This document specifies a method for determining the adhesion of a bituminous emulsion coated onto aggregate when immersed in water.
The method considers two different aspects of adhesivity, i.e. immediate adhesivity and water effect on binder adhesion.
The method may be used with a reference aggregate. In that case, it measures the intrinsic adhesion behaviour of a bituminous emulsion. The method may also be used with a specific aggregate as used on a job site.
WARNING -The use of this document may involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document describes a method for the determination of the free acidic constituents present in bitumen, conventionally known as acid number.
WARNING - The use of this document may involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Technical specification
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical specification
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document describes a method for determination of the salt content in bitumen, conventionally expressed in mg of sodium chloride (noted NaCl as from this point of this document) per kg of bitumen. This method is valid for "equivalent NaCl contents" between 20 mg/kg and 500 mg/kg.
WARNING - The use of this document may involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Technical specification
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical specification
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document provides examples of Declaration of Performance (DoP) and CE Marking for bitumen and bituminous binders for use in the construction and maintenance of roads, airfields and other paved areas.
NOTE 1   Only harmonised technical specifications (product standards or ETAs) cited in the OJEU are the basis for drawing up the Declaration of Performance.
NOTE 2   The product standards this document is related to, are listed in the bibliography.
NOTE 3   The EC database of all harmonized standards is available at
https://ec.europa.eu/growth/tools-databases/nando/index.cfm?fuseaction=cp.hs&cpr=Y.

  • Technical report
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical report
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies a method for the determination of the distillation characteristics of cut-back and fluxed bituminous binders made with mineral fluxes.
WARNING - The use of this European Standard can involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies methods for the determination of the thickness and mass per unit area of plastic and rubber sheets for roof waterproofing.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard is one of a series of standards applicable to flexible sheets for waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles.
This document specifies:
-   the composition, the characteristics and the preparation procedure of the base specimen concrete slabs;
-   the composition, the characteristics and the preparation procedure of different bituminous mixtures for the asphalt layer;
-   the rules for the preparation of specimens.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the determination of tear properties of plastic and rubber sheets for roof waterproofing using a trapezoidal test specimen with a nick or cut.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the stabilisation at 85 °C for 24 h of a binder after recovery from a bituminous emulsion or from a cut-back or fluxed bitumen for further testing.
It applies to all types of bituminous emulsions, modified with polymers or non-modified, and as well as to all types of cut-back and fluxed bitumen, both modified with polymers and non-modified.
The recovery test method is specified in EN 13074-1.
WARNING - The use of this document may involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. The hazards associated with the use of this method have been assessed using cut-back bitumen containing 10 % kerosene and 90 % 160/220 penetration grade bitumen and were found low enough to be acceptable. However it is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the recovery of binder from a bituminous emulsion or from a cut-back or fluxed bitumen after conditioning at ambient temperature for 24 h followed by 24 h at 50 °C, in such a way that will enable further testing with minimum changes of the binder characteristics.
It applies to all types of bituminous emulsions, modified with polymers or non-modified, as well as to all types of cut-back and fluxed bitumen, both modified with polymers and non-modified.
For cut-back and fluxed bituminous binders, this test method is only an intermediate step and should be followed by the stabilisation procedure specified by EN 13074-2. Direct testing of the recovered binder is however used to evaluate the setting ability of fluxed bituminous binders made with vegetal fluxes.
NOTE   The recovered binder is not necessarily identical to the initial binder.
WARNING - The use of this document may involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. The hazards associated with the use of this method have been assessed using cut-back bitumen containing 10 % kerosene and 90 % 160/220 penetration grade bitumen and were found low enough to be acceptable. However it is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a test method to determine the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing.
The assessment is limited to the performance of the mechanically fastened flexible sheets only. The test method does not include the determination of the performance of the mechanical fastener and/or the combination of the mechanical fastener and the substrate.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard gives a calculation method of the Solar Reflectance Index (SRI) and the determination of solar reflectivity and thermal emissivity for waterproofing flexible sheets for roofs with a slope smaller than 10°.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for determining the dynamic viscosity of a bituminous binder over a range of temperatures by means of a cone and plate viscometer. The test method is intended for all bituminous binders (e.g paving grade bitumen and polymer modified). It is also suitable for recovered bituminous binders according to EN 12697 3 and EN 12697 4 with no or limited amount of filler.
WARNING - The use of this European Standard can involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the determination of the dynamic viscosity of a variety of bituminous binders: modified and unmodified bituminous binders, bituminous emulsions, cut-back and fluxed bituminous binders, by means of a coaxial viscometer.
Standard application temperatures are quoted, although the dynamic viscosity can be measured at other temperatures if required. Similarly, viscosity is quoted at standard rates of shear, although additional measures can be taken at varying shear rates if required.
WARNING  The use of this standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for determining the tensile properties of a bituminous binder, in particular those of polymer-modified bitumens by means of a force ductility test.
The work done during the force ductility test is a criterion for assessing the quality of these materials.
WARNING - The use of this European Standard may involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Nacionalni standard opredeljuje nacionalne zahteve, ki dopolnjujejo evropske standarde, niso pa z njimi v ničemer v nasprotju. V standardu so jasno postavljena merila za bistvene lastnosti materialov glede na zahtevne podnebne razmere v naši državi.

