iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 17409:2020

(Main)

Electrically propelled road vehicles - Conductive power transfer - Safety requirements (ISO 17409:2020)

Electrically propelled road vehicles - Conductive power transfer - Safety requirements (ISO 17409:2020)

This document specifies electric safety requirements for conductive connection of electrically propelled road vehicles to external electric circuits. External electric circuits include external electric power supplies and external electric loads. This document provides requirements for the charging modes 2, 3, 4, as defined in IEC 61851-1, and reverse power transfer. For mode 4, this document provides requirements regarding the connection to an isolated DC EV charging station according to IEC 61851-23.
NOTE 1  This edition does not provide requirements for mode 1.
NOTE 2  External electric circuits are not part of the vehicle.
This document applies to the on-board sections of vehicle power supply circuits. It applies also to dedicated power supply control functions used for the connection of the vehicle to an external electric circuit.
It does not provide comprehensive safety information for manufacturing, maintenance and repair personnel.
NOTE 3  ISO 6469-3 provides general electrical safety requirements for electrically propelled road vehicles.
NOTE 4  With this edition of this document the limitation of y-capacitance for protection against electric shock under single failure conditions is no longer applicable as a fault protection provision when the vehicle has a conductive DC connection to an external electric circuit.

Elektrisch angetriebene Straßenfahrzeuge - Kabelgebundene Energieübertragung - Sicherheitsanforderungen (ISO 17409:2020)

Dieses Dokument legt die elektrischen Sicherheitsanforderungen für die leitfähige Verbindung von elektrisch angetriebenen Straßenfahrzeugen mit externen Stromkreisen fest. Externe Stromkreise umfassen externe elektrische Versorgungssysteme und externe elektrische Lasten. Dieses Dokument enthält Anforderungen für die Ladebetriebsarten 2, 3, 4, wie in IEC 61851 1 festgelegt, sowie die rückwärtsgerichtete Leistungsübertragung. Für Ladebetriebsart 4 enthält dieses Dokument Anforderungen an den Anschluss an eine isolierte Gleichstrom-Ladestation für Elektrofahrzeuge entsprechend IEC 61851 23.
ANMERKUNG Diese Ausgabe enthält keine Anforderungen für Ladebetriebsart 1.
ANMERKUNG 2 Externe Stromkreise sind nicht Teil des Fahrzeugs.
Dieses Dokument gilt für die fahrzeugseitigen Abschnitte der Versorgungsstromkreise des Fahrzeuges. Es gilt auch für spezielle Funktionen zur Steuerung der Stromversorgung, die für den Anschluss des Fahrzeugs an einen externen Stromkreis verwendet werden.
Es enthält keine umfassenden Sicherheitsinformationen für das Herstellungs-, Wartungs- und Reparaturpersonal.
ANMERKUNG 3 ISO 6469 3 enthält allgemeine elektrische Sicherheitsanforderungen für elektrisch angetriebene Straßenfahrzeuge.
ANMERKUNG 4 Mit dieser Ausgabe dieses Dokuments ist die Begrenzung der y Kapazität zum Schutz gegen elektrischen Schlag unter Einzelfehlerzustand nicht mehr als Fehlerschutzbestimmung anwendbar, wenn das Fahrzeug über eine leitfähige Gleichstromverbindung zu einem externen Stromkreis verfügt.

Véhicules routiers à propulsion électrique - Transfert de puissance par conduction - Exigences de sécurité (ISO 17409:2020)

