Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation

This part of the EN 13523 series specifies the basic principles and procedure for determining the resistance of an organic coating on a metallic substrate (coil coating) to a combination of fluorescent UV radiation, and water condensation and temperature under controlled conditions.
Due to varied conditions which occur during natural weathering and the extreme nature of accelerated testing, correlation between the two cannot be expected.
Not all organic coatings will perform on an equal basis but a degree of correlation between the same generic type might be observed.

Bandbeschichtete Metalle - Prüfverfahren - Teil 10: Beständigkeit gegen UV-Strahlung mit Leuchtstofflampen und Kondensation von Wasser

Tôles prélaquées - Méthodes d'essai - Partie 10 : Résistance à un rayonnement UV fluorescent et à la condensation de l'eau

Le présent document spécifie les principes de base et le mode opératoire à appliquer pour déterminer la résistance d’un revêtement organique appliqué sur un support métallique (prélaquage en bandes continues), à une combinaison d’un rayonnement UV fluorescent, de condensation d’eau et de température, dans des conditions contrôlées.
Compte tenu des diverses conditions qui règnent pendant le processus de vieillissement naturel et de la nature extrême des essais accélérés, aucune corrélation ne peut être escomptée entre les deux.
Tous les revêtements organiques ne se comporteront pas de la même manière, mais un certain degré de corrélation peut apparaître entre ceux de même type générique.

Prevlečene kovine, ki se navijajo - Preskusne metode - 10. del: Odpornost proti fluorescentni ultravijolični svetlobi in kondenzaciji vode

General Information

Status
Not Published
Public Enquiry End Date
02-Oct-2023
Technical Committee
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
09-Jun-2023
Due Date
27-Oct-2023
Completion Date
13-Oct-2023

Relations

Buy Standard

Draft
prEN 13523-10:2023
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 13523-10:2023
01-september-2023
Prevlečene kovine, ki se navijajo - Preskusne metode - 10. del: Odpornost proti
fluorescentni ultravijolični svetlobi in kondenzaciji vode
Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and
water condensation
Bandbeschichtete Metalle - Prüfverfahren - Teil 10: Beständigkeit gegen UV-Strahlung
mit Leuchtstofflampen und Kondensation von Wasser
Tôles prélaquées - Méthodes d'essai - Partie 10 : Résistance à un rayonnement UV
fluorescent et à la condensation de l'eau
Ta slovenski standard je istoveten z: prEN 13523-10
ICS:
17.180.20 Barve in merjenje svetlobe Colours and measurement of
light
25.220.60 Organske prevleke Organic coatings
oSIST prEN 13523-10:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13523-10:2023

---------------------- Page: 2 ----------------------
oSIST prEN 13523-10:2023


DRAFT
EUROPEAN STANDARD
prEN 13523-10
NORME EUROPÉENNE

EUROPÄISCHE NORM

July 2023
ICS 25.220.60 Will supersede EN 13523-10:2017
English Version

Coil coated metals - Test methods - Part 10: Resistance to
fluorescent UV radiation and water condensation
Tôles prélaquées - Méthodes d'essai - Partie 10 : Bandbeschichtete Metalle - Prüfverfahren - Teil 10:
Résistance à un rayonnement UV fluorescent et à la Beständigkeit gegen UV-Strahlung mit
condensation de l'eau Leuchtstofflampen und Kondensation von Wasser
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 139.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13523-10:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13523-10:2023
prEN 13523-10:2023 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus and materials . 6
6 Sampling . 6
7 Test panels . 6
8 Procedure . 6
8.1 Exposure .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.