  • Standard
    19 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the quantitative determination of residual binder and oil distillate in bituminous emulsions. The method can also be used to obtain residue and oil distillate for further testing. NOTE The properties of the material recovered in the test are not necessarily the same as those of the original materials from which the emulsion was produced, especially for polymer modified bitumens. WARNING — The use of this standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a test for puncture by impact on sheets for roof waterproofing. Mechanical stress on waterproofing sheets ranges from static long-term loads to dynamic short-term loads. This method represents the dynamic category of load where puncture may be caused by impact.
This European Standard may also be applied for other purposes of waterproofing.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies a method for determining the extrudability of sealants independently of the
package in which they are supplied.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for measuring the storage stability at high temperatures.
NOTE   Modified bitumen and, in particular, polymer-modified bitumen, which consist of mainly bitumen and at least one additional agent, are known to display phase separation under certain conditions.
WARNING - The use of this European Standard can involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the determination of the elastic recovery of bituminous binders in a ductilometer at the test temperature (typically 25°C or 10°C; other temperatures can be used).
It is especially applicable to bituminous binders modified with thermoplastic elastomers, but can also be used with other bituminous binders which generate only small recovery.
WARNING - The use of this European Standard may involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for measuring the cohesion of bituminous binders for surface dressing application at temperatures in the range of (- 10 oC) to (+ 80 °C) and for expressing the relationship between cohesion and temperature.
This method is applicable for pure bitumen, modified bitumen and fluxed bitumen; in the case of fluxed bitumen, the test can be performed on the binder containing fluxant or on binder from which the solvent has been removed. For bitumen emulsions, the test is carried out on the residual binder obtained after recovery and the method used to recover the binder should be reported.
WARNING - The use of this European Standard may involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the determination of the loss in mass of industrial bitumen after heating. The method is used to detect volatile components.
NOTE   The users of the method are encouraged to gather comparative information on binders using this standard, EN 13303 and EN 12607-2 [1] at 163 °C to facilitate the transition to the use of only one standard.
WARNING - The use of this standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Dokument predpisuje minimalne kakovostne zahteve za bitumenske raztopine, ki se uporabljajo za
pripravo podlage gradbenih objektov, kjer se bo vgrajevala bitumenska hidroizolacija.
Bitumenska raztopina pomeni raztopino bitumna v organskem topilu oziroma raztopino bitumna v
tekočem stanju s primerno viskoznostjo za uporabo. Materiali, ki so predmet tega standarda, se
vgrajujejo brez dodatnega segrevanja. Vgradnja poteka ponavadi z mazanjem s pleskarskim
valjčkom, s čopičem ali brizganjem. Materiali (topila) za redčenje premazov ne smejo vsebovati snovi,
ki so sestavni del Priloge XVII Uredbe o registraciji, evalvaciji, avtorizaciji in omejevanju kemikalij –
REACH (Uredba EU št. 1907/2006).
Glede na podnebne razmere v naši državi se ocenjuje, da Slovenija potrebuje svoje minimalne
kriterije kakovosti. Člani SIST/TC VLA Vlaga menijo, da bi bili brez postavljenih ustreznih kriterijev
lahko oškodovani predvsem posamezni uporabniki teh materialov, še posebej, ker za te izdelke ne
obstaja harmonizirana evropska norma.
Tudi druge evropske države pripravljajo svoje nacionalne zahteve. Po posvetih v Sekciji za
hidroizolacije pri Združenju asfalterjev Slovenije, ki je pobudnik priprave ustreznega slovenskega
predpisa, člani SIST/TC VLA ocenjujejo, da je novi nacionalni standard učinkovit postopek za pripravo
kakovostnih zahtev.