Le présent document spécifie les exigences de sécurité électrique relatives à la connexion par conduction des véhicules routiers à propulsion électrique à des circuits électriques externes. Les circuits électriques externes englobent les sources d'alimentation électrique externes et les charges électriques externes. Le présent document définit les exigences pour la recharge des modes 2, 3 et 4, tel que défini dans l'IEC 61851‑1, et pour le transfert de puissance réversible. Pour le mode 4, le présent document fournit les exigences concernant la connexion à une borne de charge CC isolée, conformément à l'IEC 61851‑23.
NOTE 1  Cette édition ne définit pas les exigences relatives au mode 1.
NOTE 2  Les circuits électriques extérieurs ne font pas partie du véhicule.
Le présent document s'applique aux parties embarquées des circuits d'alimentation des véhicules. Elle s'applique également aux fonctions dédiées de contrôle de l'alimentation électrique utilisées pour la connexion du véhicule à un circuit électrique externe.
Le présent document ne fournit pas d'informations complètes concernant la sécurité pour le personnel de fabrication, de maintenance et de réparation.
NOTE 3  L'ISO 6469‑3 fournit les exigences générales de sécurité électrique pour les véhicules routiers à propulsion électrique.
NOTE 4  Avec l'édition du présent document, la limitation de la capacité y pour la protection contre les chocs électriques dans des conditions de défaillance unique ne s'applique plus en tant que disposition de protection contre les défaillances, lorsque le véhicule dispose d'une connexion par conduction en courant continu avec un circuit électrique externe.

Cestna vozila na električni pogon - Prevodni prenos moči - Varnostne zahteve (ISO 17409:2020)

General Information

Status
Published
Publication Date
10-Mar-2020
Withdrawal Date
29-Sep-2020
ICS
43.120 - Electric road vehicles
Technical Committee
CEN/TC 301 - Electrically propelled road vehicles
Drafting Committee
CEN/TC 301 - Electrically propelled road vehicles
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
11-Mar-2020
Completion Date
11-Mar-2020
Directive
2014/94/EU - Directive 2014/94/EU of The European Parliament and of The Council of 22 October 2014 on the deployment of alternative fuels infrastructure
Mandate
M/468 - Standardisation mandate addressed to CEN and CENELEC and ETSI concerning the charging of electric vehicles
M/533 - [C(2015)1330] Standardisation request addressed to CEN, CENELEC and ETSI in support of the implementation of the Directive 2014/94/EU on the deployment of alternative fuels infrastructure
Ref Project
SIST EN ISO 17409:2020 - Electrically propelled road vehicles - Conductive power transfer - Safety requirements (ISO 17409:2020)

Relations

Replaces
EN ISO 17409:2017 - Electrically propelled road vehicles - Connection to an external electric power supply - Safety requirements (ISO 17409:2015, Corrected version 2015-12-15)
Effective Date
08-Jun-2022

Buy Standard

EN ISO 17409:2020 - BARVEEN ISO 17409:2020 - BARVE
PreviousNext
Standard
EN ISO 17409:2020 - BARVE
English language
49 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 17409:2020
01-junij-2020
Nadomešča:
SIST EN ISO 17409:2017
Cestna vozila na električni pogon - Prevodni prenos moči - Varnostne zahteve (ISO
17409:2020)
Electrically propelled road vehicles - Conductive power transfer - Safety requirements
(ISO 17409:2020)
Elektrisch angetriebene Straßenfahrzeuge - Kabelgebundene Energieübertragung -
Sicherheitsanforderungen (ISO 17409:2020)
Véhicules routiers à propulsion électrique - Transfert d'énergie conductive - Exigences
de sécurité (ISO 17409:2020)
Ta slovenski standard je istoveten z: EN ISO 17409:2020
ICS:
43.120 Električna cestna vozila Electric road vehicles
SIST EN ISO 17409:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 17409:2020

---------------------- Page: 2 ----------------------
SIST EN ISO 17409:2020


EN ISO 17409
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2020
EUROPÄISCHE NORM
ICS 43.120 Supersedes EN ISO 17409:2017
English Version

Electrically propelled road vehicles - Conductive power
transfer - Safety requirements (ISO 17409:2020)
Véhicules routiers à propulsion électrique - Transfert Elektrisch angetriebene Straßenfahrzeuge -
de puissance par conduction - Exigences de sécurité Kabelgebundene Energieübertragung -
(ISO 17409:2020) Sicherheitsanforderungen (ISO 17409:2020)
This European Standard was approved by CEN on 18 February 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17409:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 17409:2020
EN ISO 17409:2020 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 17409:2020
EN ISO 17409:2020 (E)
European foreword
This document (EN ISO 17409:2020) has been prepared by Technical Committee ISO/TC 22 "Road
vehicles" in collaboration with Technical Committee CEN/TC 301 “Road vehicles” the secretariat of
which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2020, and conflicting national standards
shall be withdrawn at the latest by September 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 17409:2017.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 17409:2020 has been approved by CEN as EN ISO 17409:2020 without any modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 17409:2020

