirements for solid-wall polypropylene (PP) pipes and fittings for soil and waste discharge (low and high temperature) inside buildings, as well as the system itself. It does not include buried pipework. It is applicable to pipes and fittings for jointing by means of elastomeric sealing rings or by butt fusion.

  • Standard
    25 pages
    English language
    sale 15% off
  • Standard
    25 pages
    French language
    sale 15% off

ISO 8770:2003 specifies the requirements for solid-wall polyethylene (PE) pipes and fittings for soil and waste discharge (low and high temperature) inside buildings, as well as the system itself. It does not include buried pipework. It is applicable to pipes and fittings designed for jointing by means of elastomeric sealing rings or by butt fusion or electrofusion.

  • Standard
    24 pages
    English language
    sale 15% off
  • Standard
    25 pages
    French language
    sale 15% off

ISO 7682:2003 specifies the requirements for solid-wall acrylonitrile-butadiene-styrene (ABS) pipes and fittings for soil and waste discharge (low and high temperature) inside buildings, as well as the system itself. It does not include buried pipework. It is applicable to pipes and fittings designed for jointing by means of elastomeric sealing rings, solvent cementing or integral dual-purpose sockets, i.e. for elastomeric ring seal joints and/or for solvent cement joints.

  • Standard
    30 pages
    English language
    sale 15% off
  • Standard
    30 pages
    French language
    sale 15% off

ISO 7675:2003 specifies the requirements for chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings for soil and waste discharge (low and high temperature) inside buildings, as well as the system itself. It does not include buried pipework. It is applicable to pipes and fittings designed for jointing by means of elastomeric sealing rings, solvent cementing or integral dual-purpose sockets, i.e. for elastomeric ring seal joints and/or for solvent cement joints.

  • Standard
    30 pages
    English language
    sale 15% off
  • Standard
    30 pages
    French language
    sale 15% off

ISO 4435:2003 specifies the requirements for unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and piping systems intended for use for non-pressure underground drainage and sewerage for the conveyance of soil and waste discharge of domestic and industrial origin, as well as surface water. It covers buried pipework but does not apply to piping systems buried within the building structure. It is applicable to PVC-U pipes with or without an integral socket.

  • Standard
    22 pages
    English language
    sale 15% off
  • Standard
    24 pages
    French language
    sale 15% off

This International Standard specifies the requirements for unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings for soil and waste discharge (low and high temperature) inside buildings, as well as the system itself. It does not include buried pipework. It also specifies the test parameters for the test methods referred to in this International Standard. This International Standard is applicable to PVC-U pipes and fittings, as well as assemblies of such pipes and fittings, intended to be used for the following purposes: soil and waste discharge pipework for the conveyance of domestic waste waters (low and high temperature); ventilation pipework associated with 1; rainwater pipework inside the building.

  • Standard
    29 pages
    English language
    sale 15% off
  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    29 pages
    French language
    sale 15% off

Specifies requirements for traps for discharge pipework systems for domestic use within buildings, i. e. pipework systems for the discharge of domestic waste waters.

  • Standard
    27 pages
    English language
    sale 15% off
  • Standard
    28 pages
    French language
    sale 15% off
  • Standard
    28 pages
    French language
    sale 15% off

Specifies the design formulae and the derived dimensions, together with tolerances, of sockets and spigots for joints and for integral sockets of PP pipes intended for use in discharge systems inside buildings where such joints are intended to accommodate expansion and contraction.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

Specifies the design formulae and the derived dimensions, together with tolerances, of sockets and spigots for joints of PE fittings and for integral sockets of PE pipes intended for use in discharge systems inside buildings where such joints are intended to accommodate expansion and contraction. Sockets and spigots for thermal and electrothermal welding are excluded.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

Establishes a classification (ring-seal sockets and solvent cement sockets) and designation system (types S, M, L, and CS) for sockets and specifies the design formulae and the derived dimensions, together with tolerances, of these sockets and of spigots for joints and for integral sockets of ABS pipes intended for use in discharge systems inside buildings where such joints are intended to accommodate expansion and contraction.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off

Establishes a classification and designation system for sockets and specifies the design formulae and the derived dimensions, together with tolerances, of these sockets and of spigots for joints. Annexes A and B form an integral part of this standard.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    9 pages
    French language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off

Specifies the series of diameters and the formulae for calculation of the dimensions common to the main types of fittings with spigot ends (socket fittings with curved entries and branches) made of PVC-U.