  • Standard
    3 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day

This document specifies a test method for the evaluation of the resistance to impact puncturing of a sheet or sheet system.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Corrigendum issued due to mistake from TC in Table ZA.1 (SV on 2017-06-02)

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies a test method for the evaluation of the resistance of a bitumen sheet to compaction of an asphalt layer.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a test method for the determination of water absorption in reinforced bitumen sheets which could influence the functional behaviour of these sheets.
NOTE   It is primarily the reinforcement's ability to absorb water which is examined by this test.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies definitions and characteristics of flexible plastic and rubber sheets which are intended to be used as damp proofing for buildings, including basement tanking. It specifies the requirements and test methods, and provides for the evaluation of conformity of the products with the requirements of this standard.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard is applicable to bitumen sheets intended for use with a layer of mastic asphalt.
This European Standard specifies a test method for the evaluation of the resistance of bitumen sheets to the rising of the bitumen compound at the application of mastic asphalt in a non-floating manner.
Note   This European Standard could also be used for bitumen sheets intended for use with other asphalt types as a protection layer.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a test method for the evaluation of the compatibility of the waterproofing system applied to a concrete surface and covered with an asphalt layer. The complete system is exposed to an accelerated heat conditioning followed by a determination of the shear strength properties before and after heat conditioning.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document is one of a series of standards applicable to flexible sheets for waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles.
This document specifies a test method for the evaluation of the shear strength properties of the waterproofing sheet system applied to a concrete surface and with an asphalt layer.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies procedures for assessment and verification of constancy of performance of sealants for non-structural use in joints in building construction and pedestrian walkways.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Technical Report provides guidance for CE marking and Declaration of Performance (DoP) for sealants for joints in building construction.

  • Technical report
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical report
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies definitions and requirements for non-structural elastic sealants used for sealing glazing in building construction applications.
It covers glazing joints from 7° horizontal. Main areas of application are:
-   glass to glass;
-   glass to frame;
-   glass to porous substrates.
Excluding aquariums, structural bonding/glazing, inner and outer seal to manufacture insulated glazing units, horizontal glazing (below 7°), organic glass (e.g. polycarbonate, PMMA, etc.).