---------------------- Page: 6 ----------------------
SIST EN ISO 174
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 15118-9:2023(Main)
Road vehicles - Vehicle to grid communication interface - Part 9: Physical and data link layer conformance test for wireless communication (ISO 15118-9:2022)
SIST EN ISO 15118-9:2023

This document specifies conformance tests in the form of an abstract test suite (ATS) for a system under test (SUT) implementing an electric-vehicle or supply-equipment communication controller (EVCC or SECC) with support for WLAN-based high-level communication (HLC) according to ISO 15118‑8 and against the background of ISO 15118-1. These conformance tests specify the testing of capabilities and behaviours of an SUT, as well as checking what is observed against the conformance requirements specified in ISO 15118‑8 and against what the implementer states the SUT implementation's capabilities are.
The capability tests within the ATS check that the observable capabilities of the SUT are in accordance with the static conformance requirements defined in ISO 15118‑8. The behaviour tests of the ATS examine an implementation as thoroughly as practical over the full range of dynamic conformance requirements defined in ISO 15118‑8 and within the capabilities of the SUT (see NOTE below).
A test architecture is described in correspondence to the ATS. The abstract test cases in this document are described leveraging this test architecture and are specified in descriptive tabular format for the ISO/OSI physical and data link layers (layers 1 and 2).
In terms of coverage, this document only covers normative sections and requirements in ISO 15118‑8. This document can additionally refer to specific tests for requirements on referenced standards (e.g. IEEE, or industry consortia standards, like WiFi Alliance) as long as they are relevant in terms of conformance for implementations according to ISO 15118‑8. However, it is explicitly not intended to widen the scope of this conformance specification to such external standards, if it is not technically necessary for the purpose of conformance testing for ISO 15118‑8. Furthermore, the conformance tests specified in this document do not include the assessment of performance nor robustness or reliability of an implementation. They cannot provide judgments on the physical realization of abstract service primitives, how a system is implemented, how it provides any requested service, nor the environment of the protocol implementation. Furthermore, the abstract test cases defined in this document only consider the communication protocol and the system's behaviour defined ISO 15118‑8. The power flow between the EVSE and the EV is not considered.
NOTE       Practical limitations make it impossible to define an exhaustive test suite, and economic considerations can restrict testing even further. Hence, the purpose of this document is to increase the probability that different implementations are able to interwork. This is achieved by verifying them by means of a protocol test suite, thereby increasing the confidence that each implementation conforms to the protocol specification. However, the specified protocol test suite cannot guarantee conformance to the specification since it detects errors rather than their absence. Thus, conformance to a test suite alone cannot guarantee interworking. Instead, it gives confidence that an implementation has the required capabilities and that its behaviour conforms consistently in representative instances of communication.

  • Standard
    80 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-20:2022(Main)
Road vehicles - Vehicle to grid communication interface - Part 20: 2nd generation network layer and application layer requirements (ISO 15118-20:2022)
SIST EN ISO 15118-20:2022

This document specifies the communication between the electric vehicle (EV), including battery electric vehicle (BEV) and plug-in hybrid electric vehicle (PHEV), and the electric vehicle supply equipment (EVSE). The application layer messages defined in this document are designed to support the electricity power transfer between an EV and an EVSE.
This document defines the communication messages and sequence requirements for bidirectional power transfer.
This document furthermore defines requirements of wireless communication for both conductive charging and wireless charging as well as communication requirements for automatic connection device and information services about charging and control status.
The purpose of this document is to detail the communication between an electric vehicle communication controller (EVCC) and a supply equipment communication controller (SECC). Aspects are specified to detect a vehicle in a communication network and enable an Internet Protocol (IP) based communication between the EVCC and the SECC.