  • Standard
    20 pages
    English language
    sale 15% off
  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    20 pages
    French language
    sale 15% off
  • Standard
    20 pages
    French language
    sale 15% off

This document specifies a test method for determining the leak tightness of elastomeric sealing ring type joints for buried thermoplastics non-pressure piping systems. Unless otherwise specified in the referring standard, the tests are carried out at the following basic test pressures: — p1: internal negative air pressure (partial vacuum); — p2: a low internal hydrostatic pressure; — p3: a higher internal hydrostatic pressure. It also describes the following four test conditions under which the tests are performed: a) Condition A: without any additional diametric or angular deflection; b) Condition B: with diametric deflection; c) Condition C: with angular deflection; d) Condition D: with simultaneous angular and diametric deflection. The applicable selection of the test pressure(s) and the test condition(s) is specified in the referring standard

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    11 pages
    French language
    sale 15% off

ISO 13257:2010 specifies a method for testing the resistance of thermoplastics piping systems for soil and waste discharge inside buildings, application area "B", or buried in the ground within the building structure, application areas "BD" or "UD", to 1 500 cycles of elevated temperature cycling.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off

ISO 13259:2010 specifies three basic test pressures for determining the leaktightness of elastomeric sealing ring type joints for buried thermoplastics non-pressure piping systems. It also describes four conditions under which the test can be executed.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off

ISO 21138-3:2007, together with ISO 21138-1, specifies the definitions and requirements for pipes with a non-smooth external surface (Type B), fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems in the field of non-pressure systems for underground drainage and sewerage. ISO 21138-3:2007 specifically refers to PVC, PP and PE materials. ISO 21138-3:2007 specifies test methods and test parameters. ISO 21138-3:2007 covers a range of pipe and fitting sizes, materials, pipe constructions and nominal ring stiffnesses, and gives recommendations concerning colours. In conjunction with ISO 21138-1, it is applicable to PVC-U, PP and PE structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for the transport of drainage and sewage. ISO 21138-3:2007 is applicable to PVC-U, PP and PE structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.

  • Standard
    39 pages
    English language
    sale 15% off
  • Standard
    42 pages
    French language
    sale 15% off

ISO 21138-2:2007, together with ISO 21138-1, specifies the definitions and requirements for pipes with a smooth external surface (Type A), fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping in the field of non-pressure systems for underground drainage and sewerage. ISO 21138-2:2007 specifically refers to PVC, PP and PE materials ISO 21138-2:2007 specifies test methods and test parameters. ISO 21138-2:2007 covers a range of pipe and fitting sizes, materials, pipe constructions, and nominal ring stiffnesses, and gives recommendations concerning colours. In conjunction with ISO 21138-1, it is applicable to PVC-U, PP and PE structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for the transport of drainage and sewage. ISO 21138-2:2007 is applicable to PVC-U, PP and PE structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.

  • Standard
    41 pages
    English language
    sale 15% off
  • Standard
    42 pages
    French language
    sale 15% off

ISO 21138-1:2007 specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems in the field of non-pressure underground systems for underground drainage and sewerage. ISO 21138-1:2007 specifically refers to PVC, PP and PE materials. ISO 21138-1:2007 covers a range of pipe and fitting sizes, materials, pipe constructions, nominal ring stiffnesses, and gives recommendations concerning colours. In conjunction with ISO 21138-2 and ISO 21138-3, it is applicable to PVC-U, PP and PE structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for the transport of drainage and sewerage. ISO 21138-1:2007 is applicable to PVC-U, PP and PE structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. For dimensions larger than DN/OD 1200 or DN/ID 1200, ISO 21138-1:2007 can serve as a general guide regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    19 pages
    French language
    sale 15% off

ISO 19220:2004 specifies the requirements for solid-wall styrene copolymer blend (SAN + PVC) pipes and fittings for soil and waste discharge (low and high temperature) above ground inside buildings, as well as the system itself. It does not include buried pipework. It is applicable to pipes and fittings designed for jointing by means of elastomeric sealing rings, solvent cementing or integral dual-purpose sockets, i.e. for elastomeric ring seal joints and/or for solvent cement joints.

  • Standard
    32 pages
    English language
    sale 15% off
  • Standard
    31 pages
    French language
    sale 15% off
  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    18 pages
    French language
    sale 15% off
  • Standard
    18 pages
    French language
    sale 15% off
  • Standard
    15 pages
    English language
    sale 15% off
  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    15 pages
    French language
    sale 15% off
  • Standard
    15 pages
    French language
    sale 15% off
  • Standard
    17 pages
    English language
    sale 15% off
  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    17 pages
    French language
    sale 15% off
  • Standard
    17 pages
    French language
    sale 15% off
  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    French language
    sale 15% off
  • Standard
    19 pages
    French language
    sale 15% off
  • Standard
    15 pages
    English language
    sale 15% off
  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    15 pages
    French language
    sale 15% off
  • Standard
    15 pages
    French language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    14 pages
    French language
    sale 15% off
  • Standard
    14 pages
    French language
    sale 15% off
  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    French language
    sale 15% off
  • Standard
    19 pages
    French language
    sale 15% off