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies definitions and requirements for non-structural facade sealants intended for sealing exterior wall joints, window and door perimeter joints in building construction, including the interior face.
NOTE   Provisions on assessment and verification of constancy of performance - AVCP (i.e. Product type determination and Factory Production Control) and marking of these products are given in EN 15651-5.
This European Standard does not apply to non-structural sealants in any of non-paste form, to those used in interior walls and/or partitions and to oil-based mastics.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies definitions and requirements for cold applied non-structural elastic sealants used for movement joints in floors in building construction for interior and exterior use.
Areas of application are: floor joints designed for pedestrian walkways, public areas, movement joints between concrete slabs, areas with pedestrian load, areas used with trolleys, walkable floors, balconies, terraces, warehouses.
NOTE   Provisions on assessment and verification of constancy of performance - AVCP (i.e. Product type determination and Factory Production Control) and marking of these products are given in EN 15651-5.
Chemical containment, cold applied joint sealants for concrete pavements to be used in roads, airfields and sewage treatment plants, perimeter seals and seals in wood floors are excluded.
This European Standard does not apply to non-structural sealants in any of non-paste form, to those used in pedestrian walkways.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies definitions and requirements for sealants used for sealing of joints applied in sanitary areas in the interior of buildings exposed to non-pressurized water.
It covers joints in:
-   bathrooms;
-   toilets;
-   showers;
-   domestic kitchens;
-   prefabricated elements in sanitary areas (e.g. shower cubicles).
Industrial, drinking water, underwater (swimming pools, sewage systems, etc.), food contact applications and sealing of glass-ceramic cooktop panels (stove tops, ceramic hobs) are excluded from the scope.
This European Standard does not provide criteria or recommendations for the design of joints and installation of sealants in sanitary applications.
NOTE   Provisions on assessment and verification of constancy of performance - AVCP (i.e. Product type determination and Factory Production Control) and marking of these products are given in EN 15651-5.
This European Standard does not apply to non-structural sealants in any of non-paste form, to those used in sanitary joints and to oil-based mastics.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the determination of the fines mixing time of diluted cationic bituminous emulsions, under standardized conditions.
WARNING - The use of this European Standard may involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For environmental reasons and to reduce emissions to air, water and soil, it is recommended to limit the use of products, solvents and energy to the minimum required for a valid test result.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for determining the tensile properties of a bituminous binder, in particular those of a polymer modified bitumen, by means of a tensile test.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a quick method for determining, by evaporation, the water content of bituminous road emulsions, with or without polymer added.
For bituminous emulsions without flux oil, bituminous emulsions containing vegetal flux oil, and bituminous emulsions containing up to 1,5 % mass of mineral flux oil in the emulsion, this European Standard, according to the selected operating conditions, is considered as an alternative method to the reference method EN 1428 [1].
Above a mineral flux oil content of 1,5 % by mass, depending on the volatility of the flux oil:
—   the present method can be used up to a flux oil content above 1,5 % by mass if the user can prove its reliability in comparison to EN 1428.
—   the present method can only be used by correcting the result by means of a previously established correlation with the reference method EN 1428.
NOTE   Polymer modified emulsions can behave differently in the test than unmodified emulsions; in case of doubt, the method is checked against EN 1428.
In case of dispute, the water content should be determined according to EN 1428.
WARNING - The use of this European Standard can involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For environmental reasons and to reduce emissions to air, water and soil, it is recommended to limit the use of products, solvents and energy to the minimum required for a valid test result.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the determination of the breaking value of cationic bituminous emulsions.
WARNING - The use of this European Standard may involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For environmental reasons and to reduce emissions to air, water and soil, it is recommended to limit the use of products, solvents and energy to the minimum required for a valid test result.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the determination of the adhesivity of cut-back and fluxed bituminous binders coated onto aggregate when immersed in water.
WARNING The use of this document may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. For environmental reasons and to reduce emissions to air, water and soil, it is recommended to limit the use of products, solvents and energy to the minimum required for a valid test result.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard applies to the apparatus and the test procedure used for the determination of the adhesion of granules to factory made bituminous sheets for roofing. It can also be used in other areas where it is relevant.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This test method covers the determination of percent recovery and non-recoverable creep compliance of bitumen and bituminous binders by means of Multiple Stress Creep and Recovery (MSCR) testing. The MSCR test is conducted using the Dynamic Shear Rheometer (DSR) in creep mode at a specified temperature.
1.2   This standard is appropriate for unaged material, material aged in accordance with EN 12607-1 (RTFOT), material aged in accordance with EN 14769 (PAV), material aged in accordance with both EN 12607-1 and EN 14769.
Other ageing methods, for example EN 15323 (RCAT) can also be used to produce material for this standard.
1.3   The percent recovery at multiple stress levels is intended to determine the presence of elastic response and stress dependence of bituminous binders.
1.4   The non-recoverable creep compliance at multiple stress levels is intended as an indicator for the sensitivity to permanent deformation and stress dependence of bituminous binders.
1.5   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of EN 13924 provides a framework for specifying the properties and relevant test methods for hard paving grade bitumens which are suitable for use in the construction and maintenance of roads, airfields and other paved areas.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a procedure for determining the paraffin wax content of bitumen and bituminous binder by the DIN method.
Aqueous bituminous binders, fluxed or cut-back anhydrous binders, and modified binders, whatever their consistency, are not within the scope of the present test method.
WARNING - Use of this European standard can involve hazardous materials, operations and equipment. This European standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for determining the consistency of bitumen and bituminous binders. Normal procedure is described for penetrations up to 330 x 0,1 mm, but for penetrations above this value, up to 500 x 0,1 mm, different operating parameters are necessary.
WARNING - Use of this European Standard may involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the determination of the softening point of bitumen and bituminous binders in the range of 28 °C to 150 °C.
NOTE   The method described is also applicable to bituminous binders that have been recovered from bituminous mixes, e.g. by extraction.
WARNING - Use of this European Standard can involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day