  • Standard
    570 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19363:2021(Main)
Electrically propelled road vehicles - Magnetic field wireless power transfer - Safety and interoperability requirements (ISO 19363:2020)
SIST EN ISO 19363:2021

This document defines the requirements and operation of the on-board vehicle equipment that enables magnetic field wireless power transfer (MF-WPT) for traction battery charging of electric vehicles. It is intended to be used for passenger cars and light duty vehicles.
This document addresses the following aspects for an EV device:
—     safety requirements;
—     transferred power and power transfer efficiency;
—     ground clearance of the EV device;
—     functionality with associated off-board systems under various conditions and independent of manufacturer;
—     test procedures.
EV devices that fulfil the requirements in this document are intended to operate with supply devices that fulfil the MF-WPT related requirements in the IEC 61980 series.
NOTE 1  Charging of a vehicle in motion is not considered in this edition.
NOTE 2  Bi-directional power transfer is not considered in this edition.

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-8:2020(Main)
Road vehicles - Vehicle to grid communication interface - Part 8: Physical layer and data link layer requirements for wireless communication (ISO 15118-8:2020)
SIST EN ISO 15118-8:2020

This document specifies the requirements of the physical and data link layer of a wireless High Level Communication (HLC) between Electric Vehicles (EV) and the Electric Vehicle Supply Equipment (EVSE). The wireless communication technology is used as an alternative to the wired communication technology as defined in ISO 15118‑3.
It covers the overall information exchange between all actors involved in the electrical energy exchange. ISO 15118 (all parts) are applicable for conductive charging as well as Wireless Power Transfer (WPT).
For conductive charging, only EVSEs compliant with "IEC 61851‑1 modes 3 and 4" and supporting HLC are covered by this document. For WPT, charging sites according to IEC 61980 (all parts) and vehicles according to ISO 19363 are covered by this document.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-1:2019(Main)
Road vehicles - Vehicle to grid communication interface - Part 1: General information and use-case definition (ISO 15118-1:2019)
SIST EN ISO 15118-1:2019

This document, as a basis for the other parts of the ISO 15118 series, specifies terms and definitions, general requirements and use cases for conductive and wireless HLC between the EVCC and the SECC.
This document is applicable to HLC involved in conductive and wireless power transfer technologies in the context of manual or automatic connection devices.
This document is also applicable to energy transfer either from EV supply equipment to charge the EV battery or from EV battery to EV supply equipment in order to supply energy to home, to loads or to the grid.
This document provides a general overview and a common understanding of aspects influencing identification, association, charge or discharge control and optimisation, payment, load levelling, cybersecurity and privacy. It offers an interoperable EV-EV supply equipment interface to all e-mobility actors beyond SECC.
The ISO 15118 series does not specify the vehicle internal communication between battery and other internal equipment (beside some dedicated message elements related to the energy transfer).
NOTE 1    Electric road vehicles specifically are vehicles in categories M (used for carriage of passengers) and N (used for carriage of goods) (compare ECE/TR ANS/WP.29/78 ev.2). This does not prevent vehicles in other categories from adopting the ISO 15118 series as well.
NOTE 2    This document is destined to orientate the message set of ISO 15118‑2 and ISO 15118‑20[1]. The absence of any particular use case in this document does not imply that it will not be put into practice, with the required messages.
NOTE 3    This document, ISO 15118‑2 and ISO 15118‑20 are designed to work independent of data transfer medium used. However, the ISO 15118 series is made for fitting the specified data link layers in the corresponding documents in this series.
[1] Under preparation. Stage at the time on publication: ISO/DIS 15118-20:2019.

  • Standard
    126 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17186:2019(Main)
Identification of vehicles and infrastructures compatibility - Graphical expression for consumer information on EV power supply
SIST EN 17186:2019

This document lays down harmonized identifiers for power supply for electric road vehicles. The requirements in this standard are to complement the informational needs of users regarding the compatibility between the EV charging stations, the cable assemblies and the vehicles that are placed on the market. The identifier is intended to be visualized at EV charging stations, on vehicles, on cable assemblies, in EV dealerships and in consumer manuals as described in this document.
Power supply for EVs uses vehicle inlets, socket-outlets, connectors and plugs, as mentioned in EN IEC 61851-1:— and EN 62196-1:2014.
This document defines for each harmonized identifier the size, shape, colour and other information of relevance for compatibility recognition, as well as the label location.
The station side identifier gives unmistakable compatibility information with either the plug of the cable assembly in case of a socket outlet configuration, or the vehicle inlet in case of attached cable configuration.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-4:2019(Main)
Road vehicles - Vehicle to grid communication interface - Part 4: Network and application protocol conformance test (ISO 15118-4:2018)
SIST EN ISO 15118-4:2019

ISO 15118-4:2018 specifies conformance tests in the form of an Abstract Test Suite (ATS) for a System Under Test (SUT) implementing an EVCC or SECC according to ISO 15118-2. These conformance tests specify the testing of capabilities and behaviors of an SUT as well as checking what is observed against the conformance requirements specified in ISO 15118-2 and against what the supplier states the SUT implementation's capabilities are.
The capability tests within the ATS check that the observable capabilities of the SUT are in accordance with the static conformance requirements defined in ISO 15118-2. The behavior tests of the ATS examine an implementation as thoroughly as is practical over the full range of dynamic conformance requirements defined in ISO 15118-2 and within the capabilities of the SUT (see NOTE).
A test architecture is described in correspondence to the ATS. The conformance test cases in this document are described leveraging this test architecture and are specified in TTCN-3 Core Language for ISO/OSI Network Layer (Layer 3) and above. The conformance test cases for the Data Link Layer (Layer 2) and Physical Layer (Layer 1) are described in ISO 15118-5. Test cases with overlapping scopes are explicitly detailed.
This document does not include specific tests of other standards referenced within ISO 15118-2, e.g. IETF RFCs. Furthermore, the conformance tests specified in this document do not include the assessment of performance nor robustness or reliability of an implementation. They cannot provide judgments on the physical realization of abstract service primitives, how a system is implemented, how it provides any requested service, nor the environment of the protocol implementation. Furthermore, the test cases defined in this document only consider the communication protocol defined ISO 15118-2. Power flow between the EVSE and the EV is not considered.
NOTE 1    Practical limitations make it impossible to define an exhaustive test suite, and economic considerations can restrict testing even further. Hence, the purpose of this document is to increase the probability that different implementations are able to interwork. This is achieved by verifying them by means of a protocol test suite, thereby increasing the confidence that each implementation conforms to the protocol specification. However, the specified protocol test suite cannot guarantee conformance to the specification since it detects errors rather than their absence. Thus conformance to a test suite alone cannot guarantee interworking. What it does do is give confidence that an implementation has the required capabilities and that its behavior conforms consistently in representative instances of communication.
NOTE 2    This document has some interdependencies to the conformance tests defined in ISO 15118-5 which result from ISO/OSI cross layer dependencies in the underlying protocol specification (e.g. for sleep mode)

  • Standard
    1470 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-5:2019(Main)
Road vehicles - Vehicle to grid communication interface - Part 5: Physical layer and data link layer conformance test (ISO 15118-5:2018)
SIST EN ISO 15118-5:2019

ISO 15118-5:2018 specifies conformance tests in the form of an Abstract Test Suite (ATS) for a System Under Test (SUT) implementing an Electric Vehicle or Supply Equipment Communication Controller (EVCC or SECC) with support for PLC-based High Level Communication (HLC) and Basic Signaling according to ISO 15118‑3. These conformance tests specify the testing of capabilities and behaviors of an SUT, as well as checking what is observed against the conformance requirements specified in ISO 15118‑3 and against what the implementer states the SUT implementation's capabilities are.
The capability tests within the ATS check that the observable capabilities of the SUT are in accordance with the static conformance requirements defined in ISO 15118‑3. The behavior tests of the ATS examine an implementation as thoroughly as is practical over the full range of dynamic conformance requirements defined in ISO 15118‑3 and within the capabilities of the SUT (see NOTE 1).
A test architecture is described in correspondence to the ATS. The conformance test cases in this part of the standard are described leveraging this test architecture and are specified in TTCN-3 Core Language for the ISO/OSI Physical and Data Link Layers (Layers 1 and 2). The conformance test cases for the ISO/OSI Network Layer (Layer 3) and above are described in ISO 15118‑4.
In terms of coverage, this document only covers normative sections and requirements in ISO 15118‑3. This document can additionally include specific tests for requirements of referenced standards (e.g. IEEE, or industry consortia standards) as long as they are relevant in terms of conformance for implementations according to ISO 15118‑3. However, it is explicitly not intended to widen the scope of this conformance specification to such external standards, if it is not technically necessary for the purpose of conformance testing for ISO 15118‑3. Furthermore, the conformance tests specified in this document do not include the assessment of performance nor robustness or reliability of an implementation. They cannot provide judgments on the physical realization of abstract service primitives, how a system is implemented, how it provides any requested service, nor the environment of the protocol implementation. Furthermore, the test cases defined in this document only consider the communication protocol and the system's behavior defined ISO 15118‑3. Power flow between the EVSE and the EV is not considered.
NOTE 1    Practical limitations make it impossible to define an exhaustive test suite, and economic considerations can restrict testing even further. Hence, the purpose of this document is to increase the probability that different implementations are able to interwork. This is achieved by verifying them by means of a protocol test suite, thereby increasing the confidence that each implementation conforms to the protocol specification. However, the specified protocol test suite cannot guarantee conformance to the specification since it detects errors rather than their absence. Thus conformance to a test suite alone cannot guarantee interworking. What it does do is give confidence that an implementation has the required capabilities and that its behavior conforms consistently in representative instances of communication.
NOTE 2    This document has some interdependencies to the conformance tests defined in ISO 15118‑4 which result from ISO/OSI cross layer dependencies in the underlying protocol specification (e.g. for

  • Standard
    414 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-3:2016(Main)
Road vehicles - Vehicle to grid Communication interface - Part 3: Physical and data link layer requirements (ISO 15118-3:2015)
SIST EN ISO 15118-3:2016

ISO 15118-3:2015 specifies the requirements of the physical and data link layer for a high-level communication, directly between battery electric vehicles (BEV) or plug-in hybrid electric vehicles (PHEV), termed as EV (electric vehicle) [ISO-1], based on a wired communication technology and the fixed electrical charging installation [Electric Vehicle Supply Equipment (EVSE)] used in addition to the basic signalling, as defined in [IEC-1].
It covers the overall information exchange between all actors involved in the electrical energy exchange. ISO 15118 (all parts) is applicable for manually connected conductive charging.
Only "[IEC-1] modes 3 and 4" EVSEs, with a high-level communication module, are covered by this part of ISO 15118.

  • Standard
    88 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-2:2016(Main)
Road vehicles - Vehicle-to-grid communication Interface - Part 2: Network and application protocol requirements (ISO 15118-2:2014)
SIST EN ISO 15118-2:2016

ISO 15118-2:2014 specifies the communication between battery electric vehicles (BEV) or plug-in hybrid electric vehicles (PHEV) and the Electric Vehicle Supply Equipment. The application layer message set defined in ISO 15118-2:2014 is designed to support the energy transfer from an EVSE to an EV. ISO 15118-1 contains additional use case elements describing the bidirectional energy transfer. The implementation of these use cases requires enhancements of the application layer message set defined herein.
The purpose of ISO 15118-2:2014 is to detail the communication between an EV (BEV or a PHEV) and an EVSE. Aspects are specified to detect a vehicle in a communication network and enable an Internet Protocol (IP) based communication between EVCC and SECC.
ISO 15118-2:2014 defines messages, data model, XML/EXI based data representation format, usage of V2GTP, TLS, TCP and IPv6. In addition, it describes how data link layer services can be accessed from a layer 3 perspective. The Data Link Layer and Physical Layer functionality is described in ISO 15118-3.

  • Standard
    351 pages
    English language
    sale 10% off
    e-Library read for
    